Off-Brand Challenge - ETHEREALICER - Böker City Tool / SWIZA D04
-
Comparison shots of the Böker City Tool Blade with other MTs:
Be careful, both Charge and Surge are 1cm back!
The blade without tool is from a MP-600...



-
Bit of a scare today, the scissor spring was incredibly weak (see how much play it has in the picture). Anyway, figured out what the problem was. When I took off the pocket-clip yesterday I put the screw back in and apparently tied it to tightly. Loosing that screw restored the scissor spring. So, while everything is good again I dislike the fact that the clip is on that critical screw.

-
Small screw-driver VS IKEA
Have you ever been offered one of these knife sets that come in a fake-leather briefcase. The vendor will claim that the set commonly costs more than a thousand buck but due to some wild reason you have the once in a lifetime chance to get the set for 50! Truth is, the knifes are not even worth that they are complete and utter garbage. Sadly the rescue-blade sort-off reminds me of those knifes (it also has the same cross-section, see image below) making this the SAK-alike with the best and worst blade :P
But what about the screw-driver at its tip?
Today was the first time I used it to tighten a screw on my IKEA closet. I did not want it to close on my finger so I held it a bit different than I usually would... promptly I slipped off. Immediately, I spotted traces of wear on the driver. So, just for exercise I tightened 7 more.
In total I tightened 4 on the left side, using my right hand on this fairly easy challenge.- I slipped off 3 times in the process
I also tightened 4 on the right side, using my left hand
- Slipping off 9!!! times
- Having the driver collaps 3 times :ahhh
I had low expectations for this tool and sadly I still got disappointed

Fake "action" shot
After first screw you can already see abuse on the screwdriver
After only 8 screws it looks quite bad


-
- YouTube
Auf YouTube findest du die angesagtesten Videos und Tracks. Außerdem kannst du eigene Inhalte hochladen und mit Freunden oder gleich der ganzen Welt teilen.
(www.youtube.com)
-
I would like to point out that the large screwdriver has done more work and harder work without showing any signs of wear! So, the large flat seems to be made of tougher material.
-
AND NOW SOMETHING COMPLETELY DIFFERENT
Well, maybe not: SWIZA D04 or as I call it the Do-oh-fer :D (doof means stupid in German, doofer means more stupid)
Lets hope the knife is more exciting than its name... so, first impressions.The very first thing I saw was that it said "dishwasher safe up to 80°", now I'm properly excited. The tool is grippy and with its curve quite comfortable. At least on the scales there are no hotspots. It does however not feel as sturdy as the Boker or a Victorinox, although that is just based on the feel so utterly irrelevant.
Its got a locking blade, awl, large-screwdriver/cap-lifter, small-screwdriver/can-opener, back-layer Phillips and tweezers in the scales.
The BLADE
Typical SAK-like spearpoint blade. As for the steel I can only say that it feels soft and bends much more than a Vic blade. Not my favorite shape, also not a huge fan of the hole. The blade locks and is unlocked by pressing the cross on the scale (I wonder how long that plastic there will hold up)The AWL
I like that they put an awl in the blade layer.
Shorter than the pioneer awl. I'm a bit worried about that prominent rim.



-
Thank you for the first impression review!

-
Next up is the "opener-layer"
Weirdly enough it's the can-opener that is super beefy (thicker than the Victorinox cap-lifter) and the cap lifter that is quite thin (thinner than the Victorinox cap-lifter)
Shockingly, the cap-lifter looks like a cap-lifter... It locks strongly at 90° and 180°, feels very truth-worthy at least concerning back spring retention.
This must be the ugliest tool after the Skeletool, but at the end of the day, this is not a beauty contest, so lets wait and see it perform. What I noticed however is, that the spring is much weaker than for the cap-lifter, it feels not good (probably due to the fact that the 3rd pin is much closer to the cap-lifter pivot).



-
-
Backlayer Phillips
No Sir, I do not like Sir. Funny enough I only today found out that I don't own a single Vic with back-layer Phillips
It's slightly (maybe 1mm) longer than the Vic CS... whatever back-layer tool who cares... :P
Yay, it has Wenger style tweezers in its scales.
They not only look better than its Vic brethren, they feel more solid and stronger. The tip is slightly angled which gives you a slightly pointy and a flat grip. Also, initial tests by my fiancee confirm that they perform better.


-
-
Nice one Eth.

-

Waiting for my D02 to arrive.Sent from a device made from star dust using tapatalk
-
How sharp is sharp enough
Task 1 was to cut some onions... if the blade is sharp = no tears, if not, I will be crying like a baby...
So far so good.
The curved handle and the angled blade takes a bit to get used to.
All done, this knife needs sharpening, I'm all teary :'(


-
the holes on the tools remind me of SOG....
how do you get them to ship out of Switzerland? there shipping explanation reads weird
-
-
More cutting... it supposedly has the longer blade than a Vic but it does not feel like it

Also, its not made to cut cheese




-
Grath ordered one :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login