Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Old cross Woodsman into not-quite-an-Electrician mod

Scheduled Pinned Locked Moved The Mod Squad
35 Posts 1 Posters 5.8k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Old cross Woodsman into not-quite-an-Electrician mod
Old cross Woodsman into not-quite-an-Electrician mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • hiraethus Offline
    hiraethus
    Admin Team
    Posts: 6,969
    hiraethus Offline
    hiraethus
    Admin Team
    wrote on last edited by
    Quote Reply

      Had a request to build a knife with red old cross scales, with a slightly odd tool layout - Awl/Electrician's blade and opener layer. Received the donor knives in the post last week, but have only just got started on the mod.

      I was a little surprised that the donor scales were on a Woodsman, but it's past saving and I have no problem taking it apart.

      Carefully marked the centres of the rivets and drilled them out with a carbide stub drill.

      Punched the drilled pins out. Had to get the Dremel and a diamond burr out on one - had drilled slightly off-centre and couldn't get a clean hole.

      Repeat the process on the Electrician

      This was even more problematic, and I decided to swap the stub drill for a proper centre drill. These are much stiffer and won't wander off-centre. Should have used it to start with.

      Test fit of the parts, using two opener layer springs as I don't need the thicker blade spring for the narrow electrician's blade:

      The electrician's blade nail nick is partially blocked by the can opener, so I'll play with the layout tomorrow and see if I can improve things.

      Next up: need to drill the scales for the larger diameter centre pin, make the pins and re-assemble. And tidy my workbench:

      1 Reply Last reply
      • kirk13 Offline
        kirk13
        Admin Team
        Posts: 15,955
        kirk13 Offline
        kirk13
        Admin Team
        wrote on last edited by
        #1 Quote Reply

          :popcorn: :popcorn: :popcorn:

          1 Reply Last reply
          • Zed Offline
            Zed
            Posts: 19,555
            Zed Offline
            Zed
            wrote on last edited by
            #2 Quote Reply

              Indeed :popcorn:

              1 Reply Last reply
              • Syph007 Offline
                Syph007
                Global Moderators
                Posts: 9,842
                Syph007 Offline
                Syph007
                Global Moderators
                wrote on last edited by Syph007
                #3 Quote Reply

                  I love seeing in progress modding. :D

                  Your work area is significantly cleaner than mine. :D

                  You might be able to change the angle of the pivot for the eblade to get it to sit a little higher in closed position.

                  1 Reply Last reply
                  • zoidberg Offline
                    zoidberg
                    Posts: 38,161
                    zoidberg Offline
                    zoidberg
                    wrote on last edited by
                    #4 Quote Reply

                      Process pics are sweet. :tu: What about swapping the e blade and bottle opener? :think:

                      1 Reply Last reply
                      • hiraethus Offline
                        hiraethus
                        Admin Team
                        Posts: 6,969
                        hiraethus Offline
                        hiraethus
                        Admin Team
                        wrote on last edited by
                        #5 Quote Reply

                          @Syph007 said:
                          I love seeing in progress modding. :D

                          Your work area is significantly cleaner than mine. :D

                          :salute:

                          See that pile of crap at the top of the last photo? It's been spreading outwards for the last year and is threatening to take over the entire bench. I've just bought a second stack of parts organisers to try to regain some control. :D

                          @Syph007 said:
                          You might be able to change the angle of the pivot for the eblade to get it to sit a little higher in closed position.

                          I'll see how it sits on a blade spring instead of the opener spring - that might be a little higher anyway.

                          @zoidberg said:
                          Process pics are sweet. :tu: What about swapping the e blade and bottle opener? :think:

                          That might work - the e blade nail nick will then be above the awl. I'd need to put a crink in the cap lifter, or use a wider spring and space it from the scale.

                          1 Reply Last reply
                          • Sparky415 Offline
                            Sparky415
                            Posts: 13,000
                            Sparky415 Offline
                            Sparky415
                            wrote on last edited by
                            #6 Quote Reply

                              @kirk13 said:
                              :popcorn: :popcorn: :popcorn:

                              @Zed said:
                              Indeed :popcorn:

                              What they said :salute:

                              1 Reply Last reply
                              • magentus Offline
                                magentus
                                Admin Team
                                Posts: 21,659
                                magentus Offline
                                magentus
                                Admin Team
                                wrote on last edited by
                                #7 Quote Reply

                                  Great work - I love to see in-progress pics.

                                  Keep em coming :salute:

                                  1 Reply Last reply
                                  • lowtech Offline
                                    lowtech
                                    Posts: 4,799
                                    lowtech Offline
                                    lowtech
                                    wrote on last edited by
                                    #8 Quote Reply

                                      So the old girl is getting a makeover. :tu: I like it - All. The WIP pics, getting old worn out SAKs beck into service and modders sharing their knowledge.

                                      1 Reply Last reply
                                      • Reinier Offline
                                        Reinier
                                        Posts: 10,743
                                        Reinier Offline
                                        Reinier
                                        wrote on last edited by
                                        #9 Quote Reply

                                          Too bad it was a Woodsman, but other than that: nice work!
                                          I'm guessing you're not reusing the bail?

                                          1 Reply Last reply
                                          • tommywp Offline
                                            tommywp
                                            Posts: 506
                                            tommywp Offline
                                            tommywp
                                            wrote on last edited by tommywp
                                            #10 Quote Reply

                                              Very cool. For some reason I thought the e-blade would bump into the awl and have trouble sitting opposite. Did you have to crimp the e-blade or do anything special? What else do you think could sit opposite the awl...pruner blade, combo tool, either of the openers?

                                              1 Reply Last reply
                                              • hiraethus Offline
                                                hiraethus
                                                Admin Team
                                                Posts: 6,969
                                                hiraethus Offline
                                                hiraethus
                                                Admin Team
                                                wrote on last edited by
                                                #11 Quote Reply

                                                  @lowtech said:
                                                  So the old girl is getting a makeover. :tu: I like it - All. The WIP pics, getting old worn out SAKs beck into service and modders sharing their knowledge.

                                                  :salute:

                                                  1 Reply Last reply
                                                  • hiraethus Offline
                                                    hiraethus
                                                    Admin Team
                                                    Posts: 6,969
                                                    hiraethus Offline
                                                    hiraethus
                                                    Admin Team
                                                    wrote on last edited by
                                                    #12 Quote Reply

                                                      @Reinier said:
                                                      Too bad it was a Woodsman, but other than that: nice work!
                                                      I'm guessing you're not reusing the bail?

                                                      I'm not a collector or sentimental, so anything's fair game. >:D
                                                      The bail will be going back to the owner - I'm fitting threaded brass pivots with Torx screws.

                                                      1 Reply Last reply
                                                      • hiraethus Offline
                                                        hiraethus
                                                        Admin Team
                                                        Posts: 6,969
                                                        hiraethus Offline
                                                        hiraethus
                                                        Admin Team
                                                        wrote on last edited by
                                                        #13 Quote Reply

                                                          @tommywp said:
                                                          Very cool. For some reason I thought the e-blade would bump into the awl and have trouble sitting opposite. Did you have to crimp the e-blade or do anything special? What else do you think could sit opposite the awl...pruner blade, combo tool, either of the openers?

                                                          It does. They both lie along the scale - so I need to add a spacer or a bend in the blade to clear the awl. Most short tools will fit, but they'll need a tweak to clear the awl too.

                                                          1 Reply Last reply
                                                          • tommywp Offline
                                                            tommywp
                                                            Posts: 506
                                                            tommywp Offline
                                                            tommywp
                                                            wrote on last edited by
                                                            #14 Quote Reply

                                                              @hiraethus said:

                                                              @tommywp said:

                                                              Very cool. For some reason I thought the e-blade would bump into the awl and have trouble sitting opposite. Did you have to crimp the e-blade or do anything special? What else do you think could sit opposite the awl...pruner blade, combo tool, either of the openers?

                                                              It does. They both lie along the scale - so I need to add a spacer or a bend in the blade to clear the awl. Most short tools will fit, but they'll need a tweak to clear the awl too.

                                                              That seems like it would be the hardest part. When you're showing off the mod skills you can't leave out the hardest part! Nice work!

                                                              1 Reply Last reply
                                                              • BASguy Offline
                                                                BASguy
                                                                Posts: 935
                                                                BASguy Offline
                                                                BASguy
                                                                wrote on last edited by
                                                                #15 Quote Reply

                                                                  Really excellent work there. Well done.

                                                                  Sent from my iPhone using Tapatalk

                                                                  1 Reply Last reply
                                                                  • hiraethus Offline
                                                                    hiraethus
                                                                    Admin Team
                                                                    Posts: 6,969
                                                                    hiraethus Offline
                                                                    hiraethus
                                                                    Admin Team
                                                                    wrote on last edited by
                                                                    #16 Quote Reply

                                                                      Worked out what I reckon is the best layout for this now (only a month after I last did anything on this :-[ ):


                                                                      No liners and 2 opener layer springs make for a pretty slim knife and the only mods are a slight tweak to the cap lifter/large flat driver and a little bend in the spring under the awl. All tools easily accessible, nothing blocked by anything else.

                                                                      1 Reply Last reply
                                                                      • kirk13 Offline
                                                                        kirk13
                                                                        Admin Team
                                                                        Posts: 15,955
                                                                        kirk13 Offline
                                                                        kirk13
                                                                        Admin Team
                                                                        wrote on last edited by
                                                                        #17 Quote Reply

                                                                          Looking good :tu:

                                                                          1 Reply Last reply
                                                                          • wmoco Offline
                                                                            wmoco
                                                                            Posts: 116
                                                                            wmoco Offline
                                                                            wmoco
                                                                            wrote on last edited by
                                                                            #18 Quote Reply

                                                                              @hiraethus said:
                                                                              Worked out what I reckon is the best layout for this now (only a month after I last did anything on this :-[ ):


                                                                              No liners and 2 opener layer springs make for a pretty slim knife and the only mods are a slight tweak to the cap lifter/large flat driver and a little bend in the spring under the awl. All tools easily accessible, nothing blocked by anything else.

                                                                              Why no liners? Aestethics, size, weight, access?

                                                                              1 Reply Last reply
                                                                              • hiraethus Offline
                                                                                hiraethus
                                                                                Admin Team
                                                                                Posts: 6,969
                                                                                hiraethus Offline
                                                                                hiraethus
                                                                                Admin Team
                                                                                wrote on last edited by
                                                                                #19 Quote Reply

                                                                                  Size, aesthetics and luck - the small spacer from next to the awl on the donor Electrician is just the right thickness to fit between the sheepsfoot blade and awl if I use the two narrower opener springs. If I used a blade spring for the awl/cap lifter layer and a liner, I'd need three separate spacers on the knife.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Old cross Woodsman into not-quite-an-Electrician mod
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0