Gerber Crucial F.A.S.T.
-
I'd really like to get my hands on one of these.

-
Here is a quick look at one of these on youtube.
-
Well Gerber did it again. I have seen this tool in stock and ready to sell. Gerber is definitely starting a good trend with bringing tools out just a week or two after the Shot show.
-
Sweet!
Where did you see it if I might ask? :) -
I saw it on the knifecenter of the internet. The crucial shows in stock the others on pre-order.
-
I just ordered one of these, one of my wholesalers had some, which surprised me actually. It will be my first small Gerber multi but I couldn't resist because:
G10, only multi I'll have with that
assisted open on a tool of this size, only in the industry to my knowledge, Powerassist being much larger
Long drivers
pocket clip
Gerber Lifetime warranty
Torx construction so easy adjustment if something is too tight/looseMy only concern is the blade steel on these. What do you guys figure it is? Are all Gerber multi blades about the same, or do they vary in steel type and just don't tell us? I've been happy with Chinese Buck 420HC (which I think isn't really the touted BOS heat treated 420HC, but a close Chinese equivalent) like on the Xtract and Buck slip joints and Leatherman 420HC, which people say is slightly inferior to domestic Buck 420HC, ect. I would think they use at least as good a steel/heat treat as say Buck's little slip joints from China, which really do hold an edge pretty well by my standards, but you guys probably can tell me.
-
I've been using it for a couple of weeks now and I find it to be a good tool. I was a bit disapointed in the original Crucial, but I like the FAST. The drivers are long enough to be useful and lock open.
The blade steel seems like a 420 steel of some sort- it's definately not a super steel, but I haven't needed to touch it up yet.
Def
-
OK this is coming from me... I AM GLAD THIS GERBER LOOKS LIKW A WINNER.
Uggg I need a shower.
-
Hey since lots of Gerbers are made in China (this one included I believe) why not use 8CR13MoV for blades? It's pretty much AUS 8 equivalent (which would actually be superior to Leatherman's 420HC for edge holding) and wouldn't cost much more, and it's already being made in the country these come from. Just a thought.....
-
@hawkchucker said:
OK this is coming from me... I AM GLAD THIS GERBER LOOKS LIKW A WINNER.Uggg I need a shower.
Don't you feel better now? :D :D
-
Well the problem with the China made products is simple. There is 2 Chinas. I know it sounds strange, but it is wierd how diff manufacturers can have diff results. Take Multitasker and the suspension. Two tools made in china but one is Fantastic anf the other rubbish. The Multitasker is a tank and very well built. Hopefully this is how they decided to go now. You can have some things made well overthere, but you need to as a manufacturer specify that is what you want.
-
You are preaching fancy steels to a guy that doesn't believe in the steel race. I understand that some steels have better performance than others, but I'm happy if it takes a decent edge, cuts what I need to cut and is easily touched up. Beyond that, labels be damned.
Def
-
Well steels do make a difference in stuff, but not in my multis. I am actually happy having them with 420 or lesser like aus6. Multis arnt the do everything they are the thing you use because you are away from your rollaway. I carry premium steels in my knives. so I can live with the lesser steels in multis.
-
Oh I don't need super steel, just something decent, I always thought old Leatherman 420HC was fine and hoping Gerber is at least in that ballpark. On pocket clip tools intended to kinda fill in for EDC knives though it might not be bad for Gerber to upgrade like Leatherman did with the CX stuff. I'm not saying even 154CM mind you, but just something they could advertise like the 8Cr13 stuff or maybe AUS 8 or just something the knife buying public would recognize as a steel they have seen in say a Kershaw or a Byrd or Spyderco or what have you. Don't have to be fancy, just something on par with lots of $20-$30 EDC folders out there that let you know what steel they are using. Heck the Sandvik steels are cheap and easy to blank but really very good and fine grained, 13C26 for example. I do lots of cardboard and tape cutting in my job, so I'll test out the Crucial and report back when I get a chance.
-
Just a bump. Anyone gotten one of these yet?
-
I think Marlinaholic has one.
-
Ebay = $42.98 shipped
<u>I just ordered one</u>, hoping it doesn't get loose like my green original did.......Is there a way to tighten then? I have tried everything and the funky screws wont budge, ( even heated it with a torch to loosen the lock-tight...if any? ) I was hoping to tighten it or shim it.
-
@dangerousatom said:
Ebay = $42.98 shipped<u>I just ordered one</u>, hoping it doesn't get loose like my green original did.......Is there a way to tighten then? I have tried everything and the funky screws wont budge, ( even heated it with a torch to loosen the lock-tight...if any? ) I was hoping to tighten it or shim it.
Howdy Dangerous

You sayin' the knife blade on yours loosened up?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login