Showcase: Mods to plier-based multitools
-
Here’s a quick little mod for the SOG power pint. I wanted a real flat driver and the bottle opener obliged after a little grinding.
Charles.

-
I have modded a couple of my Leatherman tools. I didn't specifically designate them a new name though.
The Wave has been modded to the specs of a Wave+ (plus the 154cm main blade). Also the wood saw has been replaced with a Victorinox scissor and the Wave scissor with an awl I made from the medium screwdriver.
The Charge Ti started its life as an older model Charge ALX and has been gradually upgraded. 1st the main blade was swapped to a S30V blade, then the pliers have been swapped with a Rebar. Later the Victorinox scissors moved in and the Rebar also donated the awl. And when I got the Titanium scales for cheap on the bay, I replaced them too.
The old Surge was updated to the specs of the new surge, scissors, multiblade holder and pliers head moved in. The frame and the plier head had to be modified a bit to make the new tools fit. Both surges now have the big and the small bit holder (the only mod to the new surge).
The silver Super Tool 300 has the saw replaced with the multiblade holder from the old surge. It also now houses a pair of wave scissors and a big bit holder from a surge, therefore the file had to go. [emoji2373]
The black Super Tool 300 only received a pair of scissors from a Wave.
Finally the silver Rebar donated the pliers head and the awl to the Charge Ti, it got the scissors in return.
The black Rebar received the scissors from a black wave.I also added pictures of my original Supertool, PSTII and original Wave. Those tools where all purchased during deployments, the Supertool and the Wave even got engraved.
The rest of the tools, a wingman, OHT, MUT, Juice Pro and Micra aren't modded.
The holsters are for the two surges (top row) and the wave+ and charge ti (bottom row).I hope you like them. [emoji41][emoji106]







Gesendet von meinem Pixel 5 mit Tapatalk
-
Some excellent pics and modding Berndstein 8)

-
I've finally managed to replace the micro-driver on my Wave+ with an awl that I'm happy with.
I ground down a flat driver from an old Sidekick into an awl that has roughly the same blade length (actually slightly more) than the Victorinox SwissTool's awl, yet still fits the Wave+ WITHOUT interfering with the plier rest tab. If you look closely, you can see a half-circle divot near the bevel, which is the remnant of the flathead driver quick-identification marking that the Sidekick's drivers have.
It turns out that the Sidekick driver is a better shape for awl conversion than the Wave/Charge/Rebar/Blast/Fuse/Kick/Bond/etc. standard large flathead driver because the retrieval tab is located much closer to the pivot on the Sidekick driver, allowing for a longer awl blade (by which I mean, the blade can be inserted deeper into holes before the retrieval tab interferes) relative to the overall tool length.
I did have to grind the retrieval tab flush with the rest of the tools in order for the handles to close all the way.

.jpg)


-
Hey folks, let me introduce you to KickStart. My first entry into modding multitools after drooling over the images in this thread constantly, enjoy the eye candy!
Incase anyone is wondering, the background is a US Army issue blanket that was my father's when he was in.
Higher resolution image: https://imgur.com/a/2ivUODa

-
Excellent mods fellas !

-
Tool Name: Leatherman HardCore
Tool Basis: Leatherman Core
Aim: to adapt the tool set to my EDC needs
Mods: acid etched the handles; acid etched the plier head and then sanded the the polished surfaces to leave the black oxide in the recesses; reprofiled the PE blade to Wharncliffe shape; replaced the SE blade with prybar cut down to fit in handles; removed lanyard and small straigh screwdriver; installed large bit holder from a Surge; ground a chisel edge on the medium straight driver and also ground a wire stripper edge on the shaft of the driver; sharpened the can opener to function as a package opener also
Links: /topic/88061

-
-

What acid did you use for the BO ?
-
Tool Name: Rebar EX
Tool Basis: Leatherman Rebar
Aim: To adapt the toolset to my EDC needs
Mods: Removed lanyard, Phillips driver, awl, and some washers. Installed Surge large bit holder, Ozark Trail Multiforce scissors and can opener, Bercol awl. Modified large straight drive into a chisel, medium straight driver into package opener and scraper.
Link: /topic/88311
-
Tool Name: Knifeless PST
Tool Basis: PST
Aim: To adapt the toolset to my EDC needs
Mods: Acid etched handles with ferric chloride, added pocket clip, reshaped knife blade into awl, removed existing awl and file and replaced them with Ozark Trail Multiforce scissors and diamond file
Link: /topic/88245

-
Great entries, Adam

-
Thanks guys!

-
Hi, everyone,
I've been dealing with a fundamental consideration for a long time: A problem with almost all multitools is that their fold-out screwdrivers, files and saw blades are not really strong. Anyone who tries to loosen a really tight screw with a hinged screwdriver will often end up with a wobbly or broken tool. The files and saws become blunt after regular use or snap off occasionally.
So do multitools necessarily have to be „toys“ that aren't made for really hard work? This is my try to come up with an alternative:
I used a cheap China tool as a basis - not because of its (questionable) high load capacity, but rather because of its low price. First of all, it should only be a design study and my financial resources are limited.




-
I removed all tools and instead inserted a solid steel block on one side, which fitted and screwed exactly into the handle and is additionally riveted with two pins. A quarter inch insert is pinned into the block. With it I can use quarter inch sockets and, with a bit holder, all common screwdriver bits. The axial load limit is now no longer with the axis of the folding tools, but with the torsional stiffness of the pliers handle into which the steel block is inserted.



-
In the other pliers handle I inserted a Bosch system jigsaw blade holder I designed myself. It consists of an M-10 bolt that has been drilled out to 6.3 mm. An M-10 cap nut was modified accordingly to clamp the saw blade in place. This means that all available saw blade types can now be used in the tool. It is not difficult to grind a file blade so that it can be accommodated by the jigsaw blade holder. Then files can also be used.

-
I carry the tool in a belt pouch, along with a selection of bits, a quarter inch bit holder as well as several saw blades and files. With it I can do all the work that can be done by using a conventional multitool. But mine is much more sturdy in comparison. OK, the complete set in the belt pouch weighs around 450 grams - the „toys“ are of course more comfortable to edc! :D


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
