The Black Tide (Ultimate BO Wave)
-
@Xelkos said:
Now I wonder where you are getting those from ???? ;)
Yes, extra bulge from the plier head support material interferes with it.
Hmm, did not notice that at first. Wonder if Leatherman skipped the rounded facing of the pliers for strength, or just to skip a step in processing just to get them out the door in time for sales?
The extra material removed for the 154cm cutters need to be bolstered by support material, otherwise...snapperroo!
They aren't cast poorly so there is a level of finishing because there is a flashing line along the sides as well as a sprue that has been ground off. The Rebar plier head has been ground flush after they've pressed together like the other LM plier heads, but only the two faces have been ground.
If you are looking for sharp and nicely cast plier heads for future mods, I would invest in a few pairs of Rebars now. I've seen some really poor casting on those TTi scales as of late, so I suspect that Leatherman is fond of using their casting dies past their prime.
That being said...these have been engineered with a LOT of lessons learned from the ST300 plier heads and take direct design cues from it.
-
I was scraping and picking at the drain yesterday with a dental pick and I thought...oooooo finally a worthy substitution for the silly can opener I never use.
I took the original small bit driver and fitted it next to the big bit driver. Taking the small bit itself and heated it up to cherry red with my butane torch, bent it a bit, then reheat, then bend some more and repeat once more to get a 90 degree bend. Tempering the bit left if brittle so I heated it again till cherry red on most of it (while holding it with vice grips) and dropped it into some oil to quench it and return it to it's flexible hardness (scale or hardness is unknown).
Cutting the bit down to fit inside the handle while close, I sharpened it to a point.
A couple of drops of super glue made this a permanent installation.
So much more useful than the can opener!
-
@Metropolicity said:
I was scraping and picking at the drain yesterday with a dental pick and I thought...oooooo finally a worthy substitution for the silly can opener I never use.I took the original small bit driver and fitted it next to the big bit driver. Taking the small bit itself and heated it up to cherry red with my butane torch, bent it a bit, then reheat, then bend some more and repeat once more to get a 90 degree bend. Tempering the bit left if brittle so I heated it again till cherry red on most of it (while holding it with vice grips) and dropped it into some oil to quench it and return it to it's flexible hardness (scale or hardness is unknown).
Cutting the bit down to fit inside the handle while close, I sharpened it to a point.
A couple of drops of super glue made this a permanent installation.
So much more useful than the can opener!
Now put it in the oven at 500f for one hour and that will draw it back to the appropriate temper.
-
Not really a mod but definitely a hidden storage spot!
I was thinking..there much be some room for a pair of tweezers some where on this giant tool. I mean if they found a place for it on a tiny Vic Compact.
Sure enough, yes there was. I tried with a Vic Compact tweezer, while it fit, the plastic head peeked out too much, plus it wasn't black ;)
SOOOO that brings me to my never used BO Gerber Dime, with it's BO Tweezers.

The thing about the Gerber tweezers is that they slanted on the top, perfect I thought.

Sliding them into the pocket clip slot on the end of the Black Tide on the Saw side (the Saw is thinner, more room). Upside down so the slant follows the curve of the handle.

You can JUST make it out...black on black doesn't show up well but they are nested inside the radius of the bent sheet metal.

And push em all the way in! They are next to invisible!

They are JUST shallow enough not to interfere with the bit driver opening.

One more to drive the concept home :)...the useless Dime is now tossed aside till I figure out what to do with it. It's done it's job for now.

-
Another great idea metro. Now that gives me one.
-
@tattoosteve99 said:
Another great idea metro. Now that gives me one.I was actually going to PM you about it but I figure you'd see it anyways :)
I think if we milled out a thin notch on the steel butt end a Vic one could fit..however...unsure.
-
Damn, man, you're quite the mad scientist. Well done!
I'd be afraid that they're resting against the end of the saw blade, and that when the saw is opened, they'd spring out into the space the saw occupied. Have you tested to make are they don't interfere with closing the saw?
-
@Gryffin said:
Damn, man, you're quite the mad scientist. Well done!I'd be afraid that they're resting against the end of the saw blade, and that when the saw is opened, they'd spring out into the space the saw occupied. Have you tested to make are they don't interfere with closing the saw?
They don't interfere with the saw, however, they do interfere with the file (much thicker than the saw).
I had to swap the saw and file placements so I can use the clip the way I want (with the PE blade on the same side as the clip). It's reverse than most standard load outs but it works great. PE/Saw on the same handle and the the Hook SE/File on the other.
-
Do you think some tweezers from a LM style would work? Those are sold separately
-
Wenger tweezeers are slanted too.

-
Do you think some tweezers from a LM style would work? Those are sold separately
I tried, the head on them is flat and you need a slanted head to make it flush with the handles.
Good news is that most Gerber Dime's are $15-18 :)
the tweezers on the style(not PS or CS) have a slanted head and cost 2$ http://www.leatherman.com/accessories/product/Replacement_Tweezers_for_Style
-
Do you think some tweezers from a LM style would work? Those are sold separately
I tried, the head on them is flat and you need a slanted head to make it flush with the handles.
Good news is that most Gerber Dime's are $15-18 :)
the tweezers on the style(not PS or CS) have a slanted head and cost 2$ http://www.leatherman.com/accessories/product/Replacement_Tweezers_for_Style
OOOO! I was mistaken! I was looking at my PS and you are right!
Do it my friends...you'll pulling out splinters out like a pro!
-
Wenger tweezeers are slanted too.

Don't they have a plastic head tho? Thy would stick out.
Noup, flush metal.
Victorinox large, Wenger large and Style CS tweezers.

-
Hi Metro, is that grip/skateboard tape on the lock release tab?
Looks to be an effective addition.
-

Hi Metro, is that grip/skateboard tape on the lock release tab?
Looks to be an effective addition.
That is indeed skateboard tape. It is not so much for the lock release, its more to aid my pinch grip so I can extract it from my sheath easier. The jimping/ridges on the release do great for its actual purpose.
I put the Black Tide 'fat' side down so the flat portions of the lock release are where my fingers natural go to get it.
-
Well I decided to give it a go myself on my Charge AL(used to be an X).
I use the leather sheath and keep it skinny side down so I put the grip tape on the fat end.

When I use the pocket clip its quite a tight fit but now with the addition of the grip tape extraction of the tool is much easier.

Provides nice traction when using both knife blades, thumb on one side, index finger on the other.
Cheers for the top tip Eric. Looking forward to seeing what you have instore for the Black Tide next.
-
@colinoutdoors said:
Well I decided to give it a go myself on my Charge AL(used to be an X).I use the leather sheath and keep it skinny side down so I put the grip tape on the fat end.

When I use the pocket clip its quite a tight fit but now with the addition of the grip tape extraction of the tool is much easier.

Provides nice traction when using both knife blades, thumb on one side, index finger on the other.
Cheers for the top tip Eric. Looking forward to seeing what you have instore for the Black Tide next.
I often thought about adding a bit of tape on those parts too, BUT I ride the Black Tide up against my Black Space Pen, in no time I am sure it'll show brass in MUCH shorter time than it already has.
I like that it's super cheap and effective :)
I wish they had continued that jimping all the way up the release button so these kinds of 'fixes' don't have to be discovered by us.
-
@colinoutdoors said:
When I use the pocket clip its quite a tight fit but now with the addition of the grip tape extraction of the tool is much easier.That's why I carry mine the same way as Metro; not only are the lock tabs easier to grab hold of, but I also leave the clip outside the body of the sheath; that way the tool is always in the same orientation, so the OHO blades are always where I expect them to be, and the clip doesn't make the tool any harder to draw.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login