Possible cheap pivots.
-
Wonder if these could be used for pivots...
-
Possible but since they're hollow inside it may make them weaker
Better the SAKperts come in an give there 2 pence though :D -
Wenger and Victorinox made hollow rivet SAKs for years, and it didnt seem to bother anyone (admittedly it was only the bail that was hollow). I think the bigger concern would be that these are only 2mm in diameter, and even that might not be a big deal.
-
@sLaughterMed said:
Wenger and Victorinox made hollow rivet SAKs for years, and it didnt seem to bother anyone (admittedly it was only the bail that was hollow). I think the bigger concern would be that these are only 2mm in diameter, and even that might not be a big deal.Looking at the link they are 3MM would that make a difference
:D I think the 2MM is the inside threaded part 
-
Yes, they are 3mm OD and M2 thread inside.
As far as being hollow and potentially weak, if the screws were selected to be of a length that just met in the middle when the knife was assembled, the pivot would be essentially solid and possibly even stronger than a pure brass pin.I will risk $10 and see what they look like IRL.
Also got some of these M2x12mm csk hex socket head screws. http://www.ebay.com.au/itm/322084789287
-
@PTRSAK said:
Yes, they are 3mm OD and M2 thread inside.
As far as being hollow and potentially weak, if the screws were selected to be of a length that just met in the middle when the knife was assembled, the pivot would be essentially solid and possibly even stronger than a pure brass pin.I will risk $10 and see what they look like IRL.
Also got some of these M2x12mm csk hex socket head screws. http://www.ebay.com.au/itm/322084789287
Can't wait to see how they work

-
In the pictures it looks like the outside surface is knurled or ridged, not smooth - not ideal for pivots.
-
@shibafu said:
In the pictures it looks like the outside surface is knurled or ridged, not smooth - not ideal for pivots.I did look at that, depends on several factors.
How deep are the grooves?
Are they cut or knurled?
If formed by some upsetting operation such as knurlling, is the 3mm dia the final size or the original stock?
What hardness is the brass?
And probably a few others I haven't thought of.
I can see some possible advantages to the grooved surface, especially if they aren't to deep/wide.
The reduced contact area may provide a smoother turning pivot.
The grooves may make the pivot self cleaning or more resistant to gumming up.
Applying a tiny amount if lithium grease or similar during assembly could lubricate the blades for life.
Another method that might work is very lightly tinning them with 60/40 solder and then spinning them in a drill with fine abrasive paper to just expose the peaks of the brass again. Would be a lot of work but I'm sure the lead in the solder would be great as a lubricant. (yes I know lead is toxic, I'm just brainstorming this stuff as I type).I just have an enquiring mind, I get these crazy ideas and have to try them.
Last time it ended up with me figuring out how to fit Wenger scissors into 84mm Vic' knives.At the end of the day I may have wasted a few dollars, if not I've found a source of 10 cent pivots rather than 2 dollars each from places like knifekits.com
-
@PTRSAK said:
I did look at that, depends on several factors.
How deep are the grooves?
Are they cut or knurled?
If formed by some upsetting operation such as knurlling, is the 3mm dia the final size or the original stock?
What hardness is the brass?
And probably a few others I haven't thought of.
I can see some possible advantages to the grooved surface, especially if they aren't to deep/wide.
The reduced contact area may provide a smoother turning pivot.
The grooves may make the pivot self cleaning or more resistant to gumming up.
Applying a tiny amount if lithium grease or similar during assembly could lubricate the blades for life.
Another method that might work is very lightly tinning them with 60/40 solder and then spinning them in a drill with fine abrasive paper to just expose the peaks of the brass again. Would be a lot of work but I'm sure the lead in the solder would be great as a lubricant. (yes I know lead is toxic, I'm just brainstorming this stuff as I type).I just have an enquiring mind, I get these crazy ideas and have to try them.
Last time it ended up with me figuring out how to fit Wenger scissors into 84mm Vic' knives.At the end of the day I may have wasted a few dollars, if not I've found a source of 10 cent pivots rather than 2 dollars each from places like knifekits.com
interesting thoughts, look forward to hearing how it works out. -
Well, the barrels arrived, still waiting on the screws.
Measuring up it would appear that my thoughts were correct in that they appear to have been 3mm stock before being knurled. The final size is about 3.1something or slightly bigger than 3mm but a whisker smaller than 1/8".
They are long enough to hold in a drill chuck and leave enough free to file down to 3mm.The M2 thread appears to be about 5mm deep into the ends and they are drilled the whole way through so after cutting to length it would be no trouble to tap the cut end.
Another use I have already put one to is as a hollow rivet in a Soldier knife. Cut to length and spread the end with a sharp tap on a centrepunch.
Part two follows when the screws arrive.
-
Stand by. There will be some for sale soon ;). That's all I can say at the moment.
-
haha, well I can't see myself getting through 30 knives worth too quickly.
-
Question for you all on pivots. What would pay per pivot? $3-5, $5-7??? I know that sounds like a strange question but I'd like to know to pass on the info. We all know cheaper is better, but quality custom stuff usually demands a higher premium.
-
@tattoosteve99 said:
Question for you all on pivots. What would pay per pivot? $3-5, $5-7??? I know that sounds like a strange question but I'd like to know to pass on the info. We all know cheaper is better, but quality custom stuff usually demands a higher premium.Free is good. :P
Depends on price of materials, plus cost of labor. I say you figure out the price of the materials, and add 10% for wear and tear on bits and things.
Then, assign a value to your labor ($20-$10000000 an hour, whtever you are worth) BEFORE you start. Then, time how long it takes to make a demo set. Calculate based on the value of your labor, and add everything together!
If no one likes your prices, they will tell you with your wallet. Id be interested in some for sure though, if it works out.
-
@tattoosteve99 said:
Question for you all on pivots. What would pay per pivot? $3-5, $5-7??? I know that sounds like a strange question but I'd like to know to pass on the info. We all know cheaper is better, but quality custom stuff usually demands a higher premium.I'd pay more for a 3mm stainless pivot with M2 threads than I'd pay for a 1/8" brass one with 2-56 screws.
-
Bump!! I have some news. The person who is making these is done with the prototyping and heat treatment. I will be testing these out on my personal EDC sak as soon as they arrive

-
And I have some!! I will be testing these shortly on my EDC

From the lack of enthusiasm on this thread you'd think no one is interested
-
Well you know we prefer pictures around these parts. ;)
:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
