And so it begins.... (My adventures into Alox!)
-
@Ashley said:
Put me in line for a farmer with scissors in red.
hehe no problem, but I have to perfect my modding first. I'm a perfectionist and if something doesn't turn out just right it bugs me forever. So far so good though, I'm liking the threaded pivots, since the knife can then be serviced easy, even with locktite on the threads.
-
If I may share what I've learned from playing with these pins, I think it's best for the pins to extend into the scales as far as they can. That way all the torque isn't put on those tiny screws. It also helps with assembly as the scales will snap into alignment and stay instead of you having to hold the springs compressed somehow while you get the last screw in place.
I've bought 100 of these screws,
http://www.usaknifemaker.com/index.php?main_page=product_info&cPath=30&products_id=118
and they fit the Alox scale holes perfectly sitting flush with the top of the scale so there's no need to re-sink them. If you put your pins in the collet of a Dremel tool you can spin the ends down and square with emery paper and even thread your screws into it and spin them while giving a light touch with fine emery papers to take out the machine marks. Some polishing compound after the 600 grit and,

they come out quite shiny.
-
@bushidomosquito said:
If I may share what I've learned from playing with these pins, I think it's best for the pins to extend into the scales as far as they can. That way all the torque isn't put on those tiny screws. It also helps with assembly as the scales will snap into alignment and stay instead of you having to hold the springs compressed somehow while you get the last screw in place.I've bought 100 of these screws,
http://www.usaknifemaker.com/index.php?main_page=product_info&cPath=30&products_id=118
I'll have to try the screws you mentioned there, the ones I have a just a tiny bit on the small side, but very close.
Im just realizing with my mockup I didnt get the pins into the scales very much at all, so Id redo them and make them a tad longer and stronger that way too, good tip for sure thanks!
-
Ok, I was excited to do a test fit together of all the parts. Some parts still need final sand and polish, but the major nicks are sanded out of the drilled holes.
Starting from the back side scale with posts.

Plus first layer...


Plus scissors...

Plus opener layer.. no saw layer on this first test mock up, didnt want to push my luck.

Plus top scale!

And some fully assembled shots...




It's close to finished but a few details to tidy up. I still need to grind a little on the scissors back spring as well. I think I like the silver torx screws fine, I might try black to see how it compares.
Cheers!
-

Isn't it awesome to just screw them together knowing that you can pop them right apart again if something needs adjusted? -
@bushidomosquito said:

Isn't it awesome to just screw them together knowing that you can pop them right apart again if something needs adjusted?OMG yes! I didn't have any problems drilling out the springs or parts to 1/8 inch. The tool components for alox SAKS start at 3mm anyhow, so not much material to remove. Small price to pay for easy assembly and servicing!
The only thing I'm wishing is for some screws that looked more like rivets. Maybe the button heads would look better. I could hit the alox scales with a milling bit to square the hole bottoms... hmmm
-
Great job Syph007,, very nice on the torx part!! JR
-
are you using the 93mm saw spring for the scissors? ???
-
@Sidhartha said:
are you using the 93mm saw spring for the scissors? ???Nope, it's one from a 93mm alox solo. They work almost perfect just a little tweaking needed.
-
are you using the 93mm saw spring for the scissors? ???
Nope, it's one from a 93mm alox solo. They work almost perfect just a little tweaking needed.
93mm solo spring perhaps?
-
That looks great!

-
Being able to take this apart easily has already come in handy. The way I mounted the scissors, they were rubbing on the knife blade tip.
And of course I used my trusty SAK ratchet to remove the torx screws!

I flipped the scissors around and this works much much better, smooth action and nothing interferes. The nail nick is also perfectly accessible this way.

And I give you... the Urban Pioneer!


Inner parts still need polishing and screws need locktite, but otherwise finished!
-
@bushidomosquito said:
If I may share what I've learned from playing with these pins, I think it's best for the pins to extend into the scales as far as they can. That way all the torque isn't put on those tiny screws. It also helps with assembly as the scales will snap into alignment and stay instead of you having to hold the springs compressed somehow while you get the last screw in place.Oh boy you were right on the money when you said to get the pivots into the scales as far as possible. I redid my mod and drilled each scale hole with a 1/8 bit, then milled the outside down about 1 mm and used the button head screws. Looks way better now and feels really solid, perfect snap on all tools. The way I had it at first without the pivots actually into the scales would have been awful for the long run.
Really really happy with it now, and the urban pioneer is ready for tomorrow's EDC test run.



-
That looks real good, came out NICE!

-
That looks great! I didn't used to pay any attention to Alox stuff. I just liked the red 91mm SAKs and that was it. Now I'm really into the Alox mods and those dang backtool pins have me wanting to do 91 mods by request only. Once I put a Phillips driver in a 93 that was the end of any reason to carry a 91. 93s have a better awl, stronger blade and the ability to easily adapt the only other 91 tools I wanted which is the scissors and pliers. Not to mention that enlarging the holes is a matter of shaving a minuscule .007"!
One more tip to speed up your disassembly,
http://www.progresstool.com/prod_images_blowup/ba-1446-010-b.jpg
Meisinger 2mm bur. Works like an internal pipe cutter,
http://images.lowes.com/product/converted/017197/017197375163lg.jpgI drill only down past the head portion of the rivet, about 2mm deep. Then the bur gets run around the inside bottom of the hole about 3 times on full Dremel speed with a very light touch and the head pops loose. I broke down 7 SAKs in an hour with no damage to any scale.
-
@bushidomosquito said:
That looks great! I didn't used to pay any attention to Alox stuff. I just liked the red 91mm SAKs and that was it. Now I'm really into the Alox mods and those dang backtool pins have me wanting to do 91 mods by request only. Once I put a Phillips driver in a 93 that was the end of any reason to carry a 91. 93s have a better awl, stronger blade and the ability to easily adapt the only other 91 tools I wanted which is the scissors and pliers. Not to mention that enlarging the holes is a matter of shaving a minuscule .007"!One more tip to speed up your disassembly,
http://www.progresstool.com/prod_images_blowup/ba-1446-010-b.jpg
Meisinger 2mm bur. Works like an internal pipe cutter,
http://images.lowes.com/product/converted/017197/017197375163lg.jpgI drill only down past the head portion of the rivet, about 2mm deep. Then the bur gets run around the inside bottom of the hole about 3 times on full Dremel speed with a very light touch and the head pops loose. I broke down 7 SAKs in an hour with no damage to any scale.
I think I even have that first bit you link, I will have to try it.
This site got me hooked on 93 mm... its so much beefier than 91. Every tool is thicker and stronger... combine that with strong 1/8 inch pivots and extra tools and its a clear winner to me.
I dont even own any 91 mm red knives, the only 91 mm i own is a silvertech huntsman. Alox all the way for me.
Oh ya and enlarging 3mm to 1/8 is very easy, barely feels like even drilling. I'm still on my first carbide bit, so I don't know how long it will go for, but so far so good.
-

Hey
stop drooling on me! JROh yea? Take this sucka.
:D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login