40th Anniversary Garage 5 Club!
-
Looks like you "MacGyvered" it just fine...
-
The awl has been quite awlsome with recumbent trike maintenance. Even had to open a USB-C rubber port that was really stuck in its case. The newer type of awl was the cat's meow. Got the task done, and have been sliding the awl in between wires and hoses to snip a wire tie nice and clean.
Yesterday was making a quarter sized slot in a small canning car to hold change for laundry trips. Used the can opener to pop the slot in and widen the area some.

-
Also used the file to file down a welded area on an aluminum handlebar so the e-assist computer bracket would set better. Need to find a rod to go down the inside to make for better support and lengthen the attachment area. No photos yet.
-
My thanks to FolderBeholder on the lead for screws for the Arc. Got them installed on the Garage #5 which are better than ugly holes. Also stops a possible area that could accumulate debris. A plus would be that these small screws give a slight addition to friction on the Zap Wizard open-face sheath.
Really wished Zap Wizard would get on the ball and make a Fully Armorer Garage #5 case already. He's promised several times in December, across multiple sites & PMs, he was going to have one out in a week. Never happened. Then last two months it was supposedly a custom order, and still nothing. I would not be complaining if my request was a minor issue, but when my multitool slides upwards of 3/4 of an inch, yeah, a bit more serious.
Do not really want to go back to an ugly leather sheath with less features for better tool security.

Zap Wizard does not seem concerned very much. Guess you need to spend lots of money on his site to get noticed. Would spend more once he gets an updated fully armored sheath on his site, as I would like other goodies he has to offer.Am wondering if the File and Saw thumb-hole covers would add more drag on the Zap Wizard sheath?
Zap Wizard has good working sheaths, and I do not have shelf queens -- I use my tools. Yet there is an issue with mine, or the type. Have created a Gorilla Tape flexible band that is in need of replacement soon. It helps somewhat, not a cure. However, the screws do have a slight pressure against the Shapeways sheath that I am hoping will last a while.
Garage #005 Open-Faced Sheath found here.
Temporary remedy for a sliding tool issue. Open-Face Garage #5 tool.

Screws for the Arc installed on a Leatherman 40th Anniversary Multitool

-
Only other way I can see for tool security is to add strong magnets on the end of the sheath. JB Weld time maybe?
Did test this with a hard drive magnet which are 40# semi-curved magnets. And how many of you were tossing hard drives away and did not realize the useful magnets laying inside?
-
No pictures since I only have two hands...
Used Crunch, Spirit, and G#5 converting Rover's Anderson connectors to XT90 & XT60 (battery communications). Swear I need to get a third-hand tool with a magnetic base - if they exist.
Not used the Awl as an awl yet, yet been using it as a small pry tool/ Even helped to remove a GoPro battery that lost its pull tab. Think my Spirit is jealous of that tool implement. ;) My buddy is afraid to use the G#5.


-
Had a rack failure on the recumbent trike and needed to make some adjustments. Three hose clamps helped save a battery connected to the one side of the Low Rider Rack. Used Gorilla tape to help reinforce what I could, then changed the location of the hose clamps to both ends and the middle. Think it will hold but have a new mount coming in.
For now though, I needed to clip the extra long hose clamp tails off. Used the Garage #5 with the Damascus Cutter on these stainless steel clamps. Took two initial squeezes on each side to cut them, and they cut quite well. No breaks or chips! These Damascus cutters did the job. -
I’m in! These are my user tools that aren’t stored in bags, etc.

-
Awesome bunch of users

-
Sweet!
I have been using my Charge and Free P4 at work lately, but yours are a whole 'nother level than mine :ahhh
-
It’s still painful to carry the 005. [emoji15] [emoji1787]
-
It’s so rare and beautiful, that makes it difficult to carry. [emoji1787]
The toolset is incredible, although I replaced the plier head with one that isn’t spring-loaded
-
Will admit that the Garage #5 was the most expensive multitool I have purchased. Charge TTi would be its second.
G#5 looks and feels much better than the lesser Arc model. :D -
I carried mine yesterday for a change.
I wish it flipped open like the other Free series tools, but I only take it out when I’m not expecting much use anyway, so it doesn’t really matter.
I wonder if we’ve seen the end of the Garage releases or if there are more to come.
[attach id=0 msg=2487235]

-
I have wondered the same about the Garage releases
they kinda lost some steam by releasing knives instead of MTs
I would have liked to have seen some different heads on them like they did with the Mr Crunch but I guess that may not happen :-\Great pic BTW

-
Had wondered after that last Garage sale, was it a knife? Forgets. Not been much past different colors of the Skeletool CX bombarding the Inbox.
-
Went back to using the Hidden leather holster. Far more secure when riding and whatnot, with the dual snaps. Have to figure out where I hid the belt clip though...

Do not care for the Garage #5 belt clip, and it does not feel like a sturdy clip, yet it is an extra safeguard. Not sure if there are replacements or 3rd Party clip makers out and about. Would be good to find one that built a lanyard loop (or something) into their clip so as to allow the tool to be clipped onto a belt lanyard.
Slipped in Kristen Van Patten's Tweezers with the thin neodymium magnets. First slid under the tweezers, then saw a pen/scribe addition that only installs under the scissors, thus moved the tweezers underneath the File instead. Ordered a Pen with Scribe addition a bit ago, and bars for the saw and file.

-
Welp, I did find a steel lanyard loop for the Arc that am going to try. Ordered one in Orange as that looked to stand out to me. :D
Listing: Stainless steel lanyard ring kit for Leatherman FREE P2, P4, T2, T4, Bond, Curl, ARC, Batch #005 (V1.2)
.jpg)
-
Well... it happened. :ahhh Broke the awl this evening trying to pop off a plastic bar end.

Was in the process of removing zip ties which this awl excels in. Then was not thinking when popping off a plastic bar end I should of used a different tool or pulled up on the vertical axis instead of horizontal, as I heard a snap. Right before the thread loop it broke.

Was debating. Probably faster if I buy a Free Series Awl and replace it myself rather than send to Leatherman. Not even sure Leatherman has warranties on the Garage #5 / 40th Anniversary multitool or not. Am sure they have the spare part.
Seen the Free Series Awls on eBay around $30 + $10 shipping. Am going to hold off until I pay the bills first.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login