Holy crap what a day....
-
-
The Curse of Lac LaPeche strikes again.

Once again Megan and I decided to go and paddle around Lac LaPeche. It was a pleasant paddle in the past, and, despite the above issues, we felt it was worth another shot. Little did we know that the Curse of Lac LaPeche wasn't done with us.

It started out as a nice enough paddle. We did a good chunk of the northern part of the lake. It was overcast, but expected to clear, and it was also pretty hot (either high 20's or low 30's) so no complaints even if it did rain a little. We visited Megan's old camp site, and scouted some other spots on the shore that looked interesting, and generally had a pretty good time.

As usual I was amused at how color coordinated Megan and I are in the Point 65 boat she usually paddles and the new Sun Flight kayak I recently picked up- of course, they paddle entirely different, but they look neat together.

This was where Megan and Sarah camped last year- the beaver lodge may have gotten bigger, or it may just appear that way since the water seemed a lot lower this year. Either way, I didn't get any photos last year because I was too busy dealing with.... well.... everything else! :ahhh

Other than being a bit overcast, the weather was great- not even a slight breeze, so the water barely had a ripple on it. It was so serene that it was almost boring....

We landed on a few nice beaches here and there to see if there were wild blueberries or other tasty edibles, but alas, no such luck. After several hours of paddling and exploring the large lake, we headed back, loaded up the trailer and headed for home, having seemingly escaped The Curse.
Nope.
Shortly before reaching home the trailer started to sway a bit, and at first I attributed it to wind or potholes. We were, after all, still in Quebec, a province famous for not maintaining roads or infrastructure. It got pretty bad at one point, but we were only a few blocks from home, so I kind of babied it until we got to our driveway, and I went to back the trailer into our spot. That's when I noticed the passenger side wheel wobbling. Badly.


I had destroyed a wheel bearing so badly that it kicked off the grease cap and vomited grease all over the wheel.
I was sure that I'd serviced these bearings at the beginning of the season, but it appears from the mess that I forgot, and apparently only did the bearings on the Apache, and not on my utility trailer. I pulled off the hub and there were just fragments of the bearings left in the grease.
I cut my fingers pretty good on jagged metal as I tried to haul out what was left of them to clean the hub and install new bearings, and I even had to cut the old bearing housing off the spindle as it had gotten so hot it pretty much fused on. Thank the Maker for my Dremel tool! We then headed off to Canadian Tire for replacement bearings and some fresh grease.

After we got back, the next problem was trying to remove the race from the hub, and Megan and I took turns pounding on it for a couple of hours before we admitted defeat. The heat that was generated that fused the housing to the spindle also apparently fused the race to the hub, which meant new hubs were needed, so we went to Princess Auto for those. It's a bit further away, but they are more likely than Canadian Tire to have the hubs I need.

Naturally they didn't have a direct replacement for my big, heavy cast iron ones, so I had to try and locate a suitable replacement set. Since I know nothing at all about how to size these things, I grabbed an employee and asked him. Soon we had three employees around us, all arguing over what we needed, and, as it turned out, all of them were barking up the wrong tree.

As the store was closing for the night (it was now almost 9 pm) we left without buying anything, and, as I drove home, Megan started searching the Internets for the answer.
By the next morning, she believed she knew what we needed, and she insisted that we go to the other Princess Auto in town so as not to be confused by the people that should have known. We got there, spoke to another employee, who confirmed what Megan believed was the correct set of parts and we left.
It's important to point out that I can build just about anything, as long as I have the right parts, so I would have been lost without Megan's insights into the correct parts. As it turned out, the bearings that came with the kit had the correct size external ring, but were sized for a larger spindle, and so had an incorrect internal ring size- luckily I had purchased the correct bearings at Canadian Tire the day before, so the good news was that I finally had all the right parts. The bad news is that the bearing kits from Canadian Tire cost a pretty penny, and the hubs weren't exactly cheap either, so I had been hoping to be able to return the original bearing kits and get some of my money back. That wasn't in the cards though, and this whole repair cost me well over $200.


But, with all of the correct parts, it didn't take long to grease up the bearings, races, seals and collars and install them. The new hubs are sharp looking and also weigh a fraction of what the old ones did, so no complaints from me. I did one side while Megan took care of the undamaged side (I wasn't going to just replace one side!) and we soon had it back up and running- or so we'd hoped, because we actually were supposed to spend a couple of days at a friend's cottage, almost two hours away, and we needed the trailer for that!

We stopped every twenty minutes or so to check to see if the bearings were heating up, leaking grease or had any other telltale signs, but it performed like a champ, just as I have come to expect from my trusty utility trailer!
The Curse of LaPeche got us again and cost me some money and time, but at least I got to deal with it in the comfort of my own driveway this time, and at least we got to enjoy a nice paddle first!
Def
-
Nice pics and a good ending

-
You did all this with just a Spartan and some gun powder, right?
-
Glad it worked out Boss. Nice pics btw.
-
For you, that sounds like a very successful day mate :D
Is there anything left of the old trailer, or have you replaced it all now :P
All joking aside, glad you got it sorted a lot quicker than in some of your previous escapades

-
You know, a can or two of spray paint wouldn't cost very much. We use the black, high temperature, BBQ grill paint for touching up scratched Jeep bumpers after trail rides, and it would also work a treat on your trailer.

-
@Mechanickal said:
You did all this with just a Spartan and some gun powder, right?I'd have traded a Spartan for some useful help at the store, does that count? :-P
Def
-
@50ft-trad said:
For you, that sounds like a very successful day mate :DIs there anything left of the old trailer, or have you replaced it all now :P
All joking aside, glad you got it sorted a lot quicker than in some of your previous escapades

Well....
The deck and body are still original, although I need to replace the deck at some point as the wood is pretty rotten. Also the axle, hangers and springs are original, although I will admit to having given serious consideration to replacing all of that. A 1500lb axle (that included hubs) was on sale at Princess Auto for $125 and it seemed like a no brainer to get that instead of the two individual hubs at $65 each. The problem with that was that I currently have a 2000lb axle with 5 bolt hubs and 5 bolt wheels while the axle on sale was only 4 bolt, which meant that I would have had to either buy hubs on top of the axle, or buy three new wheels and tires too.
This is the most expensive $500 trailer I own.... although the Apache is a close second!
Def
-
@Alan K. said:
You know, a can or two of spray paint wouldn't cost very much. We use the black, high temperature, BBQ grill paint for touching up scratched Jeep bumpers after trail rides, and it would also work a treat on your trailer.
When I replace the deck (probably next year) I'm going to strip all the old paint off it and give it a good coat of bedliner.
And then probably another good coat of bedliner, just because.....
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login