Gerber Curve Review
-
All implements aside from the knife have some machining marks on the round part of tang that engages the lock bar. When they are opened, friction can be felt between the implement and the lock bar. I attempted to take the tool apart and polish this area. All heads on the tool are Torx bits. The pivot point is a T9, and all others are a smaller T7-ish size. I say “Ish” because a T7 is actually a bit too big, and a T6 is too small. With a considerable amount of downward pressure, you can get a T7 to engage the screws, but they are made out of weak metal. After I began to strip out two of the 4 heads, I gave up.
When using the blade, I hold it in this manner:

You will notice that the blade is angled away from my hand. The shape of the tool forces you to hold it in this manner. This feels strange at first, but uses the belly of the blade effectively. The lock is beneficial here because the handle shape naturally makes you choke up on the blade and brace your thumb on it’s spine. I have cut plastic, cardboard, paper, cloth and 550 cord with the knife. I also whittled a few pieces of wood just to try it out. Aside from it’s obvious lack of size, it cuts quite well. The edge out of box was alright, and with a little touch up it has taken a nice utility edge. If you use the blade, or any function of the tool for an extended period of time, some hot spots will make themselves known. This is not a hard or all day use type of tool.
Now, my biggest gripe- The Phillips driver. You can see in the pictures below that it is thicker than the one on my Gerber Dime and also has a bit of a 3d portion on it’s tip. This tip is too fat and square for the majority of Philips screws I have tried the tool on.

Here you can see how deep the Dime’s driver engages the screw head…

And how shallow the Curve’s is.

With a lot of downward pressure, the Curve’s driver will turn the screw without slipping, but it is very uncomfortable as the bottle opener portion of the handle is pressed hard into the palm of the hand. The lock really comes in handy here, keeping the driver from folding. I will attempt to file the head of the driver down some, to make it more like the one on the Dime.
I have found that this technique using the small flat head works better for breaking Philips head screws loose.

The bottle opener seems to work fine, and usually only requires the user to pry up once on the cap. A few more stubborn caps had to be pried up in two locations.

This tool has no tragic flaws, but multiple small ones that add up and are off putting. It has promising design characteristics, but the execution is poor. It seems Gerber has missed the mark with this one. The real test of any tool or knife is weather or not you would buy it again. In the case of the Gerber Curve, I would not, nor would I recommend it to anyone. Were the Phillips driver improved, the rough machining marks smoothed, better quality screws used and the lock tuned to prevent the free play in the stowed implements when one is used my opinion would be very different. This is an example of 1, and other examples may not display these short comings. I will keep carrying this tool and give it further evaluation. I will update here if anything changes. Thanks for reading.
-
Thanks for the detailed review. It bears a resemblance with the 'beer clip' to the LM style CS which I find excellent along with the Micra. The photos of the Philips driver make the Curve look really poor quality, which is a shame as I like the styling overall. Is the locking feature really necessary on this?
W
-
@wellgate said:
Thanks for the detailed review. It bears a resemblance with the 'beer clip' to the LM style CS which I find excellent along with the Micra. The photos of the Philips driver make the Curve look really poor quality, which is a shame as I like the styling overall. Is the locking feature really necessary on this?W
By no means is it necessary, except for when forcing the Phillips driver to work. Its helpful on the blade because of how the handle makes you grip the tool, but not needed. I think the locking mechanism used here is more of an easy out for Gerber. I believe its easier for them to mass produce than fitting and tuning a back spring. The novelty of locking implements on a tool this size is probably what has led the majority of consumers to purchase the tool, so if that was their intended goal then Gerber have achieved it. I just doubt with the lack of quality on this tool that they will keep the business.
-
Are the majority of people that buy the key ring tools that discerning as you or I? I would imagine that the majority of them are impulse or supplementary purchases. It sounds like it deserves to be just an also-ran though.
On the subject of Philips or Posidrive: if you don't have a good engagement, the tool will torque-out. In the case of Posidrive it is intended to do this in circumstances of over-torquing the fastener. However it does mean that these fasteners need the correct sized tool and be easily damaged by a poor quality one such as you have described.
W
-
Another good overview and good explanations of the issues you had with it. I too had the "Uuu, that's a nice small tool" feeling when I first saw it but after reading reviews and impressions on it I quickly decided to spend my money on something else. :-\
-
This just looks like they ripped a chunk off a suspension and decided to sell it.
-
Another excellent review mate.

-
I have been so close to buying this tool, but I always held off. Now I'm glad I did. The Dime seems like a far superior choice from Gerber in the keychain tool category.
-
I picked this item at MEC, mainly because it looked like a good value. Since then, it has proved to be an indispensable tool. I keep it on my coat, clipped on with it's own combination bottle-opener and carabiner. Ruggedly well-built, it has all the tools you might need to open a package, file down a rough fingernail, turn nearly any type of screw, pry off a lid, or almost anything else. I have used it hundreds of times since I bought it, since it's so easily accessible when you need it. All the attachments even lock in position!
-
Are the tools standard mp600/suspension locking types? If so, it would be easy to juggle tools around and get a real 3D locking phillips driver in there. I'd be okay with getting rid of the eyeglass driver for that.
Charles.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

