Wanted: Detailed Diagram of the 91mm Plus Scales
-
Am considering ordering more silky oak, as I want a pair of chopsticks out of that wood. And want to use tung oil to finish them. Favorite pair of chopsticks is 9.5" long, Thai style in rosewood, tapered down to 3mm. Only thing is I have no wood lathe/turner.
Have a few sets, but when they taper to 4+ mm that is too thick and awkward for me to use. Feels like I am using pencils (eraser end) for eating utensils.
Top is my favorite set. Below them are backups with an ornate twist carving.

@PTRSAK said:
more timber fromm the same supplier... Brown Mallee BurlI am seriously looking forward to getting a SAK scaled in this.

Interesting wood. Wonder how Zebra wood is? Seems to me when carving the edge it really brings out the wood effects more.
Saw an outfit here in the states with several wood samples perfect for SAK scales, but the way they had cut the wood left a lot to be desired. Was more like a package of 'Oops cuts'.
Turning Timbers seems to know how to cut the wood the correct way!

-
Australian Turning Timbers has some attractive blanks up again. If only had more money to work with, and a shop. Might have to wait till Spring so can carve outside.
Coolabah Burl
Birdseye Red Gum
African Wenge
Brush Box
Fiddleback Queensland Narrow Leaf Wattle - Am liking this one!

Lots more.
-
Heh, now I want to carve a small eating spoon from wood. Shouldn't be too hard, right?

-
Had to, was my post anyhow. :D
Now if I could remember where I put the first SAK post where the forum helped me for the most part, and I decided on a Climber.
-
@Outback in Idaho said:
For the pin, having a recent issue with the pin getting caught on the corkscrew, had come up with the idea of putting a small magnet into the handle. This would also help keep the pin magnetized & held into place since my Climber has aluminum scales.Debating between these two, unless someone else has another option. Have tried the flexible magnet inside the current plastic scale and it just does <u>not</u> do a thing. Not enough magnetic power there.
15 PC Neodymium Magnets N42 Dia 2X2mm Rare Earth NdFeB Magnets

50 Pieces N42 Neodymium Magnets Dia 3mm x 1.5mm Thick

Comments, suggestions, or...
?I know this post had been out for a while now, but I had just come across this. Not to sure If it has been answered as well.
A friend of mine suggested if the straight pin comes loose, try applying a bit of silicone sealant in the hole. So I tried and walah, mo more loose straight pins...

Sent from my iPhone using Tapatalk
-
The idea of the magnets was to a polarity on the needle so it would point north if ever needed. The magnets were a dickens to get in there and aligned.
As much effort I went through to get the needle aligned North and South something changed... the North end was supposed to be the pointed end. I quadruple checked and verified the magnet placement was correct. But... when I tested it, the head of the pin became North, not the prickly end. Not sure what changed its polarity there.

The pin doesn't slide out on its own, one needs to use their fingernail. -
@Outback in Idaho said:
The idea of the magnets was to a polarity on the needle so it would point north if ever needed. The magnets were a dickens to get in there and aligned.As much effort I went through to get the needle aligned North and South something changed... the North end was supposed to be the pointed end. I quadruple checked and verified the magnet placement was correct. But... when I tested it, the head of the pin became North, not the prickly end. Not sure what changed its polarity there.

The pin doesn't slide out on its own, one needs to use their fingernail.Ah... Interesting...
Sent from my iPhone using Tapatalk
-
If I had it to do all over again, I'd just get some silky oak blanks cut like what WoodMan did, then cut the slots out by hand or something, and epoxy it back on and forego the magnets. I don't have the materials to cut scales, but I can order the wood from Australia or over here in the USA. Could have to get another Vic emblem too and try a different method of securing it in there.
Might give it a go some day - or not.
-
Hi, new to this site. maybe I can help out with ANY CAD files you need. I'm a Mechanical Designer (Engineer). I have exceptional knowledge in Solidworks and Pro Engineer (Creo). If someone has a good DXF or DWG file or can give me some dimensions I can model a 3D of the scales or whatever you want. Otherwise I will have to try and take apart a knife and measure the crap out of it.
-
3D STL files for 58 and 91 mm scales are available for downloading on Thingiverse.com.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
