Modding a Rebar questions
-
@MedusaOblongata said:
Can anyone determine whether it'd be possible to get a Fuse, Blast, or Wave scissors in there if you took out the can opener and lanyard ring or something?
I'm really thinking the Rebar would be a perfect replacement for my Fuse if I can get scissors in it somehow.Folding scissors on the Blast, Fuse, Wave 2004, and Charge models are the same. I started off with a Knifeless Fuse, pictured here alongside a Rebar. (Rebar on left, Fuse on right)

First order of business is to remove the knurled screws that the blades pivot upon. This is relatively easy on the Fuse, as the screw heads protrude nicely from the surface of the handle. It's not so easy on the Rebar, due to the recessed pocket that the screw heads are in. Careful work with two sets of needlenose pliers can get the job done, but it takes a steady hand. Having a friend hold the Rebar while you use the pliers to loosen the screws helps.
A word of caution: Both the Rebar and the Fuse use a pivot axle that has small flats on it. When loosening, do not turn the axle or you will strip out the flats in the handle holes. Instead only turn the screw.

It is impossible to tell which is the axle and which is the screw though..?
So remember: on the Rebar, the axle head will be on the side of the handle which has no markings. On the Fuse, the axle head will be on the side of the handle stamped LEATHERMAN FUSE. -
Once the pivot axle is removed, all the blades come spilling out in a pile. I always take a photo of the blades/tools BEFORE disassembly, as later it can be quite difficult remembering which order they were in. :P
Adding scissors to a Rebar:
Note that because of the thumb pad, Leatherman scissors have to be installed along the <u>right hand</u> side of the handle, as seen in the Fuse below:

On the Rebar, one handle has a file on the right hand side, and the other handle has a saw. Both knife blades are on the <u>left side</u> of their respective handles. But not to worry, if you wish to remove a knife blade in order to make room for your scissors, simply put the saw or file over on the left side, as both of these tools have slots going all the way thru them instead of nail nicks, meaning they will work just fine on either side of the handle. :)
So, the scissor tool is two pieces (the scissors and the spring) which have a thickness of .100" (or 2.5mm) But the knife blade is only .070" thick, which doesn't create enough space. And removing the lanyard ring too, which is .060" thick, creates TOO much space.
The solution is to find a small washer or spacer at the hardware store that measures about .030" thick.IN: scissors + washer = .130" (3.25mm) OUT: knife + lanyard ring = .130" (3.25mm)

A quick re-assembly job and Presto! the Rebar has scissors, right? :)

Unfortunately NO, there are a couple minor issues. :( :(
Problem #1, the screwdrivers and awl on the Rebar are a bit longer, and the thumb pad on the scissors gets in the way. (see photo below) Thankfully, it looks like a simple fix to grind away a small portion of the thumb pad to clear, or alternatively you could grind back the screwdriver a short ways.

Problem #2, the scissor does not fold all the way into the handle. See how high it protrudes above the other blades?(see below)

Folding open the blades reveals the problem; It is held up on the underside, by the pivot "bump" of the lock release lever:

The other long blades of the Rebar have a small V-notch cut into them, in order to clear the pivot bump.

Fortunately, I'm sure it would be a simple matter to grind a V-notch relief into the scissor as well, which would allow it to close completely. :)

So being a collector, I have no interest in completing the Rebar scissor mod myself, but I can see no major obstacles for those who would like to give it a try.

-
Excellent stuff Bob, thank you

-
-
Well, I'd have to lose the serrated blade too, so was wondering what else might fit in to that gap?
-
@nuphoria said:
Well, I'd have to lose the serrated blade too, so was wondering what else might fit in to that gap?Well, lots of other stuff would fit in the gap, but the Rebar has such a nice tool compliment already, there aren't many Leatherman options left to choose from.

Hmmm, how about a SOG serrated line cutter? (lock notch would have to be widened, not a big deal)

-
Excellent thread Bob..

Now I* really * need to get my hands on a Rebar... :ahhh -
superb walk through Bob.

-
Well, I'd have to lose the serrated blade too, so was wondering what else might fit in to that gap?
Well, lots of other stuff would fit in the gap, but the Rebar has such a nice tool compliment already, there aren't many Leatherman options left to choose from.

Hmmm, how about a SOG serrated line cutter? (lock notch would have to be widened, not a big deal)
That's still considered to be a knife over here I suspect, but the SOG V-Cutter might work instead... hmm...
You're right that a Rebar has the basics covered well, but I hadn't considered SOG bits. This is why I asked you :D
-
Thanks Bob, very interesting. I do not have any interest in modding the Rebar but interesting to see any way.
:) -
Thx! You're awesome

-
@J-sews said:
Hi Eric,
I didn't try it, but the plier heads look to be completely interchangeable. Here is a photo of a Fuse laying on top of a Rebar:
Here are the same two tools, with the plier heads directly in line with each other. The size and shape of each is identical, except for the "jowls" on the Rebar head that serve to reinforce the wire cutter insert pockets:

Pivot diameters and widths are identical:

This only means one thing my friends...the search continues for 2 BO and a stainless Rebar. I haven't seen them in canada yet, but we are always about a month behind.
I WONDER if there will be a problem with the 'jowls' like the Surge/ST300 head swap. You need to remove the blade safety spring locks to accomodate the width of the head. I am anxious to see if these'll work.
thanks Bob.
-
Very helpful thread! I just wanted to comment on the cutout that would be necessary for the scissors. If I understand this correctly, in order for the scissors to sit flush when they are closed, the notch needed in them would have to be made right on the cutting edge of the scissors, because the scissors would be in the fully open position as apposed to the closed position as shown?
Ben
-
This is too tempting, I'm going to have to order a Rebar and use the head to try and make a ReCharge.
Are there any caveats on Charge disassembly?
-
@turnsouth said:
This is too tempting, I'm going to have to order a Rebar and use the head to try and make a ReCharge.Are there any caveats on Charge disassembly?
Use two bits. Heat the pivot up a bit to loosen the loctite.
The plier pivots are round so need to worry about stripping a flat portion.
-
@J-sews said:
Folding scissors on the Blast, Fuse, Wave 2004, and Charge models are the same. I started off with a Knifeless Fuse, pictured here alongside a Rebar. (Rebar on left, Fuse on right)
That part ticked me off bit. You do know that this is Multitool.org right?

:D
-
He has to clarify for all those
suspension ownersMultitool beginners that may be reading. -
-
@diracismyhero said:
Very helpful thread! I just wanted to comment on the cutout that would be necessary for the scissors. If I understand this correctly, in order for the scissors to sit flush when they are closed, the notch needed in them would have to be made right on the cutting edge of the scissors, because the scissors would be in the fully open position as apposed to the closed position as shown?Ben
Hi Ben,
yes, the scissors are closed in the photo, but the clearance notch would have to be made right where I've indicated with the white circle.

-
Since, when the scissors are folded into the tool, they are in the fully open position, would the necessary clearance notch cut into the cutting edge of the scissor blade?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login