Gerber Armbar Owners Club
-
Ooh, can I join now?

-
I just picked up a Gerber Fit. I really like this thing! It's a rather large pocket knife with an LED flashlight (which runs on a triple-a battery thankfully), and it has a locking bit driver, a blade, and scissors. Plus two micro drivers and tweezers. Dunno why it didn't catch on, other than perhaps the bulk, but I like it. I think a nite ize clip will make it rather perfect.
Charles.

-
@ChopperCharles said:
Okay, okay. There are two different versions of these little tools. One is labeled Bibury, the other PowerDelux. Amazon links:https://www.amazon.com/gp/product/B082HNVJTB/
https://www.amazon.com/gp/product/B07Z4DBFXN
Nice find Charles! .7 inches deep is a bit much for my pocket. Can you offer an opinion on how easy it would be to drop a layer or two to slim it down? And maybe a picture of the backspacing.

-
To make it thinner, you'd have to cut the plastic back and shorten the pivots. That doesn't really seem doable without a milling machine. This tool is a hair thicker than a 3-layer Wenger SAK, if you don't count the pivot screw heads. It's not as wide or as long as a Wenger SAK though. It's really a lot smaller than you think. I've attached some comparison photos with a Wenger and Victorinox SAK.
Charles.




-
Thanks Charles. Appreciate it.
-
Why is the price of the Armbar going up?

it's gone from $31 to $41 on Amazon, and almost as much on the Gerber site, ???
-
Not a big fan of this tool to be honest. No locking other than the knife (liner lock works great here). The scissors has this little nub that should have been expanded for ease and comfort of use. My thumb started feeling the pressure of that minuscule curved piece of metal that interfaces with you. My copy appears to cut ok...but the puny little spring is more than useless as my copy appears to be somewhat tight and does't do a good job of springing the two scissor blades apart. I do like the driver however, and the awl is cute and I suppose effective. The bottle opener on the end appears to have the best tactility of the whole tool set. I still cannot phantom why the other tools do not lock, or even snap into place. It is like working with a wet spaghetti noddle.I tried using the driver and it functions good...but wants to always rotate on you simply because there is no snap or locking mechanism. At least you can angle the handle whichever degree you want to get some effective torque I guess.
-
Thanks for your observations, they basically mirror my thoughts. I guess the no-snap on those tools is really intended. I guess I will never understand the thought process behind this decision

-
@SirVicaLot said:
Thanks for your observations, they basically mirror my thoughts. I guess the no-snap on those tools is really intended. I guess I will never understand the thought process behind this decision
Yep, not having bought the tool (yet) but looking at pictures and videos I'd say without a doubt that the no-snap was intentional.... Like the Bassett Trim Trio that I have finally identified after all these years.
Now, why they made that decision, I couldn't say. They've clearly stated that they intend the Armbar to be a backup to a folder. With the Centerdrive being so popular, my guess is they are trying hard not to cannibalize the rest of their product line.
-
But the Center Drive is a HUGE tool. The Armbar is a small pocket knife.
With locking tools and a pocket clip, I would have been interested in the Armbar Drive, and likely would have carried it more than my Center Drive. But alas, it wasn't meant to be.
Charles.
-
@SirVicaLot said:
As you can tell, it is about the same size as a Fieldmaster/HuntsmanI will prolly buy an Armbar someday just because I can't say no to a new toy, and its not expensive (now $29.58 on Amazon Prime), but a 4-layer SAK gives you 3x the tool selection in about the same footprint. So I can't get too tingly about the Armbar.
-
That is certainly true, but I think the bit holder for full size bits takes up a lot of space. There is still room for improvement, and with a little more R&D they could have streamlined it some more.
Honestly, I would consider the Armbar the perfect companion for my bladeless MP600, but in its current state there is no way to carry and enjoy using it
-
I bought a 2nd one by accident. Thinking of adding a pocket clip somehow and possibly EDCing it.
-
@Chako said:
I bought a 2nd one by accident. Thinking of adding a pocket clip somehow and possibly EDCing it.Not sure where... but I saw an aftermarket pocket clip attached to the "front" or "back" instead of the side. Someone was thinking outside the box - hopefully that helps you come up with an idea.

-
That does help.
-
You could also fabricate one yourself and attach it to the “cage” where the knife sits in. Might be able to use screws, or if not possible, you can use heavy duty double sided tape. Works like a charm on my MP400.

-
I found a pair of Nite Ize HipClips with 3M tape backing on Amazon.
-
They should work just fine

-
I've just bought one of these but need to modify it for UK friendly use. Anyone know how to disassmble this> I have tried heating it but one side has a crossnut and the other has the badge but neither side wants to budge?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

