Possible cheap pivots.
-
Un-derailing for a minute... I have some M2 taps on order because the thread only goes in about 5mm from each end and I bought quite long standoffs. Once they are cut down to length it will lose the thread from one end.
First trial will be done once they arrive.
I should order some more carbide drills too.
-
As a note, these pivots all take 2/56 screws. All thought they are thin, this problem is address by using screws that are as long as the pivots.
-
Any news on how they are going yet or still waiting on stuff to come in

-
Taps arrived but now I'm 120km away from home for the weekend. The screws I have are long enough to meet in the middle of a 5 layer alox.
-

Fitting. The size is perfect. I would have had it back together but my screw holes for the clip was stripped. I'm trying jb weld first before I go to a insert to see it that's strong enough to hold. More pics will follow later today if my health holds up.
-
@PTRSAK said:
Taps arrived but now I'm 120km away from home for the weekend. The screws I have are long enough to meet in the middle of a 5 layer alox.I've been thinking about this for a similar project. Although I think a pivot fully filled with screw initially seems like a good idea I'm less sure after pondering the mechanics of it because...
[list type=decimal]-
If the screw faces actually meet then they are trying to pull the pivot apart at the join surface.
-
If they almost meet then any thermal or movement stress is working on just the unfilled section (because it is most elastic)
Neither of these is likely to be an immediate problem, but over time fatigue may cause a split.
The other option is having a reasonable length empty section between the screw faces, and as long as the wall thickness is sufficient to not deform when opening / closing / using tools then I'm thinking this may be the most durable configuration as the longer empty section can absorb more movement. But I'm not a materials engineer so am unsure ???.
-
-
@Little Tinker said:
Taps arrived but now I'm 120km away from home for the weekend. The screws I have are long enough to meet in the middle of a 5 layer alox.
I've been thinking about this for a similar project. Although I think a pivot fully filled with screw initially seems like a good idea I'm less sure after pondering the mechanics of it because...
[list type=decimal]- If the screw faces actually meet then they are trying to pull the pivot apart at the join surface.
- If they almost meet then any thermal or movement stress is working on just the unfilled section (because it is most elastic)
Neither of these is likely to be an immediate problem, but over time fatigue may cause a split.
The other option is having a reasonable length empty section between the screw faces, and as long as the wall thickness is sufficient to not deform when opening / closing / using tools then I'm thinking this may be the most durable configuration as the longer empty section can absorb more movement. But I'm not a materials engineer so am unsure ???.
If the pivots are cut to the correct length then once tightened it solves this problem. Also use blue loctite so they don't move once tightened.
-
@Little Tinker said:
Taps arrived but now I'm 120km away from home for the weekend. The screws I have are long enough to meet in the middle of a 5 layer alox.
I've been thinking about this for a similar project. Although I think a pivot fully filled with screw initially seems like a good idea I'm less sure after pondering the mechanics of it because...
[list type=decimal]- If the screw faces actually meet then they are trying to pull the pivot apart at the join surface.
- If they almost meet then any thermal or movement stress is working on just the unfilled section (because it is most elastic)
Neither of these is likely to be an immediate problem, but over time fatigue may cause a split.
The other option is having a reasonable length empty section between the screw faces, and as long as the wall thickness is sufficient to not deform when opening / closing / using tools then I'm thinking this may be the most durable configuration as the longer empty section can absorb more movement. But I'm not a materials engineer so am unsure ???.
Im not an materials engineer (yet >:D) but I do happen to be studying that subject right now, (for whatever thats worth.)
Your first point is quite valid. If the screws meet at the middle, they could begin to push against each other, compromising the threads of the pivot, and leading to a failure. However, this is pretty easily avoided with careful measuring, and leaving a small gap.
Thermal expansion isnt really a problem. If your tools are experiencing the kind of thermal fluctuations that could induce a sudden failure of the pivot due to changes in size, the heat treatment of your tools is probably ruined (and if that happens, your whole SAK is basically useless). Not to mention your liners, springs and tools would be expanding/contracting at roughly the same rate as the pivots. Dont drop your SAK into a campfire, and it should be fine.
As far as the universe is concerned, a 2.5mm solid brass rod functions the same as a 2.5mm brass pivot with screws almost meeting in tthe middle. So any issue you would see with these pivots (provided they were manufactured and installed correctly) would also be seen in a standard SAK. The small gap between the screws would be sufficiently supportes by the pivot walls and screws on either side of the gap
-
Pleased to hear we've given it some thought.

I'll also press on then :D.
-
-
Looks glorious

-
Necro report.
The Green Aloxplorer (pictured above) is as tight as the day it was born 2 & 1/2 years ago.
Sure, there are better screwed pivots out there, but not at less than 50c for a whole knife.
-
Hey,
So this is funny. I found these circuit board standoffs independently, bought them about 2 months ago but haven't don't the mod yet. I then found this thread the other day.
Glad to see that it all worked out. I bought some long pivots 23mm. And I found that the threads did not go all the way through. I had to tap from each end to about 1/2 way. Did you experience this?
I also changed to use hex screws instead of torx.
Lastly did you use the same pivots for the middle pivot and drill it out? Or did you thin the pivot?
Very curious about this.
-
So this is funny. I found these circuit board standoffs independently, bought them about 2 months ago but haven't don't the mod yet. I then found this thread the other day.
Glad to see that it all worked out. I bought some long pivots 23mm. And I found that the threads did not go all the way through. I had to tap from each end to about 1/2 way. Did you experience this?
I also changed to use hex screws instead of torx.
Lastly did you use the same pivots for the middle pivot and drill it out? Or did you thin the pivot?
Very curious about this.
Yes, the thread was only about 5mm deep from each end so I tapped it the rest of the way.
The screws I used are in hex head as shown in the photo above and I drilled out the centre hole to 3mm from the original 2.5 so I could use the same pivots in all 3 holes.
-
Sorry to revive this old thread, but I'd like to know how these hold up over time. I'm considering using brass M2 standoffs as pivots for 93mm SAKs. I've already used them on a Leatherman Juice mod but I'm worried by the much stronger 93mm springs. To those of you who made 93mm SAKs with them, do you have any update for the rest of us?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
