kamakiri's Former Lurker / New Member Intro (long read)
-
This is definitely not boring kamakiri keep up the good work

-
Most welcome!

-
Very entertaining

-
<u>Project: 'Troublemaker'</u>
Had some time to finish my Troubleshooter Lite + Pen. Waffled a bit about adding a Wood Saw and using the Corkscrew instead for this temporary/test build and making it a Handyman Lite Plus, but it would add time to get the Saw from the fodder box. And adding another Layer would make it close to Champ size. This way it would still be about a half layer thinner than a Champ and about a full layer thinner than a CT Lite but have at least 1 saw. Intent is to have a Magnifier in place of the In-line Phillips for the 'final' build.
Misc polishing:

Don't need this:

'free' pins during assembly:

Layer 1 Openers/Awl:

Layer2 Lite (would add magnifier here on permanent build instead of phillips):


Layer 3 Pliers (FYI - If I put the scissor here it could save a 1mm spacer):

Layer 4 Scissor/Hook:

Layer 5 Saw/Chisel:

Layer 6 Blades and back Phillips:

Top view:

Measure and trim pins:

Hammer Time:





Pressed on original/modified for pen scales:




@CallsignBadger said:
Very entertaining

Thanks, CsB...I hope this one was, even if a little. Was glad for the knife time today and to finish this one. 
-

Nice one

-
Thanks again CsB!
Troublemaker living up to its name...showing off new hardware to it's sibling and Hoffritz cousin:

-
Nice peening, excellent work Kamakiri 
-
Excellent work kamakiri

-
Nice limited edition

-
@MTMatt said:
Nice peening, excellent work Kamakiri 
Thanks, MTMatt! Better looking than when I clip-n-hammer for temporary builds using the damaged bushings!Thanks, Wspeed! I always put more effort with builds that may be permanent. And get even pickier with restorations. I left one of the pins about 0.12 mm longer than I wanted and would have taken it off for a restoration, but okay for a user like this.
Thanks, CsB! I hope there's still entertainment value in there!

I thought you might notice that, Ray!
;)
Gotta quickly figure out what I'm going to do with knife time this afternoon...might just be cleaning some of the recent arrivals.

-
@MTMatt said:
Nice peening, excellent work Kamakiri 
Thanks, MTMatt! Better looking than when I clip-n-hammer for temporary builds using the damaged bushings!Thanks, Wspeed! I always put more effort with builds that may be permanent. And get even pickier with restorations. I left one of the pins about 0.12 mm longer than I wanted and would have taken it off for a restoration, but okay for a user like this.
Thanks, CsB! I hope there's still entertainment value in there!

I thought you might notice that, Ray!
;)
Gotta quickly figure out what I'm going to do with knife time this afternoon...might just be cleaning some of the recent arrivals.

Oh yeah, I saw!

Glad you got it!

-
I said I buy crap...sometimes it's not intentional.
Small blade in the listing only mentioned 'light scratches' and said nothing about the very pronounced BENT TIP ::)
Mother Hamster Smurf it ALL:

a bit better:

Still too visible from the blade side:

Good enough to leave for now. At least it sits nowhere near the main blade now.

Rest of the knife and the edge on this blade was great so I didn't want to bother with a return or refund or pulling it apart to replace the blade. I have enough of those to do that I knew about when purchasing. ::)
Just glad I didn't have any errant blows and ruin the factory edge. Still cuts nicely and separates news print just fine.
-
Luckily it’s not too badly bent kamakiri

-
Yeah, not too bad and I've fixed worse but with some degradation of the cosmetics. I'm more concerned with not marring the edge or sides on this one. Making it straight might come at the expense of some surface dimpling. I always try for the 'right' fix for the given condition.
-
Excellent job on the blade straightening

-
@kamakiri said:
Yeah, not too bad and I've fixed worse but with some degradation of the cosmetics. I'm more concerned with not marring the edge or sides on this one. Making it straight might come at the expense of some surface dimpling. I always try for the 'right' fix for the given condition.Or... you've got to know when to stop :D
Excellent fix Kamakari
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
