The Black Tide (Ultimate BO Wave)
-
@MedusaOblongata said:
When is Leatherman going to hire you?They don't need to.. I'm sure they'll get the exact same ideas all by themself at some point.. ;)
-
But we all saw it here first. Pretty sure I am the first to combine the rebar head onto a wave.
My next grail will be a modded Ti with rebar head etc etc :)
-
Another sweet mod Metroman

-
Very nice adaptation, I love that it folds and closes as well..
-Mus
-
I am going to build one myself a little different. Thanks for the tutorial

-
@tattoosteve99 said:
I am going to build one myself a little different. Thanks for the tutorial
Someone had to do it!
I am very very happy with mine, the dual bit drivers have already come into use with this stupid rental house, the renovator was an idiot. Wood screws everywhere...drywall screws in wrong places...yikes!
-
Well mine will have an awl instead of a can opener. May replace the scissors I don't use them much anyway.
-
@tattoosteve99 said:
Well mine will have an awl instead of a can opener. May replace the scissors I don't use them much anyway.You didn't look carefully :). There IS an awl. You'll have to grind away some of the cutting edge of the awl to fit. It's thicker than the flat bit driver. The second bit driver had to be shaved down a bit too.
-
Wow! Lots of coolness going on in this thread. That mini driver adaptation is genius and your reports read like a romance novel for MT modders.
-
Sorry I'm a little late to this party Eric, but kudos to you for some fine mod work!
And while I enjoyed the Black Tide tutorial immensely, I thought this was pure genius: 
@Metropolicity said:
Had a bit of time today...procrastinating.I took an older style small bit driver from a broken TTi and saw the potential. The newer versions don't have enough material to support this.
A little grinding, shaping and down to a 600 wet sand, we have the little driver driver.
Fits inside the bit adaptor..and the storage up top for the bit works like intended.
Slips inside the bit driver on the Black Tide nicely.
It even folds ups and nests, and closes up too!
As a bonus...the extender makes it a nice little precision one for ACTUALLY fixing glasses:
-
@J-sews said:
Sorry I'm a little late to this party Eric, but kudos to you for some fine mod work!
And while I enjoyed the Black Tide tutorial immensely, I thought this was pure genius: 
Thanks Bob, as always, nice to get a professionals approval :)
I have been putting the Black Tide through it's paces in the last week, fixing up things in this 100 year old rental we are leaving in a few weeks time. Can't wait to get out of this crap for bricks house.
-
Those mini bit drivers look like the ones you sent me 3 of along with the large one. I like using the bit for SAK corkscrew drivers but I have no use for the holder if you'd like them back since you've figured out an awesome mod for them. Otherwise I'll just sell them to someone else that wants to try it or they'll rust away in my parts bin.
-
@bushidomosquito said:
Those mini bit drivers look like the ones you sent me 3 of along with the large one. I like using the bit for SAK corkscrew drivers but I have no use for the holder if you'd like them back since you've figured out an awesome mod for them. Otherwise I'll just sell them to someone else that wants to try it or they'll rust away in my parts bin.I'll take those if Metro don't. :D
-
@bushidomosquito said:
Those mini bit drivers look like the ones you sent me 3 of along with the large one. I like using the bit for SAK corkscrew drivers but I have no use for the holder if you'd like them back since you've figured out an awesome mod for them. Otherwise I'll just sell them to someone else that wants to try it or they'll rust away in my parts bin.emailed! I want those back if you don't want em..I'll make more bit drivers and pawn them off on MTO members :)
-
The Black Tide muscled its way through a ton of tasks today!
Used The Black Tide's Robertson, Phillips and flat head bits to install a new light, remove screws from the wall, reinstall a cleaned heating vent, tightening up the storm door hinges and tighten up the BBQ's loose screw. I also used the saw to cut down a zip tied hardware piece we used to hang up a pendant light, the SE blade to cut down some rope we had up and the PE blade to cut open a bun for BBQ burgers.
The new 154cm wirecutters drew their first blood by cutting the support wire for the pendant lamp.
-
Did the Rebar pliers just drop in, or did you have to make some adjustments?
And of course the awl. I had to fit one from an ST300 in there with a Dremel but I think took off more than what was needed. As I tried to explain to someone at Leatherman, why carry two tools when one would suffice?
*Am assuming the Charge is perty much like the Wave spec wise. Already voided the warranty on my Charge TTi, what's another tool? The replaceable wire cutters would save from having wire cutting issues that the Charge/Wave have as stock now.
*Besides, I take good care of my tools. ;)
Want them to be ready when I need them, not having to go running back to the house or the car. That's the whole reason of carrying a multitool isn't it, having what you <u>need</u> with you at all times? -
The heads just dropped in! So bizarre.
However; scissors are a no go. Anything shorter than a bit driver will fit when closed :)
I should say that having both Robbie and Philips bits have been invaluable in the last two weeks.
-
These new pliers practically eliminate that one sore problem of the wire cutters locking the pliers up.
Where was that ReCharge thread...
Wished I had a small shop, the tools, and the funds to redo mine. Getting the tools lined up without munging a washer is my biggest worry. Hmm... wonder if a Surge blade exchanger could replace the file/saw, and add the scissors on the outside of a TTi. Would make more sense.
Surge is nice, just too heavy for EDC. Leatherman made a smaller version of the Super Tool 300, surely they could do the same with the Surge ..... unless a modder does it first.
-
@Xelkos said:
Hmm... wonder if a Surge blade exchanger could replace the file/saw, and add the scissors on the outside of a TTi. Would make more sense.Surge is nice, just too heavy for EDC. Leatherman made a smaller version of the Super Tool 300, surely they could do the same with the Surge ..... unless a modder does it first.
Nope. Not yet.
I fiddled with a blade exchanger but it's huge for the slot and to have the saw/file inside the tool would render them about 2" long. Not too useful. I am going to see about milling my own. But not till my new shop is up and running.
I have a candidate for scissors to replace the saw, BO ones from a Gerber Flik. The pivot is the same already and all it needs is a pin to hold the back spring in place.
Failing that, I have some Cerakoted Vic Scissors on the way that I know will drop in with a pivot expansion.
-
Now I wonder where you are getting those from ???? ;)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login