Skeletools and FreeStyle
-
I think you are bang on the money there- the CF is tough but not tool tough and I don't think it's load bearing. I was concentrating mostly on pictures, so maybe Bob might have some views on it- he handled it more than I did. I just flipped them around a few times to take pics on different angles and such.
As for the serrations on the blade, I agree they do look like a pretty deep cut but I doubt they'll affect blade strength all that much. This is a light to moderate duty tool, about the same size as a Juice, only with a carabiner stuck to it's backside.
Def
-
@Spoonrobot said:
The CX looks classy.Is that the model with the carbon fiber scale? I assume this is not a load-bearing structure and is similar to the titanium accents on the Charge TTi?
That particular component on the Skeletool-Freestyle series appears to be nothing more than a fancy spacer. Note how Leatherman changes the material, depending upon the model in question:

-
It's more than just a fancy spacer, it's what your hand grips against. It doesn't have to be terribly strong, but it has to be comfortable.
-
Good point Tom. What I meant to emphasize was that this component is not load-bearing, and so therefore folks shold not be concerned about strength when considering the Freestyle with zytel plastic.
By the way here are a couple close-ups of the Freestyle's integrated screwdriver Def was referring to:


Hopefully you can see how that driver is canted on a 45 degree diagonal, allowing it to be longer than if it had been rotated flat to the square shank. Oh, and speaking of square shanks, the intent is to have the Freestyle fit the Leatherman Removable Bit Driver accessory.

Cool, so the Freestyle gets to use bits after all! :)
-
Yeah, LM bits AND regular hex bits - COOL! Although I'm sure others have noticed that both the Removable Bit Extension & the Bit Driver Extension are too deep for regular bits because they're made for the double-ended LM bit. I think I've seen this mentioned here before.
I'm still concerned that you won't get much of a bite on a slotted screwdriver without chewing it up with the Freestyle driver.
-
@Tom Munch said:
I'm still concerned that you won't get much of a bite on a slotted screwdriver without chewing it up with the Freestyle driver.Same concern here. Because while we have seen that "flat" phillips before on the Micra, at least the Micra also had a flathead screwdriver. Whereas on the Freestyle, the one screwdriver is expected to handle both types of screws.
-
I have a bad habit of chewing up screwdrivers. The Freestyle driver looks something I'll destroy in minutes.
-
-
Wading through a ton of pictures here. I just found another one of the Freestyle:

-
I have a bad habit of chewing up screwdrivers. The Freestyle driver looks something I'll destroy in minutes.
It does seem as if a screwdriver designed to work on both flathead screws and phillips screws will not likely be suitable for either one. :-\
It's almost as if they have just attempted to make a point at the end of a metal rod. Perhaps it's not a screwdriver at all but a
. :D -
You know how much I like these tools, but it just struck me how much cooler they would be if that entire end with the carabiner & bit driver was replaced with a ratcheting bit driver & storage for a couple more bits. This may even be a mod that I could do.
-
Wading through a ton of pictures here. I just found another one of the Freestyle:
That's one fine looking letter opener you got there bobby.
-
I really dont like the driver on the freestyle, so I guess I will just stick with the skeletool.
-
I think in time I am going to get all three!!
-
@Tom Munch said:
You know how much I like these tools, but it just struck me how much cooler they would be if that entire end with the carabiner & bit driver was replaced with a ratcheting bit driver & storage for a couple more bits. This may even be a mod that I could do.That sounds like a good idea Tom! :)
-
Seeing all these pics has really whetted my appetite for one or more;and has me thinking that Leatherman has now put pressure on Vic/Wenger to add an Alox model or two to the 111/120mm lines.
-
-
Hoo boy, I'd post all of the pics of the Skeletool, CX and Freestyle we took, but I doubt Photobucket has that much bandwidth and server space! I know I sure don't!
We spent about an hour there, literally, taking pictures of Leatherman tools, and most were the Skeletools and Freestyle, although I did get some pictures of the Genus and maybe some other stuff I don't remember! :P
Def
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
