Swisstools the different models
-
Lost out on my first ebay bid for an X but won the next one for a CS. The CS turned out to be actually cheaper. Can't wait to get it - of course I'll inspect it thoroughly to make sure its not used or from older stock. The dealer had a good rating so I don't expect any problems.
-
@carl said:
Lost out on my first ebay bid for an X but won the next one for a CS. The CS turned out to be actually cheaper. Can't wait to get it - of course I'll inspect it thoroughly to make sure its not used or from older stock. The dealer had a good rating so I don't expect any problems.Good on ya mate, you won't regret it

-
Got my CS yesterday - its gorgeous - including the leather case. All the tools have very little or no play - the plier pivot pin has very little play also. When any tool is deployed, the play at the attachment point to the handle is much tighter than on an as-new early model ST I handled a while back. There was a video on this forum about a year ago showing the amount of end-play - my new up-to-date ST-X has no play or almost none on all of the tools. Vic must have addressed this issue on the newer models. Anyway, since this is my Christmas gift from my wife, it goes back in the box until the early am hours of 12-25-08. can't hardly wait!
-
@carl said:
Got my CS yesterday - its gorgeous - including the leather case. All the tools have very little or no play - the plier pivot pin has very little play also. When any tool is deployed, the play at the attachment point to the handle is much tighter than on an as-new early model ST I handled a while back. There was a video on this forum about a year ago showing the amount of end-play - my new up-to-date ST-X has no play or almost none on all of the tools. Vic must have addressed this issue on the newer models. Anyway, since this is my Christmas gift from my wife, it goes back in the box until the early am hours of 12-25-08. can't hardly wait!Oooh, that's got to be a terrible tease, knowing a SwissTool is so close but not able to play with it! >:D
-
Its called "Will Power".
-
-
The ST is great but the small screwdriver seems a bit too small. I wish all the flatblades were a bit larger. Most people I know of deal with medium to large flat blade screws.
-
I have a Swisstool X and i love it.
Kinda off topic but where the heck did the multitool.org comparative weight chart go?
I remember you used to be able to easily find it on the home page but i just looked and looked (even did a search) and can't find it.
Seems kinda silly to have to wade through a text review to just find out simple facts like weight.
The chart i remember was pretty useful, is it still here (somewhere)?
Anybody have a link? -
Nevermind found it down a few layers in the Multi-tool Encyclopedia section
https://wiki.multitool.org/tiki-index.php?page=Comparative+Multitool+Weight+Chart -
Strange the search engine couldn't find it, i found it by accident, lol!
-
Well I'm glad you helped yourself then mate :D
-
@Micky d said:
Well I'm glad you helped yourself then mate :D:D Rather an obliging fellow that one ::) :D
-
i dont know id be happy with tools at the hardness they ar eit is soft, but the blade is thin andyou can push it through things if it is blunt also because of the thin edge it can be sharpened very quickly..
sure the vic and wenger tools aint great steel , but they are not meant for whittling hardwoods or carving bone ,, theyer pocket knifes for lite use.. knife blade steel is fine in their multitools also.... it stays sharp long enough, if it i were to hard then theyed proably have a few broken blades and would cost the $ in warrenty $ due to the thinness of the blade and its shape.. also it would add costs to the amount of stones they buy per year.. and theyed add that to the price of the knives,... the vic butchers knives are soft as hell, but look most butchers dont even sharpen the knives properly only thin them out on a corse stone and steel them, if they were hard the butchers would have trouble...
id like it if victorinox and wenger made some pocket knives with better harder steel.. remember good only british pen knives many are 59-61 rockwell.. (same with surgical knives.. ) you can see this by the chips in their blades...
you can ben a vic blade and it wont spring back.. same with their kitchen and butcher knives... for me this is no problem... as they arnt ment to be hard and making them soft sames money on grinding stones and so keeps the price lower.. (wenger and victorinox are very well prices for their knives compared to knives from other makers that have insane quality problems... like many pen knives from europe and u.s. that cost more.. and are softer and poorer steel and most have many defects in the one knife.. for bad machine work )i would like to know how hard the toold head is as a good plier head should be in the high 50 rockwells.. like 57 -59.. it cshould be hard enought to chip and not fold,
2 things id like address on the vic multitoo are
1 , sand blast the screwdriver tips so the stick in the screws and not slip, who the hell polishes a screwdriver tip?? makes no common sence..
maybe ever titanium oxide coat the tips ,.. to help it stick to the scrwew heads.. although sand blasting would be enouth..2 make it so it is easy to remove broken tools or to remove tools one dosnt need and replace them with tools you want.....
.
-
@ausjulius said:
i dont know id be happy with tools at the hardness they ar eit is soft, but the blade is thin andyou can push it through things if it is blunt also because of the thin edge it can be sharpened very quickly..sure the vic and wenger tools aint great steel.
Hi
I find the Vic steel one of the best in the world.
NM
-
@ausjulius said:
i dont know id be happy with tools at the hardness they ar eit is soft, but the blade is thin andyou can push it through things if it is blunt also because of the thin edge it can be sharpened very quickly..sure the vic and wenger tools aint great steel , but they are not meant for whittling hardwoods or carving bone ,, theyer pocket knifes for lite use.. knife blade steel is fine in their multitools also.... it stays sharp long enough, if it i were to hard then theyed proably have a few broken blades and would cost the $ in warrenty $ due to the thinness of the blade and its shape.. also it would add costs to the amount of stones they buy per year.. and theyed add that to the price of the knives,... the vic butchers knives are soft as hell, but look most butchers dont even sharpen the knives properly only thin them out on a corse stone and steel them, if they were hard the butchers would have trouble...
id like it if victorinox and wenger made some pocket knives with better harder steel.. remember good only british pen knives many are 59-61 rockwell.. (same with surgical knives.. ) you can see this by the chips in their blades...
you can ben a vic blade and it wont spring back.. same with their kitchen and butcher knives... for me this is no problem... as they arnt ment to be hard and making them soft sames money on grinding stones and so keeps the price lower.. (wenger and victorinox are very well prices for their knives compared to knives from other makers that have insane quality problems... like many pen knives from europe and u.s. that cost more.. and are softer and poorer steel and most have many defects in the one knife.. for bad machine work )i would like to know how hard the toold head is as a good plier head should be in the high 50 rockwells.. like 57 -59.. it cshould be hard enought to chip and not fold,
2 things id like address on the vic multitoo are
1 , sand blast the screwdriver tips so the stick in the screws and not slip, who the hell polishes a screwdriver tip?? makes no common sence..
maybe ever titanium oxide coat the tips ,.. to help it stick to the scrwew heads.. although sand blasting would be enouth..2 make it so it is easy to remove broken tools or to remove tools one dosnt need and replace them with tools you want.....
.
I used my swisstool knife very hard and not sharpen it yet,its still very sharp,so I don't know what you mean about soft steel in Vic Wenger.They can't be wrong over 100 years,believe me.

-
Nothin' wrong with a Swisstool

-
i dont know id be happy with tools at the hardness they ar eit is soft, but the blade is thin andyou can push it through things if it is blunt also because of the thin edge it can be sharpened very quickly..
sure the vic and wenger tools aint great steel , but they are not meant for whittling hardwoods or carving bone ,, theyer pocket knifes for lite use.. knife blade steel is fine in their multitools also.... it stays sharp long enough, if it i were to hard then theyed proably have a few broken blades and would cost the $ in warrenty $ due to the thinness of the blade and its shape.. also it would add costs to the amount of stones they buy per year.. and theyed add that to the price of the knives,... the vic butchers knives are soft as hell, but look most butchers dont even sharpen the knives properly only thin them out on a corse stone and steel them, if they were hard the butchers would have trouble...
id like it if victorinox and wenger made some pocket knives with better harder steel.. remember good only british pen knives many are 59-61 rockwell.. (same with surgical knives.. ) you can see this by the chips in their blades...
you can ben a vic blade and it wont spring back.. same with their kitchen and butcher knives... for me this is no problem... as they arnt ment to be hard and making them soft sames money on grinding stones and so keeps the price lower.. (wenger and victorinox are very well prices for their knives compared to knives from other makers that have insane quality problems... like many pen knives from europe and u.s. that cost more.. and are softer and poorer steel and most have many defects in the one knife.. for bad machine work )i would like to know how hard the toold head is as a good plier head should be in the high 50 rockwells.. like 57 -59.. it cshould be hard enought to chip and not fold,
2 things id like address on the vic multitoo are
1 , sand blast the screwdriver tips so the stick in the screws and not slip, who the hell polishes a screwdriver tip?? makes no common sence..
maybe ever titanium oxide coat the tips ,.. to help it stick to the scrwew heads.. although sand blasting would be enouth..2 make it so it is easy to remove broken tools or to remove tools one dosnt need and replace them with tools you want.....
.
I used my swisstool knife very hard and not sharpen it yet,its still very sharp,so I don't know what you mean about soft steel in Vic Wenger.They can't be wrong over 100 years,believe me.

I think even the most loyal Victorinox users would concede that the blade steel used is "soft" compared to some of the steels used in other multitools and knives, and many like that because it makes it so easy to sharpen. It's not necessarily a criticism, just an observation.
@Magic Bus said:
Nothin' wrong with a Swisstool
Quite ;)
-
Pure curiosity, but I would love to see some accurate numbers relating to relative hardness between Vic and Leatherman

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login