Car boot finds
-
Nice find!
JR -
This Allen wrench set was in the estate sale buy. The box is an old Lucky Strike cigarette box. The owner soldered holders into the box.

-
Thats cool. I like finding things like this. Personal and handy. -
Today's estate sale buy. The vise is a Rigid 500-R. 5 inch jaws. The anvils are inexpensive owner made, but the give me something to bang on. The motor is a GE 1/3 hp.

-
It was hot here and the local market was pumping.
Some of the things I wanted were too expensive but I did get these.
The tenon saw is a Disston Canada (emblem on the other side).
He dropped the total to $23NZD (= $15USD).
-
@Yadda said:
Today's estate sale buy. The vise is a Rigid 500-R. 5 inch jaws. The anvils are inexpensive owner made, but the give me something to bang on. The motor is a GE 1/3 hp.A freaking Ridgid? There so good, I had sooo many pieces of their equipment excluding a tripod, I need a good vice, all I got is some $20 4” the jaws screws don’t even fully tighten, and that one anvil to the left look perfect, I’d so love a nice piece of modified railroad tie!
Nice score!
JR -
@MadPlumbarian said:
A freaking Ridgid? There so good, I had sooo many pieces of their equipment excluding a tripod, I need a good vice, all I got is some $20 4” the jaws screws don’t even fully tighten, and that one anvil to the left look perfect, I’d so love a nice piece of modified railroad tie!
Nice score!
JRThe railroad anvil isn't flat, but I don't do any smithing so it isn't much of an issue. You'll love this part. The Rigid vise was $7.50. It has copper jaw covers. The original jaw inserts look almost brand new. I paid $20, for the three homemade anvils. I bought the whole lot for $34.25.
-
@Syncop8r said:
It was hot here and the local market was pumping.
Some of the things I wanted were too expensive but I did get these.
The tenon saw is a Disston Canada (emblem on the other side).
He dropped the total to $23NZD (= $15USD).Nice buys! Hard to go wrong with a Disston saw. I don't imagine you see too many there.
-
@Yadda said:
The railroad anvil isn't flat, but I don't do any smithing so it isn't much of an issue. You'll love this part. The Rigid vise was $7.50. It has copper jaw covers. The original jaw inserts look almost brand new. I paid $20, for the three homemade anvils. I bought the whole lot for $34.25.Oh I so hate you right now

If we were to look around rather then just sit for 3days trying to sell our own stuff and I came across that vice they would be asking at least $75 or up!
JR -
@MadPlumbarian said:
Oh I so hate you right now
If we were to look around rather then just sit for 3days trying to sell our own stuff and I came across that vice they would be asking at least $75 or up!
JR:D
The vise was still attached to the bench. I had to remove three bolts to get it off. I was the last person on the last day of the sale. No one wants to work for good buys I guess. I'm looking forward to getting the motor running again. It is a General Electric 1/3 hp. I'm hoping to replace the cord and get lucky. For $2.50 it was worth a shot. Looks to be circa 1950's. I have a couple of potential project tools that need a motor.
-
The vise was still attached to the bench. I had to remove three bolts to get it off. I was the last person on the last day of the sale. No one wants to work for good buys I guess. I'm looking forward to getting the motor running again. It is a General Electric 1/3 hp. I'm hoping to replace the cord and get lucky. For $2.50 it was worth a shot. Looks to be circa 1950's. I have a couple of potential project tools that need a motor.
My grandfather used to have his normal workbench, but then he had his motor bench, it had like four nice size motors with a switch box mounted on top to the back but each was a diff setup directly mounted to the motor, I think using a chuck, but one was a wire brush, another a grinder, another a buffing wheel, the unique thing was how they were setup on the bench each was like at a 45° angle / / / / so you had the room to move whatever you were doing..
JR -
@Yadda said:
Nice buys! Hard to go wrong with a Disston saw. I don't imagine you see too many there.Actually, most of the old branded saws I have seen here are Disstons. I have about 5 Disston panel saws awaiting restoration and there were a couple of other Disston tenon/dovetail saws plus a couple of unknown brand ones at the market.
-
@Syncop8r said:
Actually, most of the old branded saws I have seen here are Disstons. I have about 5 Disston panel saws awaiting restoration and there were a couple of other Disston tenon/dovetail saws plus a couple of unknown brand ones at the market.That is interesting. I guess because they had the plant in Canada it made it easier and more cost efficient to ship the saws worldwide.
-
@Sparky415 said:
Very nice haul
Thank you.

-
I've got these about a week ago and forgot to post it here.
The files are Vallorbe, The Footprint style (or Blitz Wrench as we call them here) is a German made Belzer, The plane is a nº4 Stanley made in Brazil with a nº3 lever cap, the duckbills are Brazilian made Belzers, and the adjustable is a Brazilian made Bachert.
@Syncop8r said:
It was hot here and the local market was pumping.
Some of the things I wanted were too expensive but I did get these.
The tenon saw is a Disston Canada (emblem on the other side).
He dropped the total to $23NZD (= $15USD).Those are very nice finds! What's the maker of that saw set?

-
It's a Morrill. I'm not sure if it has a piece missing or not.

It looks like the Improved #1: http://members.acmenet.net/~con12a/saw set website/plier2.htm
I will know more when I have cleaned it up properly as I did see some dates somewhere... -
@Syncop8r said:
It's a Morrill. I'm not sure if it has a piece missing or not.
It looks like the Improved #1: http://members.acmenet.net/~con12a/saw set website/plier2.htm
I will know more when I have cleaned it up properly as I did see some dates somewhere...I was not aware of this site, it's always interesting to see what other people collect. I was not aware of this company either, not really into saw sets but I'll have to get some eventually. But first I need some saws to set.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login