Swisstools the different models
-
@carl said:
The "General" forum is discussing the use of "soft" metal by Victorinox in the Swisstool.- Is bending a common problem with the tools?
- Has anyone stripped a driver head? I stripped a phillips head on a Gerber. It went smooth after one use.
- Does the straight blade go dull quickly?
- Does the wire cutter go dull quickly?
I know a little about swisstools so I will try and help
- No its not common , In 9 years of owning swisstools I've bent two flat screwdriver /bottle operners . The first time was a slight bend when I had the handles open at 90 degrees for extra leveradge and it was replaced with a new one . The second was when I wrongly used it as a pry bar and bent it quite bad , straightened it with a spirit and its been fine ever since . You must understand that I used as much force my 15 stone could put behind it . They didnt bend easily .
2 ) To be honest the phillips on the Swisstool can slip if you dont push hard enough and can lead to rounding off , its not as bad as some people make out .
3 ) Its the same metal as any other Vic SAK , Can be sharpened to hair shaving sharpness very quickly because its quite soft ( and rust resistant ) not bad at edge holding but the secret is to keep it nice and sharp , a little sharpening often . Compared with super steels like S30V that holds a superior edge but is a b*tch to sharpen as its so hard .
4 ) No not at all , have a search around these forums and theres a couple of vids I done on cutting coat hangers and barbed wire with no damage at all to the cutters .
Hope this helps
Dunc
-
I think Dunc's response is spot on with what others have said.
I think some people have touched up the phillips head a bit to get around the problem too.
Don't forget the phillips on the can opener too! :D
-
One more question: Does anyone do any custom work/mods on Swisstools?
-
Why would you mod a perfect tool? ::) :D
Except for a pocket clip... really...
-
One more question: Has the side play on the head been fixed? I handled an older Swisstool and the play was more than i expected. I know it doesn't affect function but...
-
My 05 is tight as a drum mate :)
-
I have a ton of SwissTools now and only two of them have plier pivot play! An 05 RS and X. :)
-
Two '05 Swisstools? Those are recent models. Do they have the wider/taller head and the smaller pivot pin?
-
@carl said:
Two '05 Swisstools? Those are recent models. Do they have the wider/taller head and the smaller pivot pin?The pin really is only slightly smaller if at all, and yes they are a lot beefier too :)
To be honest mate, just get one. Forget what all the naysayers say, there a great, and nigh on indestructable tool :)
-
I'm not a naysayer!
;) :D I really like the SwissTools! -
@Micky d said:
Two '05 Swisstools? Those are recent models. Do they have the wider/taller head and the smaller pivot pin?
The pin really is only slightly smaller if at all, and yes they are a lot beefier too :)
To be honest mate, just get one. Forget what all the naysayers say, there a great, and nigh on indestructable tool :)
I bet I could break one. Destruction is my thing, when the mood takes me.
-
@Micky d said:
Two '05 Swisstools? Those are recent models. Do they have the wider/taller head and the smaller pivot pin?
The pin really is only slightly smaller if at all, and yes they are a lot beefier too :)
To be honest mate, just get one. Forget what all the naysayers say, there a great, and nigh on indestructable tool :)
I bet I could break one. Destruction is my thing, when the mood takes me.
I did say nigh on :D
Nice sigline BTW :D
-
A quote I found regarding metal hardness.
VICTORINOX is the world leader of Pocket tools (Multi-Tools and Pocket knives). For every activity, be it professional, in the home or during leisure time, there is a need for excellent tools and cutting implements. All Victorinox knives are high carbon, stainless, first grade, A-quality steel. They are tempered to a 55-56 HRC hardness for optimum edge retention. The wood saws, scissors and nailfiles have a hardness of RC 53, the screwdrivers, tinopeners and reamers RC 52, and the corkscrews and springs RC 49.
-
Sound's right to me :)
-
I'm guessing that was from a Vic website / seller, right? :D
-
I'm not saying it's wrong, but the expression "VICTORINOX is the world leader of Pocket tools (Multi-Tools and Pocket knives)" didn't come from a Gerber site did it? :D
I've no reason to doubt that the stats are right, but that bit is a just a tad biased isn't it?
-
@DaveK said:
I'm not saying it's wrong, but the expression "VICTORINOX is the world leader of Pocket tools (Multi-Tools and Pocket knives)" didn't come from a Gerber site did it? :DI've no reason to doubt that the stats are right, but that bit is a just a tad biased isn't it?
I would say they were the world leader in pocket tool's, maybe not so much MT's, but there enourmous Sak range more than offset's there relative lack of MT's imo :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:D