Style CS already apart.....
-
*Progress.... initial cuts made, holes drilled, hole tapped for thumbstud, prefit of thumbstud. New blade is .025" thicker and has almost 1/2" more cutting area.....

Folded.....
* -
Ooooh, this looks interesting!

-
I like it too. Im gonna see if pliers from a squirt will fit.
-
-
Now I am beginning to see the meaning in your username >:D
No multitool is safe :ahhh :ahhh
I too shall watch with interest

-
*More progress. Final shaping done. Blade polished. Slightly concave primary bevel with brushed finish. Serrations cut. Time for some sharpening and then install.....
~ evil ~*


-
Evil doer that looks very very cool mate

In the pics the donor blade looks like it is pivoting on a post
Is there going to be a fastener/bolt taped through that post
.I wonder what you would do too a Leatherman Flair's cocktail fork Mr. Evil (convert it to a proper Devil's pitch fork I reckon :P :P :D :D)
-
nicely done, im impressed

-
@cerbera147 said:
Now I am beginning to see the meaning in your username >:DNo multitool is safe :ahhh :ahhh
*Funny you should say that. Everyone in my real life pretty much says that as well, but not only in regard to multitools... anything and everything that can be modified..... * >:D
@MultiMat said:
Evil doer that looks very very cool mate

In the pics the donor blade looks like it is pivoting on a post
Is there going to be a fastener/bolt taped through that post
.I wonder what you would do too a Leatherman Flair's cocktail fork Mr. Evil (convert it to a proper Devil's pitch fork I reckon :P :P :D :D)
Thanks buddy. The post is the stock post for the tool, although unlike the posts of many other leathermans that are only threaded on one side, the posts on the CS are threaded on both sides. As for the cocktail fork... my slight case of OCD requires anything that I have be kept ultra wicked-sharp..... :D
-
Looks excellent mate, I'm genuinely impressed.

-
*Hey gang. A little more progress....
Brushed finish for whole tool, still with standard screws.....

New re-profiled screws, semi-countersunk into new beveled washers.....

Fabricated an awl with extra deep nail nick, still unsharpened. Comparable in size to a juice awl.....

Fabricated washer so that the knife and awl will not clump together (.005" thickness).....
* -
Amazing work Evil...

-
WOW

You have some serious skills dude!
-
*Hey gang... me again. A little more progress. Completed awl.....
Tapered thickness towards tip. Blade sharp chisel edge. Holes to better compliment the look and style of tool.....

Backside with nail nick.....

As you can see, the new awl is even bigger than that of a Juice XE-6, all in a package considerably smaller.....

~ evil ~*
-
Evil that is the coolest Awl I have ever seen 8) 8) 8)

Interested to see how it fits into the whole package
:D -
*See what happens when an innocent little tool falls into my evil hands lol. This turned out to be one of those projects that I set off to do with no definite plans in mind that changed along the way (always seems to happen). Originally, I contemplated a 2nd layer on the file side with both an awl and perhaps a large flat driver. When I started fabricating the new knife blade, I realized the width of the channel for the knife had a lot of wasted real estate. If you have this tool, look at it and you will see what I mean. If you have seen some of my other mods, I always try to utilize every bit of space possible on all of my multitools. Anyway, I capitalized on this space and decided to put the awl alongside the knife blade. It was a super tight fit and had to do a little discreet work to make clearance. I am very pleased with the outcome so far. Excuse the quality of the pictures. I didn't get a chance to clean up the tool when I took these. I'll clean it up real nice for its final photo shoot after all the modding is done. I'll even post it alongside its big brother Project Skeletool which I have consistently been asked about..... (see sig at bottom of post)
Tool closed. Backside. Up top you can see the nail nick for the awl. Extra deep cut works very well and deploys easily.....

Tool closed. Front side. Awl secretly residing behind the knife blade.....

Knife deployed. Awl folded into tool. Thumbstud works beautifully for one hand opening. If I can easily open it with my big-ass thumb without slicing off my fingertip, chances are anyone else could without any issues.....

Awl deployed. Knife folded into tool. The special washer worked perfectly. No clumping whatsoever. I've had awls on my tools for years and never used them at all. Earlier this year that all changed and now an awl is one of the things I try NOT to be without. Even the new awl makes the standard blade look small. If there is one thing to know about me is that I keep things wicked sharp. This awl is no exception. ....

Both knife and awl deployed so you can see how they compliment one another and the tool itself.....

Yet another view.....

I am loving this little tool more and more. I can already tell that I will be replacing my Micra for EDC when this is done. Now it is time to tend to the other half of the tool. Now that the plastic scale is off, there is no going back (not that I would anyway). I do plan on a second layer, that much I do know. What exactly will I put in that layer and what materials for the scale, etc. I am still unsure of. I will keep you all posted. I will also try and take pics of the other mods I have been getting asked about on some of my other multitools that I haven't posted yet.......
~ evil ~*
-
:o :o 8) 8) 8)

Evil that Awl looks as big as the original main blade :o :D :D :D 8)
GREAT STUFF mate

-
Nice work Evil!

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login