What did you use your Leatherman for today?
-
That's the one big downside to non-locking tools and ,unfortunately, why the PST won't get lots of use for screwdriver jobs.
I still love it though :D
If you want to do screwdriver jobs with a PST you could get yourself a LM tool adapter, they made one that works very well with a PST (the original version with two tangs, not the later "Universal tool adapter" with no tangs). Then you can use any std 1/4" hex bits.
Thanks for the info
I will have to look into that.Today I used the PST II's knife blade to cut up a bunch of cardboard left over from the baby crib and bouncer seat I assembled yesterday. It was very sharp and worked very well, even on the tip of my thumb :-[
-
I used the PST II's pliers to break up a plastic hanger that had broken and was no longer usable. Also used the Rebar's wire cutters to cut some wire that was holding some fake flowers together on a "bouquet" made for my wife's baby shower at work.
-
I used the pliers on two Leatherman tools, a new Wave and a Blast too straighten the slightly bent corkscrew on a vintage Victorinox Rainier (partially serrated blade).
I used the Wave pliers to hold the base of the corkscrew and the Blast pliers to gently bend the top of the corkscrew slightly to one side so it cleared the liner better.
Is there a prize for using multi tools to fix other multi tools?
Tony
-
Used the flat driver on the Splash (Fat squirt) to change out a snapped needle on Betty today.

The Splash hanging out with Betty. Now that's a real looking woman.

-
Back to the fence. Got home and the dog was out. Fencing came off post. Twisted some wire around a post with my Sidekick.
-
Well this story is actually from yesterday, but I didn't get the chance to get on here last night.
While I was delivering some supplies to the main office here at work, the UPS guy drove in to pick up any packages and whatnot from the dropoff box. As I was exiting the building, he asked me if I had a phillips screwdriver in the truck he'd seen me unloading from. There are no tools in that company vehicle, so I happily replied, "No, but I have one on me." He asked, "Oh, you have a Leatherman on you?" To which I proudly replied, "Yes I do."
So I reached into my back pocket, pulled out my Rebar, got the phillips screwdriver out and handed it to him. He needed to remove the lock from the dropoff box as it had been broken for some time and no other driver had bothered to fix it. He mentioned that he normally has a Leatherman on him, but had forgotten it that day.
Let that be a lesson learned, do not forget your multitool(s) each morning :D -
@Metropolicity said:
Used the flat driver on the Splash (Fat squirt) to change out a snapped needle on Betty today.The Splash hanging out with Betty. Now that's a real looking woman.

Wish I new how to Wolf Whistle in text.
-
Should put that in the Woman Thread

-
Goofing around with my mut.

-
Used my Leatherman Juice Pro scissors to cut some Gorilla Tape, used to reinforce/secure the bed liner piece on my truck's tailgate.
-
I just used the Juice CS4's pliers to pull a slippery headphone plug out of the headphone jack of my husband's phone. Any small plier would have worked, but the Juice was nearest to hand.
-
Used my S2 to hold grill burner parts while I used a Dremel barrel grinder to clean them up prior to using Loktite to put them back together.
Sent from Endor using Schlapatok

-
This wasn't today; it was over 10 years ago in fact, but here's what happened:
I had left a cast iron frypan on the stove for a bit too long, and when I came back is fully engulfed in flame. The handle was too hot, I didn't have a potholder handy, so I whipped out my Leatherman, and used the pliers to carry the flaming pan to the sink. It also set the curtains on fire, so I ripped them down also. I was able to eventually douse the flames, and then I used the Leatherman again to put up new curtains. I only had a few minor burns on my hands to deal with. -
Replaced a mobile cellphone booster today. I didn't realize they become obsolete along with the phones. Someone had zip-tied the wires very securely under the seat with big thick zip-ties. If there was ever a time I wished for side-cutters it was today. I could only cut them by feel, and I had to use my Juice knife. Very scary indeed.
-
I used my wingman wire cutters to break off a pair of metal zipper pulls on a small utility pouch. They jingled with movement, really annoying. Then I used the needle nose pliers to pull some paracord through and knotted them as new zipper pulls. No more noise with movement. :D
-
Took apart a lighting control board with my S2. I had to clean the sliders out with some canned air.
Sent from Endor using Schlapatok

-
Worked on some Amphenol plugs for electronic equipment at work. I always have my Super Tool 300 with me here.
<img src="http://farm9.staticflickr.com/8185/8427935952_5e543f3c82_b.jpg">
<img src="http://farm9.staticflickr.com/8377/8427955124_61472349b2_b.jpg">
<img src="http://farm9.staticflickr.com/8326/8427946936_6a332c845c_b.jpg">
<img src="http://farm9.staticflickr.com/8515/8427951060_6832b6a4be_b.jpg"> -
Used my wave to adjust my dremel so I could grind pretzel sticks to make a model car out of food. (Bet you don't hear that often!)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
