And so it begins.... (My adventures into Alox!)
-
@crackout said:
I was thinking about trying a pivot mod next as well.
However, since I'm from metric Germany (:P) I think I'll make some custom 3mm diameter pivots myself. How big is the hole in the Alox tools?You guys redrill to get 1/8 inch, which is around 3.17mm. If I make 3mm pivots, will they fit directly?
I know I would have to drill the 91mm tools, but what about the 93 ones?Oh, one more thing: If I get a Farmer and replace the saw for scissors (can't go with a Pioneer, because I need the liner), do I even need a solo spring or can the saw spring handle it as well?
Now you're hooked! You'll be ordering donor knives left and right now! :D
For hole sizes.
Standard 93 mm alox - Tool holes are 3mm, center spring hole is 2.5mm
Standard 91 mm - Tool holes are 2.5mmSo.. if you made 3mm pivots you can use directly on the 93mm alox frame for the tools, and just have to drill the 91mm tools out to 3mm and that would be perfect. You will also have to drill the center springs to 3mm from 2.5 as I dont recommend trying to make a tiny 2.5mm pivot, just make up all 3mm pivots and you will have me jealous! :D
The pivots I use are 1/8 inch hardened steel with 2-56 threading all the way through in a single threaded cut.
A saw spring would be too thin to use with scissors, unless you didnt mind a gap, which I would and it would bug me... if you aren't as picky you can add washers and it will be functional. But I sense you would want it perfect as well... :D
Happy to help with any other tips, just let me know. Also if you get 3mm pivots made up, I'll be quite jealous and might have to finally do that myself. I buy them in bulk for about $1.50 USD each though, so I don't know how many Id have to get made up to make custom 3mm ones cost effective. Of course if you have a lathe and can drill and tap your own, and harden them that works too!
Cheers!
-
I'll have some 3mm pivots made with a M2 threading inside.
The only thing I'm still not sure about is the material I should use for the pivots. The drill bits for cutting threads this small are extremely fragile so you can't really use hardened steel in the first place.
I think I'll go for a standard stainless steel. Let's see.Screwwise I'll use the button shaped ones, however they don't seem to be that common here in Germany.

Button heads would be the one on the left, while the one on the right is called a "Linsenschraube" (lentil screw). The slant part however could compromise the fit.
A lot to fiddle around still. :D
-
These pivots I have are 302 Stainless, spring tempered. You want to end up with something somewhat similar in hardness to the SAK tools I would think, so you don't get one galling the other.
Then again the Vic nickel silver pivots are quite a bit softer than the tools so they would be yielding to any tool wear... hmm maybe it would only matter after a very long time. Or maybe it would matter more on a pivot since the walls are much thinner.For screw style I prefer the countersunk type, so they are flush with the scale surface. Feels nicer in hand.
Regardless Im curious to see what you come up with!

-
I ordered a Solo and a Farmer. Will use the scissors from my Compact's donor Explorer.
Exciting stuff. :)I will send the scales of the Solo to my anodizer to have them PulseCoat treated. It's a special hard anodize he does exclusively.
Here's a shot of a yoyo we had done with this technique:

@Syph007 said:
For screw style I prefer the countersunk type, so they are flush with the scale surface. Feels nicer in hand.So you don't use button srews? But I guess you still have the pivots go into the scales and not flush with the last tool?
-
Well I have no fingerprints left from all the sanding, but I got the Ti urban pioneer finished. All Ti except the springs and tools. :D It turned out darn nice I think.
It looks like a SAK from the future... ;)






-
WOW!
-
very pretty... and shiny :D

-
Very nice!
Sent from my Galaxy Nexus using Tapatalk 2
-
Very nice Syph007, as always very impressive! JR
-
Just excellent... a total evolution of the SAK

-
Titanium scales and liners? Start having blades made from s30v or 154cm, and you might be able to quit your day job...beautiful work.
Sent from my ADR6400L using Tapatalk 2
-
I´ve got a lathe i want to get rid of.... A 1960s (or maybe earlier) Hahn & Kolb - Just can´t find a box to fit it in and i guess it won´t fit into a Mailbox....
I´m looking to sell it to get a smalelr bench lathe, this one is about 400 kg and i only use it to turn a spacer once in a while or to refurb Starter Motor´s collectors.
Nice work btw, any chance to make more of those pivots, Crackout? I might want some...
-
More pivots maybe, but not by hand. It takes too long and therefore noone could pay for them.
I could have them CNCed, but then I need a larger quantity. At least 50 I think. -
A few more things I'm currently thinking about.
I hate the keyring spacer so much. It ruins the entire smooth feel of the alox models. Can someone hook me up with a non-ring spacer, maybe?
I'm still waiting for my Donor-Solo to arrive and I was wondering what blades they used before discontinuing this model. I read on the Wiki that some came with bent blades and some had straight ones. Since I will use the Solo spring for the scissors layer of the Pioneer, the Solo blade always had the replacement blade role. I'm hoping for a bent blade on mine. Anyone with insight in which blades were used at what time?
Next thing: Awl replacements. There's this Settler Pioneer that sports a small blade. However, it's sold out everywhere. I guess these small blades are as thick as the awls? Using a small blade from the 91mm range is no workaround for me. It's just not sturdy enough to go along with the rest of the Pioneer. That said, I'm highly interested in blade layer tools (small blade, pruner or electrician); if someone doesn't need them anymore. :)
Tomorrow, the screws (and hopefully the Solo) arrive. Exciting!
-
Ok I can sense your enthusiasm and mod addiction growing! LOL. Ok some answers for you.
When people request to have no keyring on a custom, I use a liner as a guide and scribe a smooth line on the keying part to show where to remove the nub. Grind that off, then sand and polish and you wont even know that part used to have a nub.
Solo blades came in a variatey of krink (bent) stages. None of then will fit in a multilayer alox as is however, whether they are perfectly straight or bent. If you look at a farmer/pioneer the main blade actually extends into the area above the liner, meaning on a solo it would be in the scale. That being said Ive put a bend in a blade from a solo to fit, you just have be careful but the blades do bend. Clamp it protected in a vice, and use a mallot. Ive tweaked a few tools this way by a few degrees.
Ive never had a settler, and only use the 91 mm small blades for mods needing small blades. If you want a thicker short blade, Id go looking at an 91 main blade and cut that down to shape, add a nail nick etc. You can use tools thicker than the awl, and use a thinner spacer too.
Electricians blade and pruner will fit in there as well, but will need some tweaking. They are hard to come by now though since those are all discontinued models. Im going to have to start making electricians blades from 91mm main blades. There isnt a great way to mod a pruner from another blade, but luckily that type was way less popular than the electrician.
Happy modding! :D
-
@crackout said:
A few more things I'm currently thinking about.I hate the keyring spacer so much. It ruins the entire smooth feel of the alox models. Can someone hook me up with a non-ring spacer, maybe?
I'm still waiting for my Donor-Solo to arrive and I was wondering what blades they used before discontinuing this model. I read on the Wiki that some came with bent blades and some had straight ones. Since I will use the Solo spring for the scissors layer of the Pioneer, the Solo blade always had the replacement blade role. I'm hoping for a bent blade on mine. Anyone with insight in which blades were used at what time?
Next thing: Awl replacements. There's this Settler Pioneer that sports a small blade. However, it's sold out everywhere. I guess these small blades are as thick as the awls? Using a small blade from the 91mm range is no workaround for me. It's just not sturdy enough to go along with the rest of the Pioneer. That said, I'm highly interested in blade layer tools (small blade, pruner or electrician); if someone doesn't need them anymore. :)
Tomorrow, the screws (and hopefully the Solo) arrive. Exciting!
I'm parting 3 ringless farmers this week so I can hook you up with the ringless spacers and a pruner blade as well as some extra liners if you need them. Just PM me.
-
@Syph007 said:
Ok I can sense your enthusiasm and mod addiction growing! LOL.It's getting worse any minute. :D
When people request to have no keyring on a custom, I use a liner as a guide and scribe a smooth line on the keying part to show where to remove the nub. Grind that off, then sand and polish and you wont even know that part used to have a nub.
That was the plan, however the grinder I have access to is pretty darn garbage (see what I did to that phillips :P). That's why I was looking for a stock one.
Solo blades came in a variatey of krink (bent) stages. None of then will fit in a multilayer alox as is however, whether they are perfectly straight or bent. If you look at a farmer/pioneer the main blade actually extends into the area above the liner, meaning on a solo it would be in the scale. That being said Ive put a bend in a blade from a solo to fit, you just have be careful but the blades do bend. Clamp it protected in a vice, and use a mallot. Ive tweaked a few tools this way by a few degrees.
That's tragic. Then I guess I'll have to bend it. So you really use instant force (hits with a hammer) to achive a bent instead of a continuous pushing?
@bushidomosquito said:
I'm parting 3 ringless farmers this week so I can hook you up with the ringless spacers and a pruner blade as well as some extra liners if you need them. Just PM me.Sir, PM sent.
-
Would this work, Electrician blade, large blade, scissors, cap lifter, phillips. I am working on a red scale with brass liner for an edc. Love having an awl but thinking a small blade would get used more.
-
@nj2656 said:
Would this work, Electrician blade, large blade, scissors, cap lifter, phillips. I am working on a red scale with brass liner for an edc. Love having an awl but thinking a small blade would get used more.Yep that tools combo would work. The electricians blade needs a tweak in the other direction, but it will fit. Same as the pruner blade needs that to nest in with the main blade.
-
But only those pruner blades that are mounted in the caplifter layer normally.
There are Pioneers that already have the blades nested next to the large blade (Settler, Pruner, Apprentice).


Or am I wrong?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login