Sharpening SAK'S with Lansky
-
Captain
I would try going back a grit and <u>using a sharpie</u> (I also use a desk light and magnifier) the first time you use it on a blade you will need more time with the coarse stones, I know on Utube they only take 30 seconds ::)
Not to be rude but maybe you need more patience and time at the beginning?

When I first got my lansky system I practiced on my Spartan, I have a 17* and a 20* edge on the two blades and just use a leather strop now :)
Good luck

-
I've found that too - the first time you sharpen a blade on the Lansky you effectively have to re-profile the edge to set it to the angle you're using.
It takes a while, but worth it in the end.
-
The first few times a sharpie and a lo powered magnifier are handy , nice to see where you are hitting .
That pretty much goes for any system . Second piece of advice , practice on reasonable quality paring knives ( Vic. , or Henkels with the cast plastic handles - cost about $3.95 ) .
Chris
-
Thank you everyone for all the great advice.

I have a desk light setup as well as a magnifying glass handy. I will definitely use a sharpie to find out what exactly is going on.
@sparky415 said:
CaptainNot to be rude but maybe you need more patience and time at the beginning?

Good luck

I definitely agree with you there. The thing that I don't understand is I used the same Lansky sharpener to put a pretty good edge on a old Spyderco Delica. Everything worked out great and it was actually the first time I ever used the Lansky. Once I try and sharpen a SAK it just never works out. I do completely agree I need to be patient.

-
Good luck with it Mate

-
@mvyrmnd said:
I've found that too - the first time you sharpen a blade on the Lansky you effectively have to re-profile the edge to set it to the angle you're using.It takes a while, but worth it in the end.
This for me is the problem with using the Lansky. If you try to sharpen a different knife, or grip it different to last time, you have to remove a lot of material before you get anywhere near the edge. Getting a Lansky was the best thing I did regarding knife sharpening, because it taught me I need to learn how to sharpen freehand. As it happens I still use the Lansky from time to time ... for reprofiling
-
@50ft-trad said:
I've found that too - the first time you sharpen a blade on the Lansky you effectively have to re-profile the edge to set it to the angle you're using.
It takes a while, but worth it in the end.
This for me is the problem with using the Lansky. If you try to sharpen a different knife, or grip it different to last time, you have to remove a lot of material before you get anywhere near the edge. Getting a Lansky was the best thing I did regarding knife sharpening, because it taught me I need to learn how to sharpen freehand. As it happens I still use the Lansky from time to time ... for reprofiling
I'm thinking this might be what happens to me, but only time will tell.
-
Amici,
Add me to the club of unsatisfied Lansky users. The time I owned one which was quite a few years ago, I was never a big fan of the results. Also as a southpaw, I found it a tad cumbersome.. Next in my book will be a Spyderco Sharpmaker, since I've heard nothing but great results..Cheers,
Serge -
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..
-
@EddieEnzyme said:
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..I though Vic's grind was 25 Degrees?
I definitely could be wrong though. -
@EddieEnzyme said:
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..I did the initial marker grind test and 25 on the dot.
-
I'm sure I read somewhere that Vic's factory grind is 30 Degrees, meaning that the Lansky's 25 degrees won't actually be touching the edge, more the "shoulders" of the edge until the angle is eventually reprofiled..
I did the initial marker grind test and 25 on the dot.
Ah well, that's that idea out of the window.
Heh heh!
-
Aha - found it!
From Victorinox.com, care and preservation section:
Sharpening
Re-sharpen using a whetstone at an angle of 15° - 20°. This will result in a cutting angle of 30° - 40°. If sharpening on a grinding wheel, always cool with plenty of water to avoid excessive temperatures.
I knew I wasn't going mental.
-
I just received my lansky delux system and try to sharp a GAK aitor and basically same problem as the first post, could no sharp as good as I would like, I will continue trying but probably need more practice and correct angle, probably a little reprofile...So, I will continue trying/practice
-
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.
On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
-
@Aleister said:
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
You know what's funny is that I just sharpened a leatherman charge AL with a 154cm blade and it was bang on 25 degrees. The best thing I think about lanskys is that it gives you repeatable results. Same angle all the time.
-
@Frankctz said:
I just received my lansky delux system and try to sharp a GAK aitor and basically same problem as the first post, could no sharp as good as I would like, I will continue trying but probably need more practice and correct angle, probably a little reprofile...So, I will continue trying/practiceDo you use a sharpy along the edge? I find it really does help

-
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.
On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
You know what's funny is that I just sharpened a leatherman charge AL with a 154cm blade and it was bang on 25 degrees. The best thing I think about lanskys is that it gives you repeatable results. Same angle all the time.
This is what initially attracted me to the Lansky. I just need some more practice I guess. :D I marked the edge on a SAK and i'm going to see whats really going on.
-
I am having great and fast results sharpening SAKs with lansky 5-stone sharpening kit (usually I use just 280 and then 1000 hones for retouching), leathermans are another story though.
On the other hand, I am finding myself using manually the lansky hones (or other sharpening stones) on my knives more and more as I am learning how to manually sharpen knives.
So, even if Lansky slowly becomes less useful for me, it helped me learn how to manually sharpen knives better. Just like using training wheels to learn how to ride a bike.
You know what's funny is that I just sharpened a leatherman charge AL with a 154cm blade and it was bang on 25 degrees. The best thing I think about lanskys is that it gives you repeatable results. Same angle all the time.
I haven't tried a Charge yet but I tried a Juice with not much luck and a couple of days ago a Squirt (black is sharpened, red is never sharpened):

I started sharpening the black Squirt at 30o and I couldn't make it really sharp. Then I tried reprofiling it to 25o and I still couldn't make it really sharp (I think you can "see" my determination on the blade's sharpening :D ). Then, I manually used a 280 stone at both sides of the blade (default sharpening is on one side only) and after two hits per side, it became really sharp.
Now, don't get me wrong, I like the Lansky system, I just haven't figured out yet how to make it work perfectly with some blades.
-
I got the blade on my Charge TTi and Kershaw JYD2 phonebook paper slicing sharp with the Lansky system, but others for some reason just refuse to get sharp...
It's the irony of this system. Perfectly repeatable results, sometimes.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login