The Mega84
-
@50ft-trad said:
Very clever with the Phillips

Thanks Tommy
It took a while to figure out how to make it work, but it took a lot longer to get the right donors together :DYa very nice!
Its funny I am tackling the same issue right now on a 91mm job that needs both backside phillips and corkscrew. The problem is I have less space to fit the phillips, so I milled it flat on each side, (kind of looks like a flat leatherman phillips now) but it should fit in space I have for it now. Im using 2x saw backsprings with backtool cutouts to house the phillips. It should work but it hasnt gone together yet.
-
@50ft-trad said:
Very clever with the Phillips

Thanks Tommy
It took a while to figure out how to make it work, but it took a lot longer to get the right donors together :DYa very nice!
Its funny I am tackling the same issue right now on a 91mm job that needs both backside phillips and corkscrew. The problem is I have less space to fit the phillips, so I milled it flat on each side, (kind of looks like a flat leatherman phillips now) but it should fit in space I have for it now. Im using 2x saw backsprings with backtool cutouts to house the phillips. It should work but it hasnt gone together yet.
Cheers Bob
I was originally hoping to get away with not having to add that second liner, but as it happens they were needed anyway for access to the nail nicks on the cap lifter and nail file. They're still tight, but doable with my nails, and would have been impossible with one liner. The awl worked out well too with just a sliver ground off the kick 
Are you using an inline Phillips for that mod, or have you milled it offset? I wouldn't imagine you could afford to lose much off the tang side of a backspring Phillips

-
Very nice Al!

-
Cheers Tom
I hope to have the Mega84 v1 peened up and in the pocket today. Might even have a look at one of the other mods too :) -
very cool Al,look forward too seeing it finnished 
-
Hmmm.... the lack of a vice is hampering my abilities to get one end of the pin peened before building it up

I tried just standing the pins on end on my mini anvil, but that just bent the pins. I then tried using a G cramp on the garden fence, but that didn't work either - not secure enough. I think I'm going to have to try NOT pre-peening, having excess on both sides, and then cropping/filing/peening both sides together. That'll be interesting....
@Zed said:
very cool Al,look forward too seeing it finnished 
Thanks Paul

-
Hold it with the drill.
-
Nice one Zoidie!!!!

That actually works BETTER than a vice. Drill tucked under left arm, turning chuck with left hand, and rapidly hitting with hammer in right hand whilst slowly turning the chuck. It's like a mini GFM forge :D Perfect!
I've had to shorten the pins a bit first so there's not much stuck out. Hopefully there's still enough to work with :ahhh
-
Hang on.... this is a hammer drill.....

I wonder....
-
BRILLIANT!!!!!!Grip pin in chuck, set to hammer, and "drill" the side of an axe head at a slight angle! Just enough pressure to get the hammer action to kick in, but not enough to bend the pin. A perfectly pre-peened pin in seconds :D
-
@50ft-trad said:
BRILLIANT!!!!!!Grip pin in chuck, set to hammer, and "drill" the side of an axe head at a slight angle! Just enough pressure to get the hammer action to kick in, but not enough to bend the pin. A perfectly pre-peened pin in seconds :D
WE DEMAND A VIDEO! :ahhh
:D
-
Now I need to come up with a concave "drill bit" for finishing off the other side when I've built it up >:D
-
I really can't believe how well that works. They've actually slightly "over peened" and don't quite seat in the bushings, so I'm just tickling them up with a file. It actually gives a nice domed and burnished finish.
Alox modders take note!
-
@50ft-trad said:
BRILLIANT!!!!!!Grip pin in chuck, set to hammer, and "drill" the side of an axe head at a slight angle! Just enough pressure to get the hammer action to kick in, but not enough to bend the pin. A perfectly pre-peened pin in seconds :D
WE DEMAND A VIDEO! :ahhh
:D
Hear, hear!

I was referring to a 91mm metal saw earlier; I know 84mm ones are hard to find. Besides, newer ones are better ;)
I'm probably too late for this but what if you turned the pruner balde to a wharncliffe, a sheepsfoot or a bevel point? More function then. >:D :)
It was your preference of cellidor that I recalled, then.
Now you've got me thinking about a mod I had in mind... Will you be modding a Wenger next by any chance? :ahhh
-
@50ft-trad said:
BRILLIANT!!!!!!Grip pin in chuck, set to hammer, and "drill" the side of an axe head at a slight angle! Just enough pressure to get the hammer action to kick in, but not enough to bend the pin. A perfectly pre-peened pin in seconds :D
WE DEMAND A VIDEO! :ahhh
:D
Hear, hear!

I was referring to a 91mm metal saw earlier; I know 84mm ones are hard to find. Besides, newer ones are better ;)
I'm probably too late for this but what if you turned the pruner balde to a wharncliffe, a sheepsfoot or a bevel point? More function then. >:D :)
It was your preference of cellidor that I recalled, then.
Now you've got me thinking about a mod I had in mind... Will you be modding a Wenger next by any chance? :ahhh
No vids, sorry.
I was tempted to use the MFV blade for turning into a wharncliffe actually. Unfortunately, it's only 2.0mm tang thickness and I need the 2.4 due to the awl tang thickness.
Yes, Wenger may well be next, but that's (hopefully) a MUCH simpler project :)
-
84mm saw springs are a PITA >:(
-
Awl spring is protruding a little, which means the Phillips is sitting high. I've marked it up with a sharpie marker to see if it can be reprofiled without compromising the spring under the cap lifter

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
