February Fixie Challenge
-
Nice pic!

-
Just a photo today, i was doing cutting tasks later in the day but had to resort to my backup Pioneer as i ended up in a public place, Pioneer at least didn't raise any eyebrows

Day 5

-
Great pics everyone

-
Used the Mora to peel an orange for lunch at work today.

-
day 5: have I ever mentioned I've got a sweetooth too?
-
@Nix said:
This one is for Styx:
Helle Lappland, Koyote LeukuI noticed that current Lappland knives are made of Sandivik steel. This one is a laminated steel. Not sure when the made the change.
Nice! Really
the Lappland! Been looking at one myself, but haven't taken the leap yet 
Sent fra min FRD-L09 via Tapatalk
-
Great pics and uses guys!

Really enjoying this challenge and seeing what you use the different knives for
Day 7:
Cutting some more labels for the fire suppression systems I'm doing the yearly check's on.
Abbused the knife and sharpened it with a few quick strokes on a piece of wood with a glued on strip of 400 grit sandpaper.
Opened a letter telling me my birthday gift for myself are in the country. Thanks for the help Nix

And opened some birthday gifts







Sent fra min FRD-L09 via Tapatalk
-
Nice uses and pics, guys!

-
Day 5:
Swapping to this little one from kukri house.
-
@FInixNOver said:
Day #5 - no uses today
I'm on a business trip so, just took the little guy out for a photo, during my afternoon run, after checking in at the hotel.

Sent from my Redmi Note 5
Nice photo!

-
Only use was an apple today...glamour shot with my EDC pencil

-
Like the new blade, Sak60!
-
Day 05:
An interesting day....
I'm making pizza for dinner this evening. The dough got made yesterday and has been doing it's thing al day now. Mrs Nix want a garlicky sauce for the pizza, and so the Ulu had a chance to jump into the action.

The flat of the Ulu's blade is great for smashing the garlic. The sharp edge used with a little rocking motion made a rough chop fairly simple. I will say that when working on small thing, like a garlic clove, my hand gets in the way of seeing what's going on. It may seem odd to use an 8" Chef's knife to chop garlic, but that's what I usually use. Lot's of space, lots of control.
So, even though the Ulu did a fine job with the garlic smash & chop, I still feel I have more control with a bigger knife. And better visibility.
I needed some tomato puree for the sauce and I decided to see if the Ulu could be used as a can opener. I figured the sharp corners could be used to puncture than can and then cut the lid off in small bites. This proved to be a bit harder the expected. I've used several fixies to open a can, so I do have a reference point for this task. This Ulu got the can open, but it wasn't pretty.

After cutting the can open I checked the edge......
Chipping!

Zoomed in here:

You can see that the corner is chewed up a good bit. Bummer.
This blade is made with D2 steel. D2 has a reputation for chipping, so to a certain degree this isn't a huge surprise. However, in this case, I think it is more due to the blade shape and edge geometry. I'm also guessing now that this is not CPM-D2, which has a finer grain and carbide structure.
I brought out the water stones and went to work trying to grind out the chips. This is a tricky knife to sharpen! The edge and bevel are continuously changing and, more significantly, the handle limits how one can address the stones. I felt really awkward trying to sharpen this knife. I've touched it up in the past on a ceramic rod, without a problem, but trying to grind out a chip was a hassle.
Nevertheless, I did get the chipped area to be smoothed out (there is still a slight chip in the edge, but it is much better) and the greater portion of the blade is now shaving sharp. It slips right through fine paper. This steel may chip easily, but it sure takes a good edge.
Lesson learned, be careful with this blade!
-
Sorry to hear about the chipping but glad it is back to shaving sharp!
Great post and photo’s!
How did the pizza turn out? Tasty???
-
Day 05, bonus shots:

You can see by the light's reflection that the surface of the bevel is somewhat uneven now. The bevel is actually smoother than the machined factory edge, but it does look irregular. This is because I had difficulty maintaining a constant angle over the continuously arcing blade.
Not a big deal. As I said the Ulu is super-sharp now. But is does look a little funny.
I have an Idea how I might even that out, but I'm not sure I want to mess up the edge just for some aesthetics. Maybe after it gets some more use I'll see about evening the appearance. Just for fun, if nothing else.
Pizza: Yes!
The pizza was great! (Even Mrs Nix, who has high standards for pizza, if not for husbands, gave her approval.
)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

