Multitasker Series2, first impressions
-
Like I said, we're still working out the details. With the stepped design it packs sizes in a small space but your limited on the number off sizes. With the pocket wrench 2 option you get both with the design but its rather wide. Shane would rather the wrench be part of the overall design and yet removable. Its hard cause its gong to probably be too wide for the plier handles., I would have it separate but he didn't want it to see like an after thought. A lot of brain storming going on, any ideas we can use?
Sent from my Droid using Tapatalk
-
All that I can suggest is something akin to the Paladin/SOG models with the hex bolt cutouts on the handles; while not removable, that's the closest thing I can think of. :/
Perhaps it would be best to have the wrench as a separate piece; just because the bit carrier is separate doesn't make it look like an afterthought, after all.

-
The width is quite an issue. I agree its better integrated since the point of a multi is to get maximum utility in one item, not filling your pockets or a sheath with a bunch of different tools, may as well just carry the "right" tools then. What is the overall size intended to be? Wave/Charge sized, or something closer to the Powerlock/ Swisstool? Looking at the Series II, there's clearly a lot of potential in the design for a really heavy duty tool, something approaching the ST200 size class might make a lo of sense, which would then alleviate "some" of the spacing constraints.
Only thing I can think of is having a slot opposite of each other in each handle. The wrench could slide into one side or the other, and when you close the handles, the second slot covers the remaining half of the tool forming a storage compartment of sorts, meaning you could use the entire width of the tool, not just one handle. Downside is it'd be uncomfortable to use the pliers without first removing the wrench, but I'd still rather have a slightly-inconvenient-sometimes-on-board storage system than an annoying-all-the-time-having-to-carry-a-second-tool-around system. Imagine the slots in the handle of a Wave, but facing inwards towards one another when the tool is closed, the space created becomes your storage compartment. With the rest of the tools being outside opening, it would only ever be an issue when using the (still amazing) pliers, and realistically if you are using the pliers there's a fair chance you may need to be using the wrench at the same time any way.
Speaking of the pliers, I understand wanting to leave off the standard section, but then doesn't that just make the current design seem way overbuilt for just a set of needle-nose? Feels like a missed opportunity to have probably the best pliers head on the market. That alone could be a massive selling point. I think you should nudge Shane to include a standard section. I know he wants it to stand out, but I'm pretty sure the ball-bearing system and full D2 billet already do that just fine lol.
-
Great photos and review, thanks for sharing! That is a nice looking multitool.

-
Saz makes a good point: I forgot it already has a separate bit holder for the driver that I'm pretty positive will be in the EDC (I hope lol), so in that case I suppose the wrench may as well be separate, maybe engineer a new bit holder that can accommodate the wrench as well and call it a day. Leaves more room on the tool itself for more implements.
-
@thebullfrog said:
Saz makes a good point: I forgot it already has a separate bit holder for the driver that I'm pretty positive will be in the EDC (I hope lol), so in that case I suppose the wrench may as well be separate, maybe engineer a new bit holder that can accommodate the wrench as well and call it a day. Leaves more room on the tool itself for more implements.Actually, I rather like the looks of the current bit holder, personally. I'd just suggest adding a slip pocket behind the multitool on the sheath.

-
I like the current bit holder too, but I (and a lot of other people) also don't like sheath carry any more these days. If I had to I could live with the tool and bit holder in my pocket, but having three separate items would start to get old, especially since I tend to carry a lot of crap in my pocket anyway. It wouldn't really need to change much, just add in a clip on one side for the wrench to slide into. You could retain the same basic design.
-
Wow, great head :o
Nice review Bob and top pics

Soooo its not meant to be taken apart....

-
I agree with Neil (I think)

Damn fine looking head and generally rather lovely tool. I think a civilian version would rock

Excellent review Bob, thank you

-
An EDC version would need to have a large-toothed gripping section in the pliers, no question about it.
(we just need to keep
-ing the designer until he caves in to our superior reasoning! :D) But it needs to be a truly outstanding gripping section, to go along with the rest of the tool, right? :)For instance, here's how NOT to do it:

Even compound leverage can't make up for poorly made gripping teeth. ::)
Now here is an example of the correct way to make a plier's midsection:

-
Wow, those are some aggressive teeth.
-
Even if there were a stair-step wrench built in, needle-nose-only pliers do not appeal to me. I use the grippy middle section on lots of things other than nuts. If forced to choose, I'd rather have that section than wire cutters.
I'm also a little blah on the tanto blade, but it would have less effect on my decision to buy one. A good tanto blade cuts well, I just prefer a knife with a belly for general use. That being said, a tanto can act a lot like a Wharncliffe, and they're fine utility knives as well. As long as the ding-dong blade is locking and OHO, I can live with it.
Sorry if we sound like picky beeeoches, but this tool has the potential to be best of class, and I think everyone has a bit of emotional stake in it, having seen the firearms tools "grow up" here.
-
Very pretty. Can't wait to see what the civilian version looks like.
Also, it's nice to see a multitool company actually take advantage of Chinese manufacturing (ie. good quality possible at a cost very low compared to US-made stuff) like Kershaw and Spyderco have done with knives.
-
@jekostas said:
Also, it's nice to see a multitool company actually take advantage of Chinese manufacturing (ie. good quality possible at a cost very low compared to US-made stuff) like Kershaw and Spyderco have done with knives.Yeah, I'm hoping Multitasker becomes the Fenix of the multitool world. Also any idea about price? How much is the AR version? For a tool of this quality, I would be willing to pay quite a bit, but the only multitool that sells (not lists but actually sells) for more than $100 is the TTi. I guess the MUT will sell for more but it's not really available quite yet.
-
At Brownells, the Gen2 Multitasker is going for $89.99, the Ultralight for $69.99, and the Tube for $40.
-
Yeah, I'm with Slack 100% It NEEDS a reg. pliers section because I also grab a lot of stuff that isn't a nut/bolt with 'em. Same with the tanto blade, could live with it, and it does help the tool stand out that bit more, but for general utility I'd rather have something else. This thing does have the potential to be THE multi-tool of choice, so I think we all just wanna make sure it lives up to the potential it has.
-
looks like an extremely well built tool!
now if you had to choose between this and the LM MUT (which costs twice, btw), which would you get (not regarding the price)?
the MUT just seems a tiny bit better suited for everyday use, the Mulittasker focuses a LOT on shooters it seems.
-
Some more information on another thread I made. I thought it would fit in here nicely as well. Bob, hope you don't mind?
/topic/23876
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login