Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

ZapWizard's Leatherman Free P4 Mods

Scheduled Pinned Locked Moved Leatherman Tools
513 Posts 1 Posters 158.5k Views
  1. Home
  2. Tool Talk
  3. Leatherman Tools
  4. ZapWizard's Leatherman Free P4 Mods
ZapWizard's Leatherman Free P4 Mods
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • ZapWizard Offline
    ZapWizard
    Posts: 171
    ZapWizard Offline
    ZapWizard
    wrote on last edited by
    #62 Quote Reply

      So I worked last night on the 4mm configuration. I like it enough now that I am ditching the idea of making the flat bit driver, even though I know someone will ask for it eventually.

      One thing was getting the bottle opener profile just right. So why not just copy something already known to work? So I copied the Leatherman Brewzer profile. And then tweaked it also work as a 1/4" hex wrench.
      There was a bit of dead space in the middle, so I added a horizontal 4mm driver as well.

      Finally I went through lots of configurations on the magnets. On my first prototyope the magnets installed via a hole at the bottom of the bit driver pocket. However, that meant every time you install a bit, it would slam into the surface of the magnet. And while magnets looks like solid metal, they aren't. They are nickel plated, sintered powder. And cracking the nickel surface can cause the magnet to break up.

      I tried some side-loading magnet ideas, but they were both ugly, and didn't allow you to ream out the hole using a drill bit. (The material tolerances can vary a bit)

      So instead the magnets install via a deep hole opposite the main bit opening. There is a 1mm thick wall of metal between the magnet and the bit to ensure the bit never strikes the magnet.
      Because the hole is deep, you can stack two magnets to increase the overall holding strength.

      Finally, the hole allowed me to add a 4mm bit driver opening that is accessible even if the tool is fully closed.

      I am happy with the design, and will work on getting it prototyped soon.

      1 Reply Last reply
      • Wspeed Offline
        Wspeed
        Posts: 76,225
        Wspeed Offline
        Wspeed
        wrote on last edited by
        #63 Quote Reply

          That looks excellent :dd: :like: :like:

          1 Reply Last reply
          • Poncho65 Offline
            Poncho65
            Global Moderators
            Posts: 88,523
            Poncho65 Offline
            Poncho65
            Global Moderators
            wrote on last edited by
            #64 Quote Reply

              Very cool, Zap 8) :like:

              1 Reply Last reply
              • Wpgwave Offline
                Wpgwave
                Posts: 11
                Wpgwave Offline
                Wpgwave
                wrote on last edited by
                #65 Quote Reply

                  Make sure you have a P2 version of the holster and bit holder!

                  Sent from my iPhone using Tapatalk

                  1 Reply Last reply
                  • Happy Gilmore Offline
                    Happy Gilmore
                    Posts: 1,065
                    Happy Gilmore Offline
                    Happy Gilmore
                    wrote on last edited by
                    #66 Quote Reply

                      @Wpgwave said:
                      Make sure you have a P2 version of the holster and bit holder!

                      Sent from my iPhone using Tapatalk

                      It should be identical for both. And HOLLY MOLLY that looks incredible! :gimme: :gimme: :gimme:

                      1 Reply Last reply
                      • ZapWizard Offline
                        ZapWizard
                        Posts: 171
                        ZapWizard Offline
                        ZapWizard
                        wrote on last edited by
                        #67 Quote Reply

                          @Wpgwave said:
                          Make sure you have a P2 version of the holster and bit holder!

                          The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
                          The bit holder should work in either model.


                          Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.

                          1 Reply Last reply
                          • Happy Gilmore Offline
                            Happy Gilmore
                            Posts: 1,065
                            Happy Gilmore Offline
                            Happy Gilmore
                            wrote on last edited by Happy Gilmore
                            #68 Quote Reply

                              @ZapWizard said:
                              The P4 holster will not fit the P2. The P2 is thinner, and has some other subtle changes that would make it so I have to design its own (similar) holster. At $120 for the P2, it too much for right now.
                              The bit holder should work in either model.


                              Here is the renderings of the design. It will take a few prototypes to tweak the tolerances, so it won't be out for a few weeks.

                              Truly incredible..one nitpick though, would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool? In other words having it so that the bits didn't go all the way through. Might be too hard with the tool thickness but maybe I'm wrong. Incredible job though.

                              I think going with the 4mm bits is a really really good idea. It also reduces the likelihood of Leatherman getting really annoyed with it since it doesn't use their flat bit system.

                              Replacing a single flat bit from Leatherman is a total pain but for $10 you can get something like this:

                              the extenders and flexable heads would even be usable with the tool you are making.

                              We're u still able to keep the 4mm hole open to be used while closed? If so that's uterly brilliant design.

                              1 Reply Last reply
                              • Wspeed Offline
                                Wspeed
                                Posts: 76,225
                                Wspeed Offline
                                Wspeed
                                wrote on last edited by
                                #69 Quote Reply

                                  That looks excellent :like: :tu:

                                  1 Reply Last reply
                                  • ZapWizard Offline
                                    ZapWizard
                                    Posts: 171
                                    ZapWizard Offline
                                    ZapWizard
                                    wrote on last edited by
                                    #70 Quote Reply

                                      @Happy Gilmore said:
                                      Would it be possible to have some kind of stop for the 4mm hole you have perpendicular to the tool?

                                      We're u still able to keep the 4mm hole open to be used while closed?

                                      Any stop I added to the horizontal wrench would lessen the amount of usable length, or make it usable on one side only. Instead, imagine just putting your finger on the backside, like you might do with a box wrench.

                                      Yes, the deep hole in which you install the magnets into opens up into a second 4mm hex opening at the back.

                                      1 Reply Last reply
                                      • aussieman Offline
                                        aussieman
                                        Posts: 57
                                        aussieman Offline
                                        aussieman
                                        wrote on last edited by
                                        #71 Quote Reply

                                          Love your work...

                                          Before I order, I was thinking of getting the mid mount "Large" size and adding the TheClip.com, Model 661BP

                                          Would that fit ok?

                                          Select "Large" for: Tek Lok compatible hole placement.
                                          ..
                                          Can also attach to other mid-mount Chicago screw style products.

                                          Designed to be compatible with the TheClip.com, Model 661BP
                                          Recommend Tandy Leather, Screw Post Model 1296-04

                                          1 Reply Last reply
                                          • Dutch_Tooler Offline
                                            Dutch_Tooler
                                            Posts: 4,434
                                            Dutch_Tooler Offline
                                            Dutch_Tooler
                                            wrote on last edited by
                                            #72 Quote Reply

                                              @ZapWizard said:

                                              Any stop I added to the horizontal wrench would lessen the amount of usable length, or make it usable on one side only. Instead, imagine just putting your finger on the backside, like you might do with a box wrench.

                                              Yes, the deep hole in which you install the magnets into opens up into a second 4mm hex opening at the back.

                                              :like:

                                              1 Reply Last reply
                                              • ZapWizard Offline
                                                ZapWizard
                                                Posts: 171
                                                ZapWizard Offline
                                                ZapWizard
                                                wrote on last edited by
                                                #73 Quote Reply

                                                  @aussieman said:
                                                  Before I order, I was thinking of getting the mid mount "Large" size and adding the TheClip.com, Model 661BP

                                                  Yes it will mount the metal clip. Rather than fix the chicago screw positions to just Tek-Lok like I did on the Wave, I decided to make it one fixed hole, and one slot. That way more products can be mounted.
                                                  There was a small issue on the Tek-Lok version which might have allowed the bottom edge of the clip to catch, but I updated the 3D model just now. One of the great things about 3D printing is instant changes are possible.

                                                  1 Reply Last reply
                                                  • ZapWizard Offline
                                                    ZapWizard
                                                    Posts: 171
                                                    ZapWizard Offline
                                                    ZapWizard
                                                    wrote on last edited by
                                                    #74 Quote Reply

                                                      I 3D printed a mockup of the bit holder in plastic. I shrunk the 3D model by 3% to emulate the shrinkage that the sintered steel will have.
                                                      The plastic mock-up isn't strong enough to actually use, but it lets me get an idea of the general use.

                                                      The mockup showed that I am damn close on the latching profile. The tool folds out and locks almost as good as the metal implements. I little tweak to the model will hopefully make it fully solid.

                                                      The 1/4" wrench actually works in only one direction, it is sort of ratcheting. I also did a torque test on my earlier steel prototype and the 1/4" opening on it was extremely strong, i may test it to full distruction at some point)
                                                      The mock up also helped me realize that I have some space I am wasting due to the springs on each side. So I altered the profile to be a total of 1.3mm wider, every bit helps with an object this small.

                                                      Finally, I modified the real hex profile to have a better fit, and ensure the end of the bit wouldn't grind against the chicago screw.

                                                      I ordered the bit holder in steel, along with a few other projects I am working on. (Rebar holster)

                                                      1 Reply Last reply
                                                      • Happy Gilmore Offline
                                                        Happy Gilmore
                                                        Posts: 1,065
                                                        Happy Gilmore Offline
                                                        Happy Gilmore
                                                        wrote on last edited by
                                                        #75 Quote Reply

                                                          @ZapWizard said:

                                                          I 3D printed a mockup of the bit holder in plastic. I shrunk the 3D model by 3% to emulate the shrinkage that the sintered steel will have.
                                                          The plastic mock-up isn't strong enough to actually use, but it lets me get an idea of the general use.

                                                          The mockup showed that I am damn close on the latching profile. The tool folds out and locks almost as good as the metal implements. I little tweak to the model will hopefully make it fully solid.

                                                          The 1/4" wrench actually works in only one direction, it is sort of ratcheting. I also did a torque test on my earlier steel prototype and the 1/4" opening on it was extremely strong, i may test it to full distruction at some point)
                                                          The mock up also helped me realize that I have some space I am wasting due to the springs on each side. So I altered the profile to be a total of 1.3mm wider, every bit helps with an object this small.

                                                          Finally, I modified the real hex profile to have a better fit, and ensure the end of the bit wouldn't grind against the chicago screw.

                                                          I ordered the bit holder in steel, along with a few other projects I am working on. (Rebar holster)

                                                          Amazing Work, but honestly I would have removed the tools from the other sided and kept the Philips and pry bar. The 4mm bits really cant apply the torque of those two tools. I'd much rather give up the less robust tools that have questionable strength than the ones I can depend on. but to each their own on this.

                                                          I can't wait to see how this thing looks at the end.

                                                          1 Reply Last reply
                                                          • Dutch_Tooler Offline
                                                            Dutch_Tooler
                                                            Posts: 4,434
                                                            Dutch_Tooler Offline
                                                            Dutch_Tooler
                                                            wrote on last edited by
                                                            #76 Quote Reply

                                                              :2tu: Looking forward to seeing how strong this turns out to be.

                                                              @ZapWizard, mind telling us which 3D printer/ plastic (ABS?) you're using? Looks like some neat printing :tu:

                                                              1 Reply Last reply
                                                              • ZapWizard Offline
                                                                ZapWizard
                                                                Posts: 171
                                                                ZapWizard Offline
                                                                ZapWizard
                                                                wrote on last edited by
                                                                #77 Quote Reply

                                                                  @Dutch_Tooler said:
                                                                  mind telling us which 3D printer/ plastic (ABS?) you're using?

                                                                  The mockup was printed on a Ultmaker 2, 0.4mm nozzle, 0.12mm layers, PLA plastic. It makes very clean prints most of the time. It took about fifteen minutes to dig out all the support material from the internal holes, one of the bad things about FDM printers.

                                                                  1 Reply Last reply
                                                                  • Dutch_Tooler Offline
                                                                    Dutch_Tooler
                                                                    Posts: 4,434
                                                                    Dutch_Tooler Offline
                                                                    Dutch_Tooler
                                                                    wrote on last edited by
                                                                    #78 Quote Reply

                                                                      Thanks ZapWizard :cheers:

                                                                      1 Reply Last reply
                                                                      • jorritvS Offline
                                                                        jorritvS
                                                                        Posts: 75
                                                                        jorritvS Offline
                                                                        jorritvS
                                                                        wrote on last edited by
                                                                        #79 Quote Reply

                                                                          Zapwizard, I have been lurking around for a while and first of all I got to say What an amazing design. And what a beautiful render of the Leatherman P4. Since I use solidworks and inventor myself I know how much work and time such a drawing cost. Really incredible work!
                                                                          I like the design of the bottle opener/ bit driver a lot too. But I can't help to think about an idea that might improve it.

                                                                          At the moment you can us the standard 1/4 inch at the bottle opener position and the 4mm while closed, while open and from the side. My idea is to replace one of those. I don't know if it is possible but maybe you could replace the 4mm hole from the side with a hole that fits the flat leatherman bits. And therefor make the tool accept the 3 I think most used sizes. Again I don't know if it is possible in ways of strength and space but should it be possible I think it can be a real improvement.

                                                                          I hope I didn't disrespect you in any way. That is not my intention at all.

                                                                          Sent from my ONEPLUS A3003 using Tapatalk

                                                                          1 Reply Last reply
                                                                          • ZapWizard Offline
                                                                            ZapWizard
                                                                            Posts: 171
                                                                            ZapWizard Offline
                                                                            ZapWizard
                                                                            wrote on last edited by
                                                                            #80 Quote Reply

                                                                              @jorritvS said:
                                                                              At the moment you can us the standard 1/4 inch at the bottle opener position and the 4mm while closed, while open and from the side. My idea is to replace one of those. I don't know if it is possible but maybe you could replace the 4mm hole from the side with a hole that fits the flat leatherman bits. And therefor make the tool accept the 3 I think most used sizes. Again I don't know if it is possible in ways of strength and space but should it be possible I think it can be a real improvement.

                                                                              I could fit a Leatherman bit holder into that space. Mabye even a combination 4mm, flat bit opening. However, someone who picked up a Free P4 without every owning any other Leatherman won't have any bits, or even necessarily know the flat bits exist. I owned a wave for years before I even knew they sold other bits, I just figured I got Phillips and Flathead. Also, the flat bits can be turned in the 1/4" opening. But it isn't ideal, they lock in one direction, and let go easily in the other.

                                                                              Input and ideas isn't disrespectful at all. This is a two way street, otherwise I would just post to YouTube and ignore all comments.

                                                                              1 Reply Last reply
                                                                              • jorritvS Offline
                                                                                jorritvS
                                                                                Posts: 75
                                                                                jorritvS Offline
                                                                                jorritvS
                                                                                wrote on last edited by
                                                                                #81 Quote Reply

                                                                                  I didn't even thought about combining both flat leatherman and 4mm bits that would be awesome.

                                                                                  The good thing about the flat bits is that they are easy to carry and offer a lot of possibilities.

                                                                                  I understand that not everyone has the leatherman set. But adding the possibility to use can never hurt.
                                                                                  I think a lot of people on the forum have a set for one of the many tools they are designed for. And otherwise can be a good expansion.

                                                                                  But maybe I'm the only one who would like it.

                                                                                  Sent from my ONEPLUS A3003 using Tapatalk

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 3
                                                                                  • 4
                                                                                  • 5
                                                                                  • 6
                                                                                  • 25
                                                                                  • 26
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. Leatherman Tools
                                                                                  4. ZapWizard's Leatherman Free P4 Mods
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0