Bring it back! (KF4 Appreciatcion Thread)
-
Don't you find it to have a lot of play on the pivot and be very flimsy?
-
@Benner said:
Don't you find it to have a lot of play on the pivot and be very flimsy?I haven't.
It is somewhat thin, but I've always seen that as a good thing for a saw... I've only had good experiences with it. Do you think your pivot pin might be too loose?While we're on the subject, I remember Def's had a little issue with it "springing" over into the awl's way. Does yours do that? Neither of mine do...
-
Think there was a post on here about Marshall's having both PSTs and KF4s. I saw them at one here in Houston. Of course i was broke at the time. >:(
-
Don't you find it to have a lot of play on the pivot and be very flimsy?
I haven't.
It is somewhat thin, but I've always seen that as a good thing for a saw... I've only had good experiences with it. Do you think your pivot pin might be too loose?While we're on the subject, I remember Def's had a little issue with it "springing" over into the awl's way. Does yours do that? Neither of mine do...
It doesn't really appear to be too loose. Everything else seems to be ok. :-\
Mine doesn't get in the way of the awl no.
-
@Defender said:
I have to agree with Bob on that one...It's not really that bad, but it certainly isn't the kf4's strong point, and I too would rather have scissors.
Def
The saw is my least favorite implement on the Kf4.
Kf4 has 4 long slots available for implements, and 3 slots are filled with plain edge blade, serrated blade, and file leaving 1 slot open.
LM chose to fill that slot with a woodsaw, but they could have chosen scissors.
I've never had much enthusiasm for woodsaws on small multis and SAKs - I have difficulty getting much use out of them due to their shortness. Given the choice of what implement to put in that last slot, I'd probably choose scissors over a saw.
It'd be great if LM would bring back the Kf4 and offer:
-current Kfw4 model with woodsaw
-additional Kfs4 with scissors in place of woodsaw.
-
I have to agree with Bob on that one...
It's not really that bad, but it certainly isn't the kf4's strong point, and I too would rather have scissors.
Def
The saw is my least favorite implement on the Kf4.
Kf4 has 4 long slots available for implements, and 3 slots are filled with plain edge blade, serrated blade, and file leaving 1 slot open.
LM chose to fill that slot with a woodsaw, but they could have chosen scissors.
I've never had much enthusiasm for woodsaws on small multis and SAKs - I have difficulty getting much use out of them due to their shortness. Given the choice of what implement to put in that last slot, I'd probably choose scissors over a saw.
It'd be great if LM would bring back the Kf4 and offer:
-current Kfw4 model with woodsaw
-additional Kfs4 with scissors in place of woodsaw.
Here here, I agree entirely! :)
sidebar: and leave the inch/metric ruler etched on the side. Its not used much, but it doesn't take up any space and occasionally comes in handy.
-
The ruler is a big bonus to me. I actually use it quite a lot and it's the only downfall of the Spirit IMO.
-
I added a poll about possible configurations here.
As promised, here's comparison shots of the Charge, KF4, and Surge...

-
...Which I think is pretty good considering the difference in the overall sizes of the tools. :) I personally think the KF4 makes a great hiking/camping tool, partly because of the "large" saw in such a small tool.
I don't have any Vics, Sogs, etc. to compare, but if anyone else wants to take a pic, I'd be interested.


-
any help?
it aint kf4 but same size.
-
@Tarrodemierda said:
any help?
it aint kf4 but same size.Thanks. Nice to see the sizes of so many different tools. :) I aslo curious how the saws stacked up, but I guess an S2 won't help us much there... :-\
-
If the KF4 had scissors instead of a saw, then a Farmer would be the perfect complimentary EDC.
-
Good point, gtg! That would be an excellent combo

A stock KF4 and a Soldier would also be a good combo. You wouldn't have scissors, but you could get a lot done with those 2 tools.
I think I would actually prefer a stock KF4 and a "Soldier with scissors". I don't think there's ever been a 93mm with scissors though, has there? And please don't tease me with pics of some amazing mod I'll never have! :D
-
@NeitherExtreme said:
...Which I think is pretty good considering the difference in the overall sizes of the tools. :) I personally think the KF4 makes a great hiking/camping tool, partly because of the "large" saw in such a small tool.I don't have any Vics, Sogs, etc. to compare, but if anyone else wants to take a pic, I'd be interested.

Here ya go Luke [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/S6300515.jpg)]
](http:// Side by side with the Huntsman .KF4 is almost 1cm shorter & only 1/2 cm wider (comparing knives at their widest points) :o [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/S6300535.jpg)]
](http://![) Group hug Swisstool , Supertool ,Juice & Surge . Top too bottom :D -
@NeitherExtreme said:
Sounds like there's a few more fans out there than just me! :)I was guessing some people would ask for scissors, as they seem to be about the "favorite" implement that the KF4 lacks. Although I love the current setup, I'd also be happy to see the serrated blade switched with scissors...
I'm kinda surprised by the lack of enthusiasm for the saw... I can understand not wanting a MT-sized saw in general, but IMO the Juice saw is a standout feature on the KF4. I've used it fairly often, both on wood and drywall, and I've been very happy with it. Also, even though the KF4 is so much smaller, the saw has the same cutting length as the Wave, Charge, and Surge. :o I think it's a great design. :) The saw and awl combo make a great drywall pair by the way.
I think I'll take a pic comparing the saws and post it here tommorrow. :)
I hope I did not beat you to the punch Luke , but in the short time I have had my Kentucky Fried Juice I have got a bit attached to it . Initially the lake of scissors & BOTTLE opener was a major concern but I have gotten over that. I quite like the saw option in such a small Tool & all the talk about it got me thinking. [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/S6300564.jpg)]
](http:// The Juice's saw is actually longer than the Surge's :o But the Surge saw is a bit beefier . [(http://i291.photobucket.com/albums/ll287/multimat426/multitools/S6300568.jpg)]
](http://![) I think when it comes to serious sawing you need a proper saw but in a pinch I would be happy to use any of the above tools , I just need a beer opener on my KF4 :D -
Thanks MultiMat!! Those pics are awesome.
Thanks for doing that. :)I think its a really strong point of the KF4 (and Juices in general) that even though they are smaller, the "working" portion of the files and saws are really quite comparable to the larger tools. :) Even the Swisstool only has one or two more teeth on the saw. :o
@MultiMat said:
I think when it comes to serious sawing you need a proper saw but in a pinch I would be happy to use any of the above tools...I agree entirely. MT saws aren't for "real" work, but they sure can be handy for small jobs. :)
-
A lot of people seem to want scissors on the KF4. So what does everyone think about the XE6? Gives you scissors and more. Weighs 25g more.
Also wondering if anyone has ever considered modding the KF4 or EX6 to get that configuration...
-
@max6166 said:
A lot of people seem to want scissors on the KF4. So what does everyone think about the XE6? Gives you scissors and more. Weighs 25g more.Also wondering if anyone has ever considered modding the KF4 or EX6 to get that configuration...
Part of the KF4's appeal (IMO) is the fact that it is a great size to hold and for me has nearly everything I need and nothing I don't. The XE6 adds a lot of bulk and tools that I am not so keen on.
-
@NeitherExtreme said:
Thanks MultiMat!! Those pics are awesome.
Thanks for doing that. :)I think its a really strong point of the KF4 (and Juices in general) that even though they are smaller, the "working" portion of the files and saws are really quite comparable to the larger tools. :) Even the Swisstool only has one or two more teeth on the saw. :o
I think when it comes to serious sawing you need a proper saw but in a pinch I would be happy to use any of the above tools...
I agree entirely. MT saws aren't for "real" work, but they sure can be handy for small jobs. :)
No worries cobber . I always thought the Juice line was a bit of a joke , but all the talk about the KF4 lead me too getting one. I reckon they are a "SUPER" pocket knife .A SAK with proper pliers :o :D , I think if you put a red Victorinox on one micky d would be raving about them
:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login