Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Gathering thoughts/tools/materials for first mod

Scheduled Pinned Locked Moved The Mod Squad
37 Posts 1 Posters 2.2k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. Gathering thoughts/tools/materials for first mod
Gathering thoughts/tools/materials for first mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • comis Offline
    comis
    Posts: 11,394
    comis Offline
    comis
    wrote on last edited by
    #8 Quote Reply

      @Vidar said:
      +1 to drill press for drilling in metal. You'll save yourself drill bits, frustrations, time and blood pressure - it is almost a bargain! (And some stuff is just next to impossible without one).

      A little comment on making precise sized holes - normal drill bits tend to make holes a little bit off size wise, and often make slightly triangular holes in thin stock. Putting some sacrificial wood on both sides of thin metal tend to help.

      For precisely sized holes get a slightly undersize drill bit and a matching reamer for the size you want. Reamers in the sizes we talk about with SAKs are fairly inexpensive.

      Looks like getting a drill press to make precision holes is now a must have, and the reamer indeed is a great idea too!(Didn't think about that at all :facepalm: )
      Thank you! :tu:

      1 Reply Last reply
      • comis Offline
        comis
        Posts: 11,394
        comis Offline
        comis
        wrote on last edited by
        #9 Quote Reply

          @Dutch_Tooler said:
          You're welcome, glad to be of help :cheers:

          :cheers: :cheers: Now just gonna start looking up good solid drill press...

          1 Reply Last reply
          • Vidar Offline
            Vidar
            Posts: 2,605
            Vidar Offline
            Vidar
            wrote on last edited by
            #10 Quote Reply

              @comis said:
              :cheers: :cheers: Now just gonna start looking up good solid drill press...

              For the sizes discussed here you might also want to consider (used) small lathes. Most have some way of sticking your very non-round piece to either the chuck or some milling attachment - either way will also work as a drill press. A small lathe will likely have less run out than any inexpensive drill press. (If you have a choice a collet setup will be more precise than a Jacobs chuck).

              Than again, there is precision and there is precision - for practical purposes it will likely be next to no difference between a perfect and a slightly off one. Just as a reference for perfect a free running sliding H7/F7 hole/shaft tolerance for 3mm is 0 to +0.01mm for the hole, and -0.006 to -0.016mm for the shaft.

              ~~If you have little space, lots of patience, and feel a bit more exotic then you might want to go more look up DIY EDM (electro discharge machining). They will make a silly precise hole in anything conductive. Hardened or not makes no difference at all. ~~(Please don't electrocute yourself or burn down the house).

              1 Reply Last reply
              • comis Offline
                comis
                Posts: 11,394
                comis Offline
                comis
                wrote on last edited by
                #11 Quote Reply

                  @Vidar said:
                  For the sizes discussed here you might also want to consider (used) small lathes. Most have some way of sticking your very non-round piece to either the chuck or some milling attachment - either way will also work as a drill press. A small lathe will likely have less run out than any inexpensive drill press. (If you have a choice a collet setup will be more precise than a Jacobs chuck).

                  Than again, there is precision and there is precision - for practical purposes it will likely be next to no difference between a perfect and a slightly off one. Just as a reference for perfect a free running sliding H7/F7 hole/shaft tolerance for 3mm is 0 to +0.01mm for the hole, and -0.006 to -0.016mm for the shaft.

                  ~~If you have little space, lots of patience, and feel a bit more exotic then you might want to go more look up DIY EDM (electro discharge machining). They will make a silly precise hole in anything conductive. Hardened or not makes no difference at all. ~~(Please don't electrocute yourself or burn down the house).

                  I am totally newbie when it comes to machine shop, and definitely thank you for sharing your tips with me! :cheers:

                  In my research on tools, I have been focusing on hand power drill and drill press, and only seen some YT footage on mini lathe...but it does give me the feeling that it might be a hit and miss thing in finding a good mini-lathe.

                  To a layman like myself, I have a feeling it might be more difficult to get good at using the lathe than a simple drill press. However, I did read that people could bore threads out of brass rod for pivots...which sounds like a dream. Given my very limited knowledge and space, just don't know whether it might be an overkill to get one. Really gonna research hard on this one, even before thinking to get one.

                  It sounded like the 'collet' setup will hold the bit better than a 'jacob chuck' setup, is this also true for drill press?

                  Final paragraph just totally went over my head...I know what S Club 7 is, but I ain't gonna even pretend I know what H7/F7 is... :facepalm: :P

                  download (1).jpg

                  1 Reply Last reply
                  • Vidar Offline
                    Vidar
                    Posts: 2,605
                    Vidar Offline
                    Vidar
                    wrote on last edited by
                    #12 Quote Reply

                      @comis said:
                      In my research on tools, I have been focusing on hand power drill and drill press, and only seen some YT footage on mini lathe...but it does give me the feeling that it might be a hit and miss thing in finding a good mini-lathe.

                      My impression is that the inexpensive ones from China is a bit hit and miss. That said most say usable if it works - apparently it helps to mount it on something stiff and sturdy. Personally I would look for a decent used US or European brand one - one the reasons being that the heap and accessories and tools that often come with a used one easily cost as much as the lathe itself. I

                      I see you are in Hong Kong (?) so I get the tight space thing - the IKEA in Hong Kong was the most compact one I've ever visited!:D If you have a tight space you might want to look into used watchmakers lathes - they are made for small stuff, and are quite delicate themselves. Be aware though that some of those don't have much power at all, and some even lack a normal toolholder.

                      Used lathes are a bit hit and miss too, but a hit can be a real hit - many sellers are third-parties which have no idea what they are selling. A nice reference for machine tools is [email]lathes.co.uk[/email] .

                      The problem with a cheap drill press is that they will surely be decent at the press thing, but it might run a relatively big runout. For many tasks where these are used that doesn't matter much (wood), but for precise holes in metal that might be an issue. In particular if running carbide tools which really don't like shocks. A metal lathe on the other hand is made for a low runout and to handle metal level precision. And if you need other round parts anyway... (And while a lathe can be pushed into servise as a drill press, the other way around is usually not true).

                      @comis said:
                      To a layman like myself, I have a feeling it might be more difficult to get good at using the lathe than a simple drill press. However, I did read that people could bore threads out of brass rod for pivots...which sounds like a dream. Given my very limited knowledge and space, just don't know whether it might be an overkill to get one. Really gonna research hard on this one, even before thinking to get one.

                      To make tiny threads, even with a lathe, the easiest solution is die and taps. Having a lathe helps to align and move things straight, but it is fairly easy to make a little jig and do it manually too. Just making a tight straight hole in something to fit either the material or tap will help a lot. That said threaded pivot will be weaker than a similar sized riveted one.

                      Getting a lathe to make a few holes for a SAK is clearly overkill. Then again you might end up making more stuff or get a new hobby :)

                      @comis said:
                      It sounded like the 'collet' setup will hold the bit better than a 'jacob chuck' setup, is this also true for drill press?

                      Yes. Most drill presses only use Jacobs chucks though. Again, it says something about the precision it is intended for. Mind you, I do think that precision will still do fine for a SAK. If in doubt do undersize and get a reamer :) Precision is a very deep and expensive rabbit hole, and it is important to know good enough. But if some collets happen to come with a used machine then great. Good collets tend to be expensive.

                      @comis said:
                      Final paragraph just totally went over my head...I know what S Club 7 is, but I ain't gonna even pretend I know what H7/F7 is... :facepalm: :P

                      H7/F7, and other various combinations like it, are tolerance standards for fitting parts together. Nothing is truly made to ideal measures so they help provide working tolerances. Importantly they also help to establish good solutions for various kinds of fits and uses. For instance some will want a hole to lock onto a shaft and not move or rotate afterwards. Some might want to be able to rotate and slide it tightly (like the H7/F7). Others might need to be able to easily disassemble and reassemble often. And so on. Anyway, it was just meant as an example of tolerances for a nice tight fit. (Thus practically speaking a gap between hole and shaft of some 0.005 to 0.02 mm will be tight but still rotate.

                      1 Reply Last reply
                      • comis Offline
                        comis
                        Posts: 11,394
                        comis Offline
                        comis
                        wrote on last edited by
                        #13 Quote Reply

                          @Vidar said:
                          My impression is that the inexpensive ones from China is a bit hit and miss. That said most say usable if it works - apparently it helps to mount it on something stiff and sturdy. Personally I would look for a decent used US or European brand one - one the reasons being that the heap and accessories and tools that often come with a used one easily cost as much as the lathe itself. I

                          I see you are in Hong Kong (?) so I get the tight space thing - the IKEA in Hong Kong was the most compact one I've ever visited!:D If you have a tight space you might want to look into used watchmakers lathes - they are made for small stuff, and are quite delicate themselves. Be aware though that some of those don't have much power at all, and some even lack a normal toolholder.

                          Used lathes are a bit hit and miss too, but a hit can be a real hit - many sellers are third-parties which have no idea what they are selling. A nice reference for machine tools is [email]lathes.co.uk[/email] .

                          The problem with a cheap drill press is that they will surely be decent at the press thing, but it might run a relatively big runout. For many tasks where these are used that doesn't matter much (wood), but for precise holes in metal that might be an issue. In particular if running carbide tools which really don't like shocks. A metal lathe on the other hand is made for a low runout and to handle metal level precision. And if you need other round parts anyway... (And while a lathe can be pushed into servise as a drill press, the other way around is usually not true).

                          To make tiny threads, even with a lathe, the easiest solution is die and taps. Having a lathe helps to align and move things straight, but it is fairly easy to make a little jig and do it manually too. Just making a tight straight hole in something to fit either the material or tap will help a lot. That said threaded pivot will be weaker than a similar sized riveted one.

                          Getting a lathe to make a few holes for a SAK is clearly overkill. Then again you might end up making more stuff or get a new hobby :)

                          Yes. Most drill presses only use Jacobs chucks though. Again, it says something about the precision it is intended for. Mind you, I do think that precision will still do fine for a SAK. If in doubt do undersize and get a reamer :) Precision is a very deep and expensive rabbit hole, and it is important to know good enough. But if some collets happen to come with a used machine then great. Good collets tend to be expensive.

                          H7/F7, and other various combinations like it, are tolerance standards for fitting parts together. Nothing is truly made to ideal measures so they help provide working tolerances. Importantly they also help to establish good solutions for various kinds of fits and uses. For instance some will want a hole to lock onto a shaft and not move or rotate afterwards. Some might want to be able to rotate and slide it tightly (like the H7/F7). Others might need to be able to easily disassemble and reassemble often. And so on. Anyway, it was just meant as an example of tolerances for a nice tight fit. (Thus practically speaking a gap between hole and shaft of some 0.005 to 0.02 mm will be tight but still rotate.

                          Thanks again! :tu:

                          I think that's one thing I do envy of my friends in US and Europe, that many machine tools could be brought/shipped/traded at a relatively reasonable cost. And as you have mentioned, living/working space in HK is genuinely really tight, and being a metropolis, people have less leisure time to enjoy their hobbies and space to do it. It really is not easy to pick up any DIY hobbies.

                          Watchmaker Lathe? Not that I am making anything big and needs powerful machine, but I figure even for a hobbyist/weekend warrior maybe it need to be a certain size to make it worth the money/space. :think:

                          The link you gave is massive, I think it will be really intriguing for someone whom are serious about the craft.

                          I totally agree with the cheap drill press comment...but like Lathe, it is probably a hit/miss thing with Chinese brands. So far, I only see a Chinese brand called "West Lake" which has distributor locally and have good feedbacks from local DIYers. Here are some info about it:

                          Link Preview Image
                          You searched for WEST LAKE - 三寶五金機械有限公司

                          favicon

                          三寶五金機械有限公司 (triple.com.hk)

                          I am thinking about the ZHX-13 13mm drill press or the bigger brother 16mm ZQ-4116 ZQ4116... :pok: :think:

                          1 Reply Last reply
                          • Vidar Offline
                            Vidar
                            Posts: 2,605
                            Vidar Offline
                            Vidar
                            wrote on last edited by
                            #14 Quote Reply

                              @comis said:
                              I think that's one thing I do envy of my friends in US and Europe, that many machine tools could be brought/shipped/traded at a relatively reasonable cost.

                              Well, you have nothing to envy me for sure. Nothing reasonable about shipping costs here.

                              @comis said:
                              Watchmaker Lathe? Not that I am making anything big and needs powerful machine, but I figure even for a hobbyist/weekend warrior maybe it need to be a certain size to make it worth the money/space. :think:

                              Some are quite decent and some excellent for small size work. And sometimes they show up for song and dance. Maybe because there are less watchmakers these days?

                              On another note you might want to take a look at the Sherline and Taig mini-lathes. They have many different configurations, and can be reconfigured as small mills too. And they take collets. (Go for ER collets if you want something alround). They are tiny and budget priced, but some people make incredible stuff with them. Worth googling around a bit - surely there must be some in HK as well.

                              @comis said:
                              The link you gave is massive, I think it will be really intriguing for someone whom are serious about the craft.

                              That link is very very useful if you consider used manual machinery.

                              @comis said:
                              I totally agree with the cheap drill press comment...but like Lathe, it is probably a hit/miss thing with Chinese brands. So far, I only see a Chinese brand called "West Lake" which has distributor locally and have good feedbacks from local DIYers. Here are some info about it:

                              Link Preview Image
                              You searched for WEST LAKE - 三寶五金機械有限公司

                              favicon

                              三寶五金機械有限公司 (triple.com.hk)

                              I guess you wont be able to actually test it first, so some ways to sort chiffs from chaffs might be the common price and user experiences. If it comes with a test certificate that is a very good sign but not common on inexpensive stuff. (Some cheap stuff do come with a test certificate - the problem is that all the machines have the same test results... :whistle: ). For a drill press a geared head is a good sign - metal gears better than plastic gears of course. (One sacrificial plastic gear might be ok). A collet option is a good sign, the same with a cooling system, and if it has the ability to do threading that is promising too.

                              The thing is though - pretty much any drill press makes wonder compared to freehand, and for SAK mods it should do fine.

                              1 Reply Last reply
                              • Dutch_Tooler Offline
                                Dutch_Tooler
                                Posts: 4,434
                                Dutch_Tooler Offline
                                Dutch_Tooler
                                wrote on last edited by
                                #15 Quote Reply

                                  I bow to your greater training and experience Vidar :salute:

                                  I hadn't thought about using the lathe as a drill press for instance :facepalm: and of course it could be used for that, given a good way of fixing the object to the sled... even with auto advance included for free :D

                                  That said, the more sophisticated, the better is of course true, but perhaps liquid cooling attachments (nozzles and recirc pumps) is pushing the needs beyond those needed for DIY in the SAK and multitool area. And at the precision we are talking about, a Jacobs chuck will do the job admirably and collets will not be strictly necessary IMHO. Depends a bit on how much more you plan to possibly do in future, I guess...
                                  Sourcing sufficiently precise basic machinery is a real concern, I can see that, especially in the smaller sizes for DIY and smaller workshops. My lathe is an Austrian Emco Compact 5 (alas without the hard to get milling attachment) which should suit DIY needs but is no.longer available new.

                                  1 Reply Last reply
                                  • comis Offline
                                    comis
                                    Posts: 11,394
                                    comis Offline
                                    comis
                                    wrote on last edited by
                                    #16 Quote Reply

                                      @Vidar said:
                                      Well, you have nothing to envy me for sure. Nothing reasonable about shipping costs here.

                                      :facepalm:

                                      @Vidar said:
                                      The thing is though - pretty much any drill press makes wonder compared to freehand, and for SAK mods it should do fine.

                                      That's a comforting thought...I think as a hobbyist and a total newbie, it might be prudent to grow my skill before acquiring heavy tools I have yet idea how to make good use of.
                                      And a big thank you for sharing all those info, this experience will be of great reference down the line. :salute:

                                      @Dutch_Tooler said:
                                      I bow to your greater training and experience Vidar :salute:
                                      I hadn't thought about using the lathe as a drill press for instance :facepalm: and of course it could be used for that, given a good way of fixing the object to the sled... even with auto advance included for free :D

                                      That said, the more sophisticated, the better is of course true, but perhaps liquid cooling attachments (nozzles and recirc pumps) is pushing the needs beyond those needed for DIY in the SAK and multitool area. And at the precision we are talking about, a Jacobs chuck will do the job admirably and collets will not be strictly necessary IMHO. Depends a bit on how much more you plan to possibly do in future, I guess...
                                      Sourcing sufficiently precise basic machinery is a real concern, I can see that, especially in the smaller sizes for DIY and smaller workshops. My lathe is an Austrian Emco Compact 5 (alas without the hard to get milling attachment) which should suit DIY needs but is no.longer available new.

                                      Vidat and Dutch_Tooler, come to think about it, since you guys have much more experience in lathe and all things machine, how difficult is it to make suitable M2 and M1.5 screw pivots for 93mm?

                                      1 Reply Last reply
                                      • Dutch_Tooler Offline
                                        Dutch_Tooler
                                        Posts: 4,434
                                        Dutch_Tooler Offline
                                        Dutch_Tooler
                                        wrote on last edited by
                                        #17 Quote Reply

                                          Easy, at least for the M2 I use. Drill 3mm or 2.5 mm brass stock to nominally 1.6 mm (1.5 will work too) in a lathe at one end (for accuracy use a centering drill first), cut off at desired length, reverse and put in chuck, drill other end, tap M2 (for brass and good screw retention just using the #1 tap will do; you can drive the chuck and hold the tap holder if you feel brave enough), reverse, tap M2 first end, ready. Sequence may vary slightly.

                                          1 Reply Last reply
                                          • comis Offline
                                            comis
                                            Posts: 11,394
                                            comis Offline
                                            comis
                                            wrote on last edited by
                                            #18 Quote Reply

                                              @Dutch_Tooler said:
                                              Easy, at least for the M2 I use. Drill 3mm or 2.5 mm brass stock to nominally 1.6 mm (1.5 will work too) in a lathe at one end (for accuracy use a centering drill first), cut off at desired length, reverse and put in chuck, drill other end, tap M2 (for brass and good screw retention just using the #1 tap will do; you can drive the chuck and hold the tap holder if you feel brave enough), reverse, tap M2 first end, ready. Sequence may vary slightly.

                                              Great to hear it! From what I read, I had a feeling that not too many of us are making these rare items, and it is such a relieve to find someone who can make it with ease. :tu: :cheers:

                                              1 Reply Last reply
                                              • Vidar Offline
                                                Vidar
                                                Posts: 2,605
                                                Vidar Offline
                                                Vidar
                                                wrote on last edited by
                                                #19 Quote Reply

                                                  @Dutch_Tooler said:
                                                  That said, the more sophisticated, the better is of course true, but perhaps liquid cooling attachments (nozzles and recirc pumps) is pushing the needs beyond those needed for DIY in the SAK and multitool area. And at the precision we are talking about, a Jacobs chuck will do the job admirably and collets will not be strictly necessary IMHO. Depends a bit on how much more you plan to possibly do in future, I guess...

                                                  Yes, I just meant is indicators of more sophisticated gear if he came across something used. Yes, a Jacobs chuck should indeed to fine for this. :cheers:

                                                  I've bought most of the machines I have used, avoiding dealers, and I've rarely had any regrets with that. Price tends to be a fraction of new and used usually comes with most of the basic accessories and then some. The main issue is often documentation and spare parts if needed, so well known brands with live distributors are preferred.

                                                  I actually don't have a drill press these days. Had to move to a smaller place some years ago so I gave it away.

                                                  @Dutch_Tooler said:
                                                  Sourcing sufficiently precise basic machinery is a real concern, I can see that, especially in the smaller sizes for DIY and smaller workshops. My lathe is an Austrian Emco Compact 5 (alas without the hard to get milling attachment) which should suit DIY needs but is no.longer available new.

                                                  I've never used en Emco Compact 5, but it gets high praise everywhere I see. Makes me wonder why they stopped making it? The CNC version of that is sometimes for sale fairly inexpensive sometimes - even for less than the manual version. I guess non-standard controls, collets or something like that might explain that?

                                                  For small stuff I got an Cortini H105 CNC. Still with working original control system! Very precise but not all that much torque. For bigger stuff I have an Nakamura TW10, but sadly I don't have room inside for it these days. Hopefully still ok, and some beautiful day I hope to have it operational again.

                                                  @comis said:
                                                  That's a comforting thought...I think as a hobbyist and a total newbie, it might be prudent to grow my skill before acquiring heavy tools I have yet idea how to make good use of.
                                                  And a big thank you for sharing all those info, this experience will be of great reference down the line. :salute:

                                                  Just start somewhere. :)

                                                  Come to think of it there might be something like a maker space in Hong Kong? Some of those places seem to have lots of equipment people can use. Probably also with some people who knows who to use it :)

                                                  @comis said:
                                                  Vidat and Dutch_Tooler, come to think about it, since you guys have much more experience in lathe and all things machine, how difficult is it to make suitable M2 and M1.5 screw pivots for 93mm?

                                                  I actually don't have a 93mm, so a bit lacking when it comes to their pivots..

                                                  That said I wouldn't make M1.5 simply because it is so little material in the center of the screw. The center of an M1.5 is just about ø1.25mm - that isn't much material to actually hold stuff.

                                                  For M2, if you manage to make a 1.6mm straight hole in the center of the pivot pin you should be off to a good start. Make sure to make the hole long enough to also have room for chips from the tap later. Then use a two or three step tap set and some cutting oil. The difficult part if doing this freehand is to get the tap perfectly straight down the hole. A little jig consisting of a precise steering hole can help. Or if you do get a drill press just put the tap in that for guidance and rotate manually.

                                                  Back out a bit for every rotation to break chips. Take your time - a broken tap might not come out willingly or otherwise.

                                                  I see Dutch already answered while I was typing here :) Just using the #1 tap for screw detention in brass sounds interesting - I'll give that a try sometime. :cheers:

                                                  1 Reply Last reply
                                                  • Vidar Offline
                                                    Vidar
                                                    Posts: 2,605
                                                    Vidar Offline
                                                    Vidar
                                                    wrote on last edited by
                                                    #20 Quote Reply

                                                      @Dutch_Tooler said:
                                                      I bow to your greater training and experience Vidar :salute:

                                                      Not really much to bow to! You should have seen my former collection of "things gone spectacularly wrong and bits of metal which tried to maim or kill me". That is not counting various attempts of electrocuting myself, setting myself on fire, chemical exposures or doing stupid things with heavy machinery. :ahhh Training is clearly lacking, although I guess that might count as experience :D

                                                      1 Reply Last reply
                                                      • Dutch_Tooler Offline
                                                        Dutch_Tooler
                                                        Posts: 4,434
                                                        Dutch_Tooler Offline
                                                        Dutch_Tooler
                                                        wrote on last edited by
                                                        #21 Quote Reply

                                                          :cheers:

                                                          Your remarks about not trying M1.5, leaving enough hole depth for tapping residue and retracting the tap every few turns are spot on, sorry for omitting them in my list.

                                                          As to precision, even drilling and tapping slightly off-axis isn't going to break the bank as long as you don't exaggerate. In addition, what I have found necessary anyway is to make the pivots a little bit longer than necessary, then shortening them to the required length while in position in the knife using a drill bit that has the size of the (tapered) screw head (4.5 mm IIRC) to match its taper and make the head's outer surface flush with the scale (by hand, i.e. drill bit in hand driven chuck and using utmost care).

                                                          This is also one of the reasons that I can't simply work to order - each pivot is fitted in place.

                                                          Edit: don't forget the Loctite...

                                                          1 Reply Last reply
                                                          • Vidar Offline
                                                            Vidar
                                                            Posts: 2,605
                                                            Vidar Offline
                                                            Vidar
                                                            wrote on last edited by
                                                            #22 Quote Reply

                                                              @Dutch_Tooler said:
                                                              As to precision, even drilling and tapping slightly off-axis isn't going to break the bank as long as you don't exaggerate.

                                                              True. I guess I've just had some traumatizing manual tapping experiences, and thus I go about things really carefully if I have to do it. Probably too careful if one considers what the machines do in comparison. I guess I should propose a law: "The more expensive or more finished a part is, the greater the chance of a tap breaking inside a hole". It is right up there with single socks!

                                                              A subsupplier many years ago just put a tapping head on a normal hand drill, eyed it at about 90 degrees, and tapped every hole in sight in a real hurry. That was in aluminium though. Still worked amazingly well - you couldn't even drill at that speed.

                                                              1 Reply Last reply
                                                              • comis Offline
                                                                comis
                                                                Posts: 11,394
                                                                comis Offline
                                                                comis
                                                                wrote on last edited by
                                                                #23 Quote Reply

                                                                  @Vidar said:
                                                                  Come to think of it there might be something like a maker space in Hong Kong? Some of those places seem to have lots of equipment people can use. Probably also with some people who knows who to use it :)

                                                                  I looked pretty hard for that, but mostly what I see are some casual 'workshop', where people just show up for an hour or two, and expect something coming out from it(Watch band making, carved spoon with tools, etc). There might be some classes offered in University, but you probably have to enroll to get to play with the toys, and I'm not sure there is access to the machines afterwards.

                                                                  I guess it is the 'instant noodle' culture, where people just want instant gratification without putting having to put in any real work. :whistle:

                                                                  I don't know whether I can speak for other beginner modders, but to me, modding is not just about making desirable products, but it is also the things you learn and people you get to know which is an adventure in itself. :D

                                                                  1 Reply Last reply
                                                                  • comis Offline
                                                                    comis
                                                                    Posts: 11,394
                                                                    comis Offline
                                                                    comis
                                                                    wrote on last edited by
                                                                    #24 Quote Reply

                                                                      The tapping of pivot sounds rather intense, and am not sure it is way beyond me...maybe someday, if I got hooked so deep that I got a mini lathe, even then I am not sure it will be easy to do. :think:

                                                                      So if I got a decent enough drill press, sounded like drilling out all the tools in the 93mm tools and using the 1/8 pivots from knifekits.com is the way to go...or if I am lucky enough, finding someone who could make those tapped pivots and sell it. :pok: :D

                                                                      1 Reply Last reply
                                                                      • Vidar Offline
                                                                        Vidar
                                                                        Posts: 2,605
                                                                        Vidar Offline
                                                                        Vidar
                                                                        wrote on last edited by
                                                                        #25 Quote Reply

                                                                          @comis said:
                                                                          The tapping of pivot sounds rather intense, and am not sure it is way beyond me...maybe someday, if I got hooked so deep that I got a mini lathe, even then I am not sure it will be easy to do. :think:

                                                                          Ah, just find something to practice a bit on - maybe with some bigger holes at first. There really isn't much to it, and afterwards you'll be making threads and screw stuff together all over the place :D

                                                                          @comis said:
                                                                          So if I got a decent enough drill press, sounded like drilling out all the tools in the 93mm tools and using the 1/8 pivots from knifekits.com is the way to go...or if I am lucky enough, finding someone who could make those tapped pivots and sell it. :pok: :D

                                                                          If the pivot is 3mm just get something actually 3mm? Come to think of it, check out something like "EDM drilling electrode single hole 3.0". A bit of search and you have a some straight rods at exactly 3.0 outer diameter with a ready hole throughout the middle. You just need to make it a little bigger, but it will provide steering. For example this place:
                                                                          https://www.aliexpress.com/item/32681859509.html?productId=32681859509&productSubject=Ziyang-Brass-Electrode-Tube-Single-Hole-3-0-500mm-for-EDM-Drilling-Machine (Make sure to specify "single hole" as for 3mm multi-hole is more common).

                                                                          1 Reply Last reply
                                                                          • Dutch_Tooler Offline
                                                                            Dutch_Tooler
                                                                            Posts: 4,434
                                                                            Dutch_Tooler Offline
                                                                            Dutch_Tooler
                                                                            wrote on last edited by
                                                                            #26 Quote Reply

                                                                              On that latter note, I have bad experiences with pre-made holes... better drill yourself

                                                                              1 Reply Last reply
                                                                              • Vidar Offline
                                                                                Vidar
                                                                                Posts: 2,605
                                                                                Vidar Offline
                                                                                Vidar
                                                                                wrote on last edited by Vidar
                                                                                #27 Quote Reply

                                                                                  @Dutch_Tooler said:
                                                                                  On that latter note, I have bad experiences with pre-made holes... better drill yourself

                                                                                  Do you want to talk about it? :) The holes of an EDM electrode should be exactly in the center throughout.

                                                                                  Edit: Just curious of the issues? Come to think about I might have some EDM electrodes around here somewhere. Probably not 3mm though.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. Gathering thoughts/tools/materials for first mod
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0