Taylor Brands Schrade ST1
-
Anyone want to take a guess why I didn't write the Taylor review? :P
Def
-
Me? I would never comment publicly on what a crappy company Taylor is... after all, they are very successful bottom feeders!
Def
-
Is that lawsuit's I hear in the distance...
-
Go ahead and sue me... with any luck their lawyers are just as high quality as their products, in which case I've nothing to worry about! :D
Def
-
I've said it before, and I'll say it again- If Taylor would like to put their money where their mouths are, I will happily test any of their tools and if I am proven wrong, I will post it here. As any long time readers of my reviews here and on SOSAKOnline will know, I am not above being proven wrong, so I invite them to give it a shot.
It's an open challenge- lets see if Taylor has the cojones to take me up on it.
Def
-
I would tend to doubt that they would take you up on the offer. My firm belief is that when these companies start to outsource thier tools. Disaster follows. Take in case the Original Schrade, Cammilus(ya watching this Gerber)I would tend to doubt that they would want testing done. It would show what garbage is being made now just to turn a profit.
-
I know, but if their lawyers come a- calling, it's nice to say I offered them the choice to prove me wrong!
Come on Taylor brands, show me what ya got!

Hell, show us all what ya got if you don't trust me. We'll do a pass around and everyone will get a chance to weigh in on your products!
Def
-
I especially noticed the locking notch on the spines of the blades, with looked to have been done somewhat haphazardly with a snag grinder. (below)

They look awful! :(
Here's an American made ST1.

P.S. Does anyone know if Schrade stopped the lamination of the plier jaws during the last days of the ST1 production?
Right before they stopped making the tool I picked one up at Home Depot and seemed to remember it having the rivets for lamination but the plier head was actually just one piece with the rivets as decoration. I sold it a few years ago and don't have any pictures to check.
-
Now they look a bit better. ;)
-
@Spoonrobot said:
P.S. Does anyone know if Schrade stopped the lamination of the plier jaws during the last days of the ST1 production?Right before they stopped making the tool I picked one up at Home Depot and seemed to remember it having the rivets for lamination but the plier head was actually just one piece with the rivets as decoration. I sold it a few years ago and don't have any pictures to check.
Interesting. I wasn't aware of that possibility. :-\
-
P.S. Does anyone know if Schrade stopped the lamination of the plier jaws during the last days of the ST1 production?
Right before they stopped making the tool I picked one up at Home Depot and seemed to remember it having the rivets for lamination but the plier head was actually just one piece with the rivets as decoration. I sold it a few years ago and don't have any pictures to check.
Interesting. I wasn't aware of that possibility. :-\
I've sent the member I sold it to a PM but it has been 2.5 years so he may not have it. If I remember correctly I bought it at Home Depot on clearance for @20$ in mid-2005.
It appears Schrade did a little bit of their own production updating during the ST1 run.


I really wish other companies would datecode their tools. ::)
-
Hmmm, good eye there! Wonder why they would change the lamination pattern like that? (And yes, I wonder which one came first?)
@Spoonrobot said:
I really wish other companies would datecode their tools. ::)Then you're not going to like what we just found out from Leatherman..... :(
-
:-X
At least the enthusiast community is better prepared to date the tools now than in previous years when there wasn't such a cohesive and knowledgeable community.
The poster over on CPF replied that he still has the ToughTool and is going to check it this weekend, I'll update when he responds.
-
Leatherman going to stop datecoding?
-
@hawkchucker said:
Leatherman going to stop datecoding?That would suck. :(
-
Tell me about it. Half the fun is trying to get a tool with all the same dates. I only have 2 of them.
-
A bunch of my LM's have matching codes!
-
@Leatherman123 said:
A bunch of my LM's have matching codes!All of mine match.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login