Knot in October GAW
-
Hi Guys
Thanks for all the feedback - and for the research and quotes Nix

I really don't like that name EDK - Sent shivers up my spine!!!! :-[I know/see what you mean about the design of the knot meaning that it is pulled apart when in use
The thing about an abseil is that the load on the knot is pretty gentle (ie the weight of the climber), steady and constant - not like a fall - So maybe this is another reason why the knot is OK for this use!
Oh and just to be clear we would always ab. down a double, not single, rope.So what about the Fig. 8 then ? ???
I have tried to show in the sequence below - How a Fig 8 - Can roll over itself and eventually disappear !! :o
I have only shown this on a single (not interweaved) Fig 8. - I think it would be highly unlikely to happen in an interweaved Fig. 8 - And especially if it has been loaded.
So the series of images below are probably more of a demonstration why you need a long tail, a stopper knot and should pre-tension a knot! !!
The stopper knot (which is also an overhand knot - Hey hey!! ;) ) of course would prevent this happening!!One more post coming about when I would use a Fig 8 in an abseil!!
Also something I have learnt in this thread is how knots weaken the rope and how different knots weaken the rope by different amounts - Interesting
So thanks guys
Hey and you are a caver Nicola? - Fantastic -
I have done a little caving ........ loved it :D
There is a lot of limestone in the UK and the caves are great!! -
@Huntsman said:
I have only shown this on a single (not interweaved) Fig 8. - I think it would be highly unlikely to happen in an interweaved Fig. 8 - And especially if it has been loaded.I've seen recommendations to add stopper knots to figure 8 knots. I've used Figure 8 knots to abseil/rappel and for climbing harnesses and have never had an issue, and after testing Figure 8's I don't see a problem.
However, the earlier words of advice hold true for me:
- tie a neat knot, 2) dress it properly, and 3) pre-tension your knots.
Also, an offset figure 8 knot is not recommended! From what I've read, an offset overhand is preferred to an offset Figure 8 for a number of reasons. But the Offset Figure 8 is a bad idea, too.

-
Hello again,
I don't do much climbing these days ...... sadly :'( - So am really enjoying this opportunity to talk about it a bit !! :D
So when you abseil you should always tie the bottom (open) ends of the rope together - I would use a Fig 8 to do this - with a bit of a tail of course! -
This keeps it neat and tidy and means the rope lengths on either side of the attachment point stay equal lengths.
But most importantly: - It prevents you dropping off the end of the rope when you get to the bottom - Believe it or knot several climbers have died by knot doing this.Here is a great shot of a climb (series of abseils) where I used an overhand knot at the top end of the rope and a Fig 8 at the bottom end.
It's the Old Man of Hoy - Off the North coast of Scotland in the Orkney Islands
Nowhere is it more evident of the need for a stopper knot at the bottom than on this descent.
You can see the bottom abseil says 'free abseil'....If you have regular 50m ropes - When you get to the bottom of the rope you will be dangling in mid air - still about 10m off the ground!!
Hopefully you did not drop off the end of the rope as you had your Fig 8 stopper knot there!!!
So what do you do about that ???If you know about this - ie you researched the route before the climb
[list type=decimal]-
When you climb **up **the Old Man you leave a fixed tether rope from The Haven to the Gallery - So when you do the ab. you put the tether rope through your waist carabiner and abseil slightly diagonally back to The Gallery
-
If you use 60m ropes you get right to the bottom
-
If you did knot know about this - ie It happened when you were doing a route for the first time ......... Maybe my next knot will help you!!

-
-

(Figure 8 is my favorite stopper knot. I was taught to use the Figure 8 as a stopper as a wee tiny sailing lad and have ne'er felt the need to change course. ;) )
-
@ReamerPunch said:
I went through this again.
I already knew the bowline, hangman's knot, single and double fisherman's, clove hitch.
I have learned and am able to tie from memory the Alpine Butterfly, the handcuff knot, break-away lanyard, single and double constrictor.I am impressed with the constrictor knots. Talk about tight. wow. :ahhh I wish someone had taut me these earlier.
Tightening it reminds me of the movie Anaconda. It really looks like the cord is alive. Thanks, Sos24!
And we have three more sets of knots coming! Can't wait!

Glad you like the constrictor knots.
I’ve used the slip constrictor for tying-down items before a big storm
-
I have decided on my next knot, and it's pretty special.

-
T - 1

Or post yesterday if we are on Nix's clock >:D
-
It'll be the 15th in 2.5 hours here.

-
Thanks for the warning. Was waiting until the weekend to post my next one.

-
:ahhh
So....it is 15 October 2020....JAFA time.....

-
ATTENTION!!! ATTENTION!!!
*Time Period Two (2) is now closed!*Time Period Two (2) is now closed!
I say again, Time Period Two (2) is now closed!ATTENTION!!! ATTENTION!!!
-
ATTENTION!!! ATTENTION!!!
*Time Period Three (3) is now Open!*Time Period Three (3) is now Open!
Time Period Three (3) really is now open!ATTENTION!!! ATTENTION!!!
-
:D
I have my spoiler knot picked out..... >:D
But haven't taken my photos yet....! :ahhh
-
To celebrate the end of Time Period Two, I'm going to change the rules again.
So far, I think I've offered the winner of the GAW a difficult choice to make from among a string of three very different fixed blade knives. This week, I'm going to throw another twist into that choice and add a folder. Let's see if this throws someone for a loop.......

Left to right: BRK Vidarr, BRK Bravo 2, ML Knives EDC, BM ContegoChoosing one of these four knives seems like a tough task.

Let me make it a bit easier:
The Contego is an awesome knife. I can scarcely believe I'm offering it as part of the GAW contest. It was designed by the now famous Warren Osborne.
A native of Australia, Osborne moved to Texas, where he resided in Waxahachie for many years. He was a full-time knifemaker and sold his first custom knife in 1980. In his trademark cowboy hat and cowboy boots, Warren was a fixture at knife shows and BladeSports International (BSI) cutting competitions.
Warren passed away far too young, but he left behind a legacy of brilliant knife designs.
This Contego is a Benchmade knife made with Benchmade quality. It is a beast of a knife with a full 4" (10.2 cm) blade made from CPM-M4 steel. The blade shape may not be for everyone, but I think it is particularly useful and functional. Hey, it was designed by a legend who knew what he was doing. The scales are G-10. The Axis lock is buttery smooth and the heavy blade flicks open without a thought. That big piece of M4 has some real inertia when it gets going and carries open or closed (watch those fingers!) with little effort.
Now, let me make the choice a bit harder:
While the Osborne is a practical knife, I think it was designed as a 'tactical' knife. This gives it a few drawbacks. For one, it is big. It carries reasonably well in a pocket with that slightly worn pocket clip. I don't like pocket clips in general, but this knife definitely benefits from a pocket clip. I would say that the ergos of the Contego are excellent (and for my big hands they are); however, that G-10 is very aggressively textured. That may be practical in some situations, but it means the knife isn't all warm and cuddly to hold. (Comparing the sandpaper-like texture of the Contego to the smooth feel of a BRK is like night and day!) I actually used some very fine sandpaper to knock down some of the really sharp bits. (I don't think you can tell from looking at it.)
Another drawback to me is the small pointy glass-breaker that sticks out of the pommel. Again, a nice tactical touch, but I find that it pokes me from time to time. Not a big deal, but I usually find myself, after carrying it for a day, thinking I'd like it better without that sharp bit of carbide sticking up.
While the M4 steel is an amazing knife steel, it isn't the easiest to sharpen. I don't think I've ever sharpened this knife, but I have some experience with other M4 knives.
So: a bit big, a bit pokey, a bit heavy, a tricky steel, and a worn pocket clip. Probably why I don't carry it often.

Still....it is an Osborne....and a Benchmade..... :o
-
You like throwing a curve ball in this GAW, don't you

Sent fra min FRD-L09 via Tapatalk
-
I still know which one I would choose [emoji6]
Sent fra min FRD-L09 via Tapatalk
-
Well....you need to enter a knot first.....

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


