I Recently Converted My Alox Mod to Torx
-
Very cool.

You got lucky with being able to use 3mm pivots I think... :) -
Awesome! This is one of my dream mods and will hopefully be made in the future. This thread will work for reference so thank you!!
It's not failure if you learn something from it
-
@Pablo O'Brien said:
Very cool.
You got lucky with being able to use 3mm pivots I think... :)Got lucky? Why go to all the trouble of drilling out the tools to 1/8" if 3mm pivots are available?
-
@Pablo O'Brien said:
Very cool.

You got lucky with being able to use 3mm pivots I think... :)Got lucky? Why go to all the trouble of drilling out the tools to 1/8" if 3mm pivots are available?
:D
Indeed... 3mm pivots don't seem to be common. :D -
Thanks Guys

The pivots were part of a deal I had with Tattoosteve99... An awesome guy and friend... A good person to deal with...
Sent from my iPhone using Tapatalk
-
-
Awesome and timely post.
Well done - l believe your approach is the simplest l have seen.
I too want to build an Alox with this exact layout.
I've been holding off on buying the 1/8" pivots from the recommended place as they have a $US 50 minimum order (not including postage) for overseas buyers.
A few questions;
-
What is the thread size of the torx screws and where did you buy them from? Are they metric?
-
Any idea of the source of the pivots?
-
l thought l read somewhere on this site that you have to counterbore the inner surface of the scales slightly for the pivots - l believe this is so that the pivots take the load rather that the screws? Is it OK not to do this?
Cheers
George
-
-
@george1 said:
Awesome and timely post.Well done - l believe your approach is the simplest l have seen.
I too want to build an Alox with this exact layout.
I've been holding off on buying the 1/8" pivots from the recommended place as they have a $US 50 minimum order (not including postage) for overseas buyers.
A few questions;
-
What is the thread size of the torx screws and where did you buy them from? Are they metric?
-
Any idea of the source of the pivots?
-
l thought l read somewhere on this site that you have to counterbore the inner surface of the scales slightly for the pivots - l believe this is so that the pivots take the load rather that the screws? Is it OK not to do this?
Cheers
George
Hi George,
I wouldn't be able to answer no.1 as I don't know... like I mention above, I source the pivots and screws from Tattoosteve99...
I didn't counterbore the inside scale holes as all of the pivots ends goes through the scale holes... This I forgot to mention above...
Sent from my iPhone using Tapatalk
-
-
Forgot to mention that the screws I had were T6... Though some may come in T8?

I was about to ask that, thanks.

Imagine if SAKs came with torx screws. Man, the hours of fun we would have had.
That's for sure...

Sent from my iPhone using Tapatalk
-
Thanks for this thread jaya
I had always wondered about the countersinking part
A very straight forward explanation and great pics to go with it
I may try this someday if I can source the parts needed
Maybe a Farmer X with a file and an electrician blade instead of the opener
:DSome of the way the mod goes just hadn't occurred to me, thus why I wanted to see the process

Excellent thread

-
Nice reference for those looking to attempt this mod.

-
Where did you find those torx screws/pivot barrels?
Edit: just read all replies... nvm
-
Thanks Poncho and Aloha007...
:saknight:Sent from my iPhone using Tapatalk
-
Here's an illustration of how the torx and pivot looks like... at least on my mod... as the diameter of the scale pivot holes are just right for the barrels, and there is enough length for the barrel to go through the scale, counterbore wasn't required...

Maybe counterbore would be required for 1/8" barrels?
Sent from my iPhone using Tapatalk
-
Very cool thread

-
@Mechanickal said:
Where did you find those torx screws/pivot barrels?
Edit: just read all replies... nvm
I just don't know whether Steven sells them to anyone who asks? Or mine were just extras lying around...
Sent from my iPhone using Tapatalk
-
-
@jaya_man said:
Here's an illustration of how the torx and pivot looks like... at least on my mod... as the diameter of the scale pivot holes are just right for the barrels, and there is enough length for the barrel to go through the scale, counterbore wasn't required...
Maybe counterbore would be required for 1/8" barrels?
Sent from my iPhone using Tapatalk
Great sketch - shows the arrangement nicely.

A couple of points to add, from my experience of similar mods (using 3mm brass pivots on all three points):- cut the pivots as long as you possibly can. The more of the pivot that sticks into the scale the better. I assembled the knives onto longer plain rod, measured the overall thickess then subracted 2.5mm to get the final pivot length.
- countersink the ends of the pivot barrels if you can too - this allows the pivots to be longer and have more engagement with the scales for better snap.
- Make the countersinks in the scales as shallow as possible - again, to maximise the overlap between the pivot and the scale.
The screws I used were metric M2x0.5mm with countersunk T6 heads, but I guess the ones Steve used are imperial/standard 2-56.
-
Here's an illustration of how the torx and pivot looks like... at least on my mod... as the diameter of the scale pivot holes are just right for the barrels, and there is enough length for the barrel to go through the scale, counterbore wasn't required...

Maybe counterbore would be required for 1/8" barrels?
Sent from my iPhone using Tapatalk
Great sketch - shows the arrangement nicely.

A couple of points to add, from my experience of similar mods (using 3mm brass pivots on all three points):- cut the pivots as long as you possibly can. The more of the pivot that sticks into the scale the better. I assembled the knives onto longer plain rod, measured the overall thickess then subracted 2.5mm to get the final pivot length.
- countersink the ends of the pivot barrels if you can too - this allows the pivots to be longer and have more engagement with the scales for better snap.
- Make the countersinks in the scales as shallow as possible - again, to maximise the overlap between the pivot and the scale.
The screws I used were metric M2x0.5mm with countersunk T6 heads, but I guess the ones Steve used are imperial/standard 2-56.
Ahhh... more helpful tips for me... I will need it for future mods...
Thanks H :saknight:

Sent from my iPhone using Tapatalk
-
Great thread, and very useful

Going back to the original motivation for a moment though, are we sure that it's the brass that's not up to the job. If the pins need repeening, they may be stretching, OR the peened heads may just be "settling" in the holes. I had this happen on one of my mods - everything was tight, but it became a little sloppy with gaps between layers without doing much work. The pins weren't stretching, but the peened heads were pulling in slightly. It may have been that when I was peening, the knife was adequately supported but not the pin itself, and this may have floated slightly when peening the second side.
Hopefully that makes sense

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
