powerlock owners club,
-
It's the NSN (nato stock number ) mate, it's what military kit gets stamped with.
-
Following RF52's recently concluded challenge I am currently thinking about adding a PowerLock to my array of multitools - 'collection' is too big a word for it.
This should be viewed against the background that I only have one SOG, namely the Power Access Deluxe. The Powerlock calls to me because of its predisposition to factory sanctioned modding.
So, a few questions to you guys:
Should I go for a brand new one (China) or try to secure a rarer older one (preferably still US made) - how rare are these anyway?
Set against the PAD, will I be disappointed with the PL's build quality? Does the answer depend on the choice between newer and older, and if yes how much? And compared to, say, a LM Wave?
Is the file any better than the PAD's? (I sure hope it is, can't be any worse at any rate :D)Thanks in advance

-
Just to add I have finished reading Nix' challenge thread. I must admit that I somehow missed it while it was taking place, my only excuse being that I had two consecutive challenges going on at the time, not to mention summer vacation (such stress! ;)).
I also have to thank Nix for multiple references to my habits

While I am a little bit wiser now, I may still pull the trigger, if only to prove that SOG can build better tools than the PAD (even if not ideal viewed by LM or Vic standards). I have noted as main weaknesses the scissors and the file, plus the blade edge's tendency to dull by rolling easily.
To mitigate I'd probably prefer the V-cutter over the scissors, and fit a full PE blade instead of the part SE part PE one. The file, well, I could do the Wave file trick on that, I suppose. But let's see about that, the rounded SOG file might be so much better than the squared-end one as to be actually usable.
Does anyone have any insights to share before I pull the trigger?
-
I don't really have anything to share which you haven't already seen in my challenge, but personally I like the Powerlock [emoji106] The only thing I wasn't perfectly happy with is: the knife rolls from hitting the inside of the handle but can be avoided if you don't slam it in there. And the "hard" wire cutters feels a bit on the soft side, but for cutting electrical wire and softer solid wire it worls like a charm [emoji106] Hope this helps

Mine is the new one, the older one might be even better [emoji106]Sent fra min FRD-L09 via Tapatalk
-
RF52! -
PowerLock S60 and old coins

S60 model with scissors. Leather sheath (but I swap out with a nylon from PowerAssist). I have had good luck with this tool. SOG in general. The one-handed flip opening worked first time and every time. In fact, I slightly tightened the screws to prevent knuckle-rap. Works a charm!
The 4" holder opens at right angle, *AND *the cover closes. I have seen a few models, maybe older ones, with covers too long to use the very hand right angle position.
-
@israelpiper said:
PowerLock S60 and old coins

S60 model with scissors. Leather sheath (but I swap out with a nylon from PowerAssist). I have had good luck with this tool. SOG in general. The one-handed flip opening worked first time and every time. In fact, I slightly tightened the screws to prevent knuckle-rap. Works a charm!
The 4" holder opens at right angle, *AND *the cover closes. I have seen a few models, maybe older ones, with covers too long to use the very hand right angle position.
Very nice photo! And thank you for sharing your experience.

-
PowerLock S60 and old coins

S60 model with scissors. Leather sheath (but I swap out with a nylon from PowerAssist). I have had good luck with this tool. SOG in general. The one-handed flip opening worked first time and every time. In fact, I slightly tightened the screws to prevent knuckle-rap. Works a charm!
The 4" holder opens at right angle, *AND *the cover closes. I have seen a few models, maybe older ones, with covers too long to use the very hand right angle position.
Very nice photo! And thank you for sharing your experience.


though be careful putting PowerLocks and coins together,

SOG used to advertise their Compound Leverage Patent by cutting coins in half with their PowerLocks at the knife shows :D -
@israelpiper said:
PowerLock S60 and old coins

Nice pic!

-
Please find attached my membership application form.
-
Nice DT

Sent fra min FRD-L09 via Tapatalk
-
Not much action here for a while.
My Powerlock was a big help in putting the bed in the new guestroom together.
Great idea to put a 1/4" bit driver on the PL

Sent fra min FRD-L09 via Tapatalk
-
Not much action here for a while.
My Powerlock was a big help in putting the bed in the new guestroom together.
Great idea to put a 1/4" bit driver on the PL

Sent fra min FRD-L09 via Tapatalk
Good work! The PL is a good choice for that sort of job.

Thanks gerleatherberman

It works very well, and the handle feels good in hand when turning the screws
Sent fra min FRD-L09 via Tapatalk
-

May have to pair a PL with the challenge tool tomorrow. :) -
SOG PowerLock: Added thumb rest for close work

A small thing, but for me adding the opener to the open blade helps with diminishing thumb pad irritation. Since the serrations are, by my reckoning, backward, I don't have a straight blade edge down by the close end. No push-cuts. The added thumb rest just feels better when using the straight edge upper half. Better force and balance. I like smaller combination blades on multitools, but as Victorinox does it for many pocket knives (in the right place, and YES easy to sharpen). Straight blade close-in, for push-cuts. The SOG PowerLock isn't my go-to MT for bushcraft by any means, partly because of the blade. But I stumbled on the use of the open blade and opener together, as a work-around slight improvement. I use double or triple tool openings on my SwissTool Spirit for the large driver/pry bar, and on the SwissTool I back the chisel with the large driver/pry bar; the large driver and awl on the LM Surge for starting a number of screw and controlling depth. Small useage techniques which add up to greater utility, for me at least.
-
Great tips, israelpiper!

-
My first SOG arrived today




Thanks Fuzzy
The snail mail was snaily, but it made it :D -
You're very welcome.

-
WARNING-NECROTHREAD REVIVAL!!!
I know it's been 7 months since some kind of action had been seen here but, I had to have at least one representative of the SOG group; from what I'd seen, it was the PowerLock that got my attention and, finding one B61 "discounted" helped my decision making. Love the burnished stainless steel, the smoothness of the pliers mechanism, the ability to open/close the pliers Balisong-style and, that compound leverage is pretty awesome. The nylon sheath that came with the tool can fit the bit kit along with the PowerLock (although I made a "divider" so that the bits don't come out or get on the way as I return the tool) and it's not too obstrusive. The tool's driver are good, as are the openers (and liking a lot the awl!). On the other end of the spectrum, the scissors struggle cutting even string/threads, particularly if using just the tip; the combo knife, although razor sharp, if flexes considerably. Wood saw blade is good, but I find quite short (reminds me of the cutting area of the Surge' curting area). The bit driver is nice but, it's difficult to use at 90 degrees as the cover does not have a cutout for it to pass thru, havinh either to remove the cover or keep the tool fully open! The file, although not even on par to Gerber's MP standards, the double cut side is good (the single side is pretty good on my fingernails; take that, PAD!) But the "cutting/deburring edge" is non functional in mine; it feels more like a rough edge than a cutting surface. My only grieve is that, unlike Vic's Swisstools or most Leathermans (Leathermen!?!?), I can't open the handles "180degrees" to use the tool as a long, center driven screwdriver. But, I think its a pretty good tool in all and I'm beginning to appreciate it. So, here it is!!!! [attach id=0 msg=2329101] [attach id=1 msg=2329101]


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login