OOPS! - SAK Production Errors
-
@Rich S said:
When did Vic start sharpening the inside curve of the screw driver? None of my 68 SAKs has the inside of the screw driver sharpened as in the top pic. Or is it just the angle of the pic?
RichRich, per the SAKWiki, it is called a cutting notch and the Soldier 1961 models had them up until 1993 or so. Im sure someone else here can provide more detailed info.

-
@Mechanickal said:
I'll pay you with money that was supposed to be real, but came out with "Monopoly" printed on it

-
@Rich S said:
When did Vic start sharpening the inside curve of the screw driver? None of my 68 SAKs has the inside of the screw driver sharpened as in the top pic. Or is it just the angle of the pic?
Rich@HolyDeuce said:
Rich, per the SAKWiki, it is called a cutting notch and the Soldier 1961 models had them up until 1993 or so. Im sure someone else here can provide more detailed info.
If I'm understanding Rich correctly, I think he means on the cellidor knives? That would be starting in mid '51 with the 'new' US PAT PEND/+PAT can opener. There is supposed to be a time in the late '60s when the sharpened edge was omitted, perhaps briefly.
-
@kamakiri said:
If I'm understanding Rich correctly, I think he means on the cellidor knives? That would be starting in mid '51 with the 'new' US PAT PEND/+PAT can opener. There is supposed to be a time in the late '60s when the sharpened edge was omitted, perhaps briefly.Yeah, I misunderstood. My bad.

-
A $2 million dollar stamp

-
US Post Office could use a $2 mil stamp right about now. Not sure if thatd actually help the cause though

-
Not sure I would call it a production error, but I still find it a bit amusing.

-
@moonweasel said:
Not sure I would call it a production error, but I still find it a bit amusing.

There for a long time, Wengers in Vic packaging were quite common--clearing out old Wenger factory stock?
-
That was my thought

-
Re: my earlier post this thread:
I finally got around to looking through my SAK collection and I did find an Alox Soldier (curses-forgot to check the year) that <u>does</u> have a sharpened inside curve on the screwdriver. Amazing what you find out on the board. :)
Rich -
@Rich S said:
Re: my earlier post this thread:I finally got around to looking through my SAK collection and I did find an Alox Soldier (curses-forgot to check the year) that <u>does</u> have a sharpened inside curve on the screwdriver. Amazing what you find out on the board. :)
RichOh cool, one of the older ones then!

-
@Rich S said:
Re: my earlier post this thread:I finally got around to looking through my SAK collection and I did find an Alox Soldier (curses-forgot to check the year) that <u>does</u> have a sharpened inside curve on the screwdriver. Amazing what you find out on the board. :)
RichHey Rich,
Some of my Pioneers have this too. This early one has both the ground edge and the wire bender/stripper:

And as you note, some earlier Model 1961's. These are both '65's:

And I also have an 84 mm cellidor SAK (Salesman, I think?) that has both the ground stripper edge, and the wire stripping notch (lower right in picture):

I wish Vx still did this to the cap lifter tool. It's a useful feature.
Myron
-
Some of my Pioneers have this too. This early one has both the ground edge and the wire bender/stripper:

And as you note, some earlier Model 1961's. These are both '65's:

And I also have an 84 mm cellidor SAK (Salesman, I think?) that has both the ground stripper edge, and the wire stripping notch (lower right in picture):

I wish Vx still did this to the cap lifter tool. It's a useful feature.
Myron
Very nice SAK’s

-
@moonweasel said:
Not sure I would call it a production error, but I still find it a bit amusing.

It took me a minute to get this
-
'72 246fmaU Champion 'A':


I don't normally chase models with boxes, but how often does one come NIB/MIB with an unsharpened awl? It does have the concave grind, but no edge and no tip grind. And to my knowledge, it wasn't a display model...and everything else is sharp.
-
@fullbreakfast said:
If collecting SAKs was like collecting stamps these would be worth a fortune.Kinda works for the rare functionally defective models like SwissFlame or Autotool.
-
Rediscovered this today on an early '80s Ranger:

And if it's not clear in the pic, the pair of cuts toward the tip aren't as deep, and the tip is deeper than a wood saw should be of this era (post '79 with the bump in the backspring tip) and is 'in line' with the bulk of the saw teeth tips. Minor error, but I think it might have come loose from the jig or perhaps the cutting wheel shattered on that last pair of cuts.
-
@kamakiri said:
Rediscovered this today on an early '80s Ranger:
And if it's not clear in the pic, the pair of cuts toward the tip aren't as deep, and the tip is deeper than a wood saw should be of this era (post '79 with the bump in the backspring tip) and is 'in line' with the bulk of the saw teeth tips. Minor error, but I think it might have come loose from the jig or perhaps the cutting wheel shattered on that last pair of cuts.
expert eyes
doubt I'd catch that 
-
Not sure if it’s really an error.
I’m guessing it’s just worn tools on the production line that couldn’t cut quite close enough and it left a bit of excess material on there.
They were only small flakes so just lightly scraped them off with some ceramic tweezers.
Before:

After:

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login