EDC Bit Ratchets
-
:o

I wonder how expensive is it for someone to ship items from the US to Australia?
-

Jackly key-chain ratchet
Weight: 42g
Bit holder with 6 bits: 40g
Length: 60mm
Head width: 19mm
Head clearance with standard bit: 30mm (adds 5mm)
Teeth count: 36
Minimum swing arc: 10°
Bit retention: magnet
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $9 with 6 bits and a bit holder
Bits: Phillips 0/1/2/3, Slotted 4, 1/4" square socket adapterAccessories
The Jackly comes with four Phillips bits, a slotted bit, a square socket adapter, a bit holder with six bit slots, a 10mm split-ring, and a 30mm split-ring. The bits are interesting. They all have a colored, knurled collar. This does assist extraction from the holder and ratchet, and they can also be used as finger spinners.
Dimensions
At 60mm, this is the shortest ratchet yet, with the Ares ratchet being the second shortest, at 85mm. The Jackly is still quite wide and thick. At 42g, this is lightweight, but the Topeak and PK Tools ratchets are a mere 29g.
Teeth Count
The Jackly ratchet shares its design and construction with the GreaTalent ratchet. The Jackly has 36 teeth, for a minimum swing arc of ten degrees. This is not the best, but the short body and low profile head allow for some maneuverability, so not all is lost.Bit Retention
The bits are held in place by a magnet. It is not overly strong, so it will do its job without making bits hard to remove.Bit compatibility
Stubby bits can be removed easily. The ratchet is not compatible with double ended bits.
Switch action
The Jackly ratchet has an oversized and exposed pawl, which is its own switch. It is spring-loaded, and the retention is excellent. When in one position, it will not switch positions by bumping into something. Its sides are also knurled to offer traction when operating it.Ease of use
The Jackly has 36 teeth, which provide a 10 degree minimum swing arc. This is far from impressive, but expected of an inexpensive ratchet of this price. As long as it has enough room to engage a few teeth, this will do. The wheel and pawl engage each other convincingly, with no tolerance issues.
The Jackly has an exposed gear wheel and can be used as a finger wheel for more speed on a somewhat loose fastener. The pawl has a good detent and does not change positions accidentally. The ratchet is rather short, which is understandable, as it is intended for key-chain carry. It has a stocky body with a flared end, which helps fill the hand and be comfortable. It does not provide exceptional comfort or torque, but it is not meant to. As it is, it is perfectly usable for a quick fix.
Construction Quality
Much like the GreaTalent ratchet, the Jackly consists of two metal plates riveted together to hold the internals. It is rather thick and wide compared to other compact ratchets. The lanyard hole end is plastic. This may cause some concern, but the plastic piece is wide and it only houses the pawl's spring. It is not the best arrangement, but it does appear strong enough to hold the spring and a lanyard.
The wheel and pawl have precisely ground teeth and engage perfectly. The pawl has excellent detent in both positions. The lanyard hole is chamfered and will not damage cords. The body plates have some grind marks and a few burrs.Portability
This is the main selling point of this ratchet. It is short, lightweight, has a lanyard hole, and it comes with a key-chain set-up bit holder. Admittedly, we have seen other ratchets that weigh even less. Some even have a pass-through head that allows key-chain carry. Still, the Jackly is the shortest ratchet yet, and will be at home on a key-chain. If you only want a few bits, those can be on your keys as well.
Of course, the ratchet is so short, that it will take little space in an edc pouch.
Value
Costing only $9, there is some undeniable value to this ratchet set. It is short, it has a knurled finger wheel, a good magnet, and a nice lanyard hole. It also comes with a bit holder and six bits.Conclusion
The main attraction of this is the key-chain compatibility. It is not the strongest mini ratchet, or the most fancy. It is not the best when it comes to fit and finish. It does not offer many features. Most if not all ratchet we've seen so far offer more.Still, this ratchet does what it says on the box. It does not win the portability category altogether. There are slimmer, lighter ratchets out there. But it is the shortest and most inexpensive. It works as intended, and it is plenty strong for its intended use.
At $9, with a key-chain bit holder and six bits, it is hard not to recommend this. It will make a nice addition to a key-chain, it works as intended, and at its price point, it will make an excellent little gift or stocking stuffer.

Pros
-Gear wheel is exposed, able to be turned with fingers.
-True key-chain set-up, with short length, large ring hole and double key-ring bit holder.
-Inexpensive.Cons
-Somewhat heavy for its length.
-No warranty or other information of listed brand.
-Structural integrity relies on plastic.If you liked this ratchet, also check out:
-
I received the Wiha mini ratchet.

So the pending reviews are of the Wiha, Rujoi flex-head, Klein, and Ovatt.
-
@ReamerPunch said:
I received the Wiha mini ratchet.
So the pending reviews are of the Wiha, Rujoi flex-head, Klein, and Ovatt.I have both the Wiha and the Klein. Can't wait to hear your opinions on them

-
@ReamerPunch said:
I have decided not to get the Wiha one.
I am glad I decided to get the Wiha. The case is tiny for what it has. I got the TerminatorBlue go-box for $40, and two days later I saw it for $36. :o
Just excellent. Great ratchet, nice locking extension, amazing bit selection, and the tiny case is just sweet.
I am writing the review now. I do recommend this, of course. It is an excellent investment, and miles better than the cheap sets you will find on Amazon. -
Some great choices here and lots of great info, RP

-
A great set of reviews. Hope you don't need that surgery.
-
Thanks, guys!

It looks like I may not need the surgery, which is a huge relief. This is unrelated to my fractured toe, but when it rains, it pours, so what can you do.Question: Why are stubby bits not more of a thing?

I've come to appreciate the Mulwark ratchet more and more, because it comes with 19 bits, of which 13 are stubby bits. These are great. I know it's not that much of a job to just cut down standard bits, and I may end up doing it. Still, what's going on? Amazon has only one stubby bit set, and it's $112. I cannot find anything else. The next best thing is indeed the Mulwark ratchet. -
Here's a breakdown of the ratchets I have so far. Pending reviews are the Wiha, Rujoi flex-head, Ovatt, Klein.
Keep in mind that there are things that do not show up in here. The Titan costs $17, but comes with only two stubby bits. The GreaTalent also costs $17, but it comes with a case, and 36 S2 steel bits. For more information on accessories, ergonomics, fit and finish, etc, refer to the reviews. I am in the process of quantifying the subjective categories.

-
very interesting, as usual :)
-
Just received three more!

Wera Zyklop
Anex low profile ratchet
Jadeshay ratchetSo excited for these!


-

Ovatt Ratchet
(can also be found branded by Ashdel, Funfang, Hilitand, Omninmo, Utoolmart, Weytoll)Weight: 74g
Kit weight: 218g
Length: 105mm
Head width: 24mm
Head clearance with standard bit: 32mm (adds 7mm)
Teeth count: 60
Minimum swing arc: 6°
Bit retention: magnet
Extension bit retention: magnet
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $20 with 10 bits
Bits: Phillips 0 and 2, Slotted 3 and 6, Spanner 4 and 6, Triangle 2.3, Allen 5 and 6, Tri-wing 2Accessories
The Ovatt comes with ten bits, an extension, a plastic carrying case, and a zippered nylon pouch that has a clear plastic presentation side. The case sits in the pouch, with its belt clip exposed. The case can be removed from the pouch and used separately. The bits are stored in a fold-out holder, that is released with a latch. The bits are held in by friction, which is not much, but when this is closed, the bits cannot escape. The extension snaps into place, but the two tines that retain it are already white with stress, and do not inspire confidence. The part that houses the extension has a hole, so users can poke the holder from the underside to release it.
The bits include two spanner bits, a triangle bit, and a tri-wing bit. A little unusual to find such specialty bits in a ratchet kit that is targeted to the bike community.
Dimensions
The Ovatt is a little on the long side of edc ratchets, though certainly not by much. It is rather heavy, at 74g, currently at third place behind the Titan swivel-head at 78g and the Klein at 76g. The Ovatt has the widest head so far, at 24mm. It also adds 7mm to an inserted bit's clearance. All this may result in the Ovatt being just short of accessing a fastener in a tight spot.
Teeth Count
The Ovatt has 60 teeth, which is on the higher side. This gives it a minimum swing arc of six degrees for the head to engage the next tooth and turn a fastener. This would have been fine, but there are many other compact ratchets with much slimmer heads, with the same or even more teeth.Bit Retention
The Ovatt and its extension use magnets to hold bits in place. These are adequate for their purpose. They are not overly weak or strong.Bit compatibility
The ratchet socket is too shallow for double-ended bits to engage.
The extension it comes with is too deep for stubby bits. Double-ended bits will turn, but they barely engage, and have a lot of play.
Switch action
The switch is short but relatively thick. It sits and swings in its own little scallop. It has a good detent and does not seem to change positions when bumped accidentally, which itself is not easy to do.Ease of use
The Ovatt is long, thick, with a coke-bottle shape body. It is nicely rounded and comfortable to hold. It provides a decent amount of torque. It even has a lanyard hole so it can be tethered if needed. It has 60 teeth, which may come in handy if a fastener is in a tight spot. Still, the Ovatt has the widest head yet, so this may cause issues. The head also adds 7mm to a bit's clearance, so stubby bits may be needed to compensate.The knurled finger wheel is thin and much shorter in diameter than the ratchet head. As such, it is extremely difficult to spin it with your fingertips.
To access the bits, the latch mechanism must be pressed down. When doing this, the bit holder shoots open, and because the bits are held in with little friction, they can simply be catapulted across the room. Care must be taken to prevent the bit holder compartment from opening as violently as it does.

Construction Quality
Average. The Ovatt is an inexpensive tool and it shows. The ratchet body has dings, scratches, and imperfections all over. The ratchet mechanism has a lot of wobble in the head. The lanyard hole has a burred edge that will make quick work of cords.The bits are simply painted, and the paint did not survive one single screw.
The extension, much like the ratchet, is covered in dings and scratches.
The nylon sheath is single-stitched and the lining is stitched unevenly and crooked at places. There are already loose threads.
The plastic case is thin and there are stress marks already. The bit holder spring is too strong but the bit retention is very weak. There are burrs and imperfections as well.
Portability
A mixed bag. The case has a belt clip, and the nylon pouch will catch any components that manage to fall out of their spot when on the move. This happens often. Having two mediocre containers working together is an inefficient and inelegant solution. It seems like the nylon pouch was an afterthought, to counter the mediocre plastic case. Any loose components will still remain in the pouch, but that means little. Users will have to open the pouch carefully and be mindful of any items ready to drop.Of course, it does not help that the bit holder shoots out, launching bits away.
The ratchet is a good thickness for multi-tool pouch side-sleeves. It will fit in edc pouches. Tethering will require clips, as the lanyard hole will wear through cords.

Value
A prime example of "you get what you pay for", the Ovatt ratchet is inexpensive and it shows. This was bought for $20, and for that much, it is disappointing. The price has dipped at as low as $14, which is far more appropriate.Conclusion
Mixed bags are not worth it in most cases, but at least there are some positives. The Ovatt is not a mixed bag. The only positives are the 60 teeth, and that it comes with 10 bits and an extension. Poor fit and finish; a below average holder and nylon pouch; black paint for the bits, that did not survive a single screw; ratchet and extension covered in imperfections; a lanyard hole that will wear down any cord that can fit through it; a knurled finger wheel that cannot be turned with fingers; the widest ratchet head we have seen thus far.Does it work? Yes, it does work. You can put bits in it, and use it to turn screws. Is that good? Well, it's not bad, but it was a given that a bit ratchet would be able to use bits. It is thick, long, and round, so it does not do a half-bad job. Still, there is more to a bit ratchet than ratcheting bits. Compared to other ratchets we have seen, the Ovatt offers less than most. Sure, some ratchets have fewer teeth, but even then, they cost less, weighed less, and came in a much better set. Are you actually in the market for a cheap, unbranded bit ratchet? Get the GreaTalent. It costs $17, and comes with 36 S2 steel bits, a nice flat plastic case, and it has a perfectly usable knurled wheel (actually one of the best so far). Not a good enough brand for you? Get the Bosch mini ratchet. It costs $20 too, and comes with 20 S2 steel impact-rated bits, four sockets, an extension, and a nice plastic case.
There are many better options out there, that cost less and offer more. I do not see any reason to recommend the Ovatt over anything else. If you have settled on the Ovatt, keep looking. Go back in this thread and find something else. Keep browsing Amazon. Something better will undoubtedly appear.
Much can be said about the Ovatt bit ratchet; very little will be favorable.
Pros
-High teeth count.
-Bits include spanner, triangle, and tri-point.Cons
-Heavy.
-Knurled finger wheel is hard to operate.
-Average fit and finish.
-Head adds a lot of length to bit.
-Low quality sheath and holder.
-Head is very wide.
-Bit holder compartment spring is too strong; shoots bits away when used.
-Lanyard hole is unfinished and sharp.If you liked this ratchet, you skipped the text and only looked at the pictures, didn't you? Also check out:
-
Damned, when I started reading the review, I thought "cool! that grey and orange case would match nicely with my Juice(s) S2 and Fiskars tools" ...
Then I followed along, got to the conclusion and ... "okay, not for me then"
not all reviewed tools can be good
@ReamerPunch said:
Just received three more!
Wera Zyklop
Anex low profile ratchet
Jadeshay ratchetSo excited for these!

So am I ! (mostly for the Wera, and maybe that blue boxed one, that wouldn't match with above mentioned tools
) -
-
Solid work. Looking for more. Keep going and Im sure to buy one...even though I don't need it.
Sent from my SM-A326U using Tapatalk
-
@m47mu74nt said:
Damned, when I started reading the review, I thought "cool! that grey and orange case would match nicely with my Juice(s) S2 and Fiskars tools" ...
Then I followed along, got to the conclusion and ... "okay, not for me then"
not all reviewed tools can be good
So am I ! (mostly for the Wera, and maybe that blue boxed one, that wouldn't match with above mentioned tools
)Not much orange on it anyway. :D
For an orange case, the Beta, Dewalt, or Gearwrench ones would be fine. That Beta box looks so nice. I wish it was readily available. I'd have reviewed it already.



The one with the blue case, wow. It has some nice things going for it. Very glad I found it able to be shipped to Australia.
-
The Wera Zyklop switch is a tiny Wera Zyklop. :D

-

Klein 65200 Ratchet
Weight: 76g
Length: 109mm
Head width: 20mm
Head clearance with standard bit: 35mm (adds 10mm)
Teeth count: 72
Minimum swing arc: 5°
Bit retention: spring and magnet
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $24 with 5 stubby bits
Bits: Phillips 1 and 2, Slotted 3/16" and 1/4", 1/4" square adapter
Features: 5/16" (8mm) nut driver, 7/8" (22mm) finger loop, knurled finger wheelAccessories
The Klein comes with four stubby bits, a stubby square adapter for sockets, and a tiny bit holder with five slots. The bits are not easy to remove from the bit holder. They are extremely tight, and since they are stubby, they do not have enough material to be grabbed.
Dimensions
The Klein is definitely a little long as far as edc ratchets go, coming in at 109mm. It is also the second heaviest, at 76 grams, behind the Titan swivel-head at 78 grams. The back of the ratchet head has a 5/16" (8mm) nut driver. This makes the head a little thick. The finger loop at the other end also flares out significantly.
Teeth Count
The head has 72 teeth, which is quite high. The ratchet has a minimum swing arc of five degrees for the head to engage the next tooth.Bit Retention
Unique to the Klein, the ratchet head has both a magnet and a spring to keep bits in place. Also, since the back of the head does not have a flush hole, bits can not be pushed from the back to aid removal.
Due to all this, bits are very difficult to remove. Stubby bits are impossible to remove with just fingers.A way to solve this is a small screw inserted through the back. With a bit inserted, the screw will be pushed back a little, but still held in place by the magnet. To remove any bit easily, simply pushing the screw in will disengage the bit from the magnet and spring.
It is always frustrating to have bits stay in the fastener or drop out of the ratchet, but in this case, the retention is unnecessarily strong.Bit compatibility
Double-ended bits do not engage and cannot be turned.
Leatherman bits do engage quite convincingly and can be used to great success. For best results, insert the bits so that the spring engages the bit's sides.
Switch action
The switch is very short and flat. It would be very difficult to have it accidentally bump against something and have the ratchet direction change. It has good retention, and it is very easy to operate.Ease of use
The knurled finger wheel protrudes enough from the head and it is the easiest wheel to operate so far. The ratchet is long and provides excellent torque. The stem is flat compared to the cylindrical ones of most ratchets. This helps with grip and comfort. The finger loop allows for various grip configurations.
The extreme bit retention becomes tiresome rather quickly, but this can be eliminated with a small screw to act as a quick-release button.
The head is narrow and has a high teeth count.
Due to the 5/16" nut driver on the back of the head, the head is arguably taller than is needs to be. It adds 10mm to an inserted bit's clearance, which is the second worst, behind the Titan swivel-head ratchet, which adds 13mm. Stubby bits will aid the Klein in reaching fasteners in tight spots, but it only comes with four, and removing them from the ratchet head requires metallic assistance.
Construction Quality
The Klein mini ratchet is well-made. Its mirror finish is consistent. The ratchet mechanism has good fitment in the head, with very little wobble. All edges are nicely rounded off. The logos and numbers are crisply etched on the body.Portability
Despite being a little long, and a little wide at one end, the Klein carries nicely, thanks to the finger loop. It can be stuffed in a pocket but retrieved easily. It can also accept the thickest of carabiners and cords to be hanged or even tethered to a belt or ring.Because the head is so tall, it does not fit multi-tool pouch side-sleeves. It may fit in a pocket organizer if the webbing is wide enough for the ratchet's head to make it through.

Value
At $24, it is a little sad that the Klein comes with a small bit holder and only five stubby bits. It is definitely a high quality tool, with some nice features, and a few we have not seen before.Conclusion
If nothing else, the Klein mini ratchet is interesting. It has both a magnet and a spring. It has a finger loop that is very useful. The head has a built-in 5/16" nut driver. It has a high teeth count and probably the best knurled finger wheel so far.Having the bit retention be this strong is curious. This is the common spring that is found in high quality mini ratchets, like the Topeak, Prestacycle, Wera, etc. This spring is perfectly capable of keeping bits in place. The magnet makes it harder to use.
The listings for this refer to it as a "slim profile ratchet" and mention its "low profile head". It will certainly reach fasteners in some tight spots, but the body is most definitely the least slim so far. The stem starts flaring out near the loop, and the loop itself flares out to 30mm. Also, because of the nut driver on the back of the head, and because the magnet itself is about 3mm thick, the head on its own is 20mm thick, and with a standard bit inserted the clearance is 35mm. This is probably why it comes with stubby bits, but even then, it comes with only four bits and a socket adapter. There are many other mini ratchets that have a much lower bit clearance.

Klein, Wera, Anex, Topeak, MulwarkIt would have been better if the Klein did not cost $24, or if it came with more accessories. The 5/16" (8mm) nut driver may be useful to some, but it increases the head's thickness and bit clearance significantly. Omitting it would have slimmed down the head, improving the bit clearance. It would have allowed the magnet to be flush with the back of the head, and add a magnetic pick up function.
The Klein ratchet is undoubtedly a high quality tool with a lot to offer. Not everyone needs some of its features. This is only recommended as long as the pros outweigh the cons for you.

Klein, Wera, Anex, Topeak, MulwarkPros
-Good quality.
-High teeth count.
-Excellent ergonomics.
-Finger loop allows various grips and tethering options.Cons
-Head adds 10mm to bit clearance.
-With no bit inserted, the head is 20mm thick.
-Comes with only 5 bits.
-One end is very wide due to finger loop.
-Bit removal is not easy.If you liked this ratchet, also check out:
-
Quite a nice one, but seems it was not meant for EDC but more for specific tasks with the nut driver side and such.
BUT put that awful Phillips screw down and use anything that is not a Phillips screw as a push button


[sorry, I hate these screws] -
Well, this was good timing. I guess that finger loop is even better than I thought.

https://www.youtube.com/watch?v=d4hsIF0KxXI
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



















































