Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

The Splash - LM Squirt Mod

Scheduled Pinned Locked Moved The Mod Squad
361 Posts 1 Posters 78.4k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. The Splash - LM Squirt Mod
The Splash - LM Squirt Mod
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Metropolicity Offline
    Metropolicity
    Posts: 3,797
    Metropolicity Offline
    Metropolicity
    wrote on last edited by
    #169 Quote Reply

      @nuphoria said:
      Absolutely brilliant stuff.... can't wait to see the next set of scales :D

      Oh, and about the selling of tools, I'm always here to take them off your hands! :whistle:

      I am going to work on a set of stuff to sell on Shapeways, something you can drop in with the simple ordering of the 1/2" pivots. Making these available to anyone with a good bit of patience, steady hands and a paypal account. :D

      1 Reply Last reply
      • nuphoria Offline
        nuphoria
        Admin Team
        Posts: 15,038
        nuphoria Offline
        nuphoria
        Admin Team
        wrote on last edited by
        #170 Quote Reply

          Interesting... :think:

          1 Reply Last reply
          • Metropolicity Offline
            Metropolicity
            Posts: 3,797
            Metropolicity Offline
            Metropolicity
            wrote on last edited by
            #171 Quote Reply

              @nuphoria said:
              Interesting... :think:

              Like this!

              Took a break and finally got something into CAD that I had thought about for a LONG time.

              How do you integrate a flashlight into a squirt? You 3d print one!

              Parts list:
              2x3mm LED
              3xLR41 Batteries
              1xMicro Tact Switch meant for PCBs

              Here it is exploded. The three holes in the back are for the batteries. Since the LEDS are 3V, I likely run two of batteries in parallel and one in series to that, resulting in a 3.2V cell. If my design is right, it should all press fit into place. The square is where the micro tact switch will go with the button sticking out the top. You'll notice that the "lens" is one piece, the LEDs will be pressed into place and they should fit snug. It won't be super bright but a light is better than no light. The lens will be made from super detail acrylic polymer. The rest should be made from nylon.

              Together:

              The recessed, chamfered hole should have enough space for my thumb to depress the button.

              A look at what it would look like if the lens was actually clear, it will likely be more frosted, giving a more flood/dispersed light.

              IF this works out, I am going to incorporate it into another Squirt project. The USB (Urban Survival Buddy).

              1 Reply Last reply
              • oreogaborio Offline
                oreogaborio
                Posts: 71
                oreogaborio Offline
                oreogaborio
                wrote on last edited by
                #172 Quote Reply

                  @Metropolicity said:

                  @nuphoria said:

                  Absolutely brilliant stuff.... can't wait to see the next set of scales :D

                  Oh, and about the selling of tools, I'm always here to take them off your hands! :whistle:

                  I am going to work on a set of stuff to sell on Shapeways, something you can drop in with the simple ordering of the 1/2" pivots. Making these available to anyone with a good bit of patience, steady hands and a paypal account. :D

                  smurf....

                  1 Reply Last reply
                  • lowtech Offline
                    lowtech
                    Posts: 4,799
                    lowtech Offline
                    lowtech
                    wrote on last edited by
                    #173 Quote Reply

                      You, Metropolicity, are a sick man.
                      But me likes... :D

                      I´m looking forward to the first printed LED torch to be incorporated in a tool.

                      1 Reply Last reply
                      • Metropolicity Offline
                        Metropolicity
                        Posts: 3,797
                        Metropolicity Offline
                        Metropolicity
                        wrote on last edited by
                        #174 Quote Reply

                          @lowtech said:
                          You, Metropolicity, are a sick man.
                          But me likes... :D

                          I´m looking forward to the first printed LED torch to be incorporated in a tool.

                          Me too, I've already had a problem with the stainless steel scales. Have to edit one integral bushing I made from .3 to .7mm

                          1 Reply Last reply
                          • scorpion008 Offline
                            scorpion008
                            Posts: 139
                            scorpion008 Offline
                            scorpion008
                            wrote on last edited by
                            #175 Quote Reply

                              Your mods just get better and better. wow.

                              1 Reply Last reply
                              • Grumpy Offline
                                Grumpy
                                Posts: 1,123
                                Grumpy Offline
                                Grumpy
                                wrote on last edited by
                                #176 Quote Reply

                                  You've just set the bar for the manufacturers to try to catch up!! Well done on a fantastic idea :tu:

                                  1 Reply Last reply
                                  • nuphoria Offline
                                    nuphoria
                                    Admin Team
                                    Posts: 15,038
                                    nuphoria Offline
                                    nuphoria
                                    Admin Team
                                    wrote on last edited by
                                    #177 Quote Reply

                                      Excellent - more gadgetery!

                                      I would imagine you'll get about 10-15 lumens off that, which is plenty for a little keychain option. No blue lights though, nice neutral LEDs please :pok:

                                      1 Reply Last reply
                                      • Metropolicity Offline
                                        Metropolicity
                                        Posts: 3,797
                                        Metropolicity Offline
                                        Metropolicity
                                        wrote on last edited by
                                        #178 Quote Reply

                                          @nuphoria said:
                                          Excellent - more gadgetery!

                                          I would imagine you'll get about 10-15 lumens off that, which is plenty for a little keychain option. No blue lights though, nice neutral LEDs please :pok:

                                          I ordered 20 of each, red, blue, orange, yellow and white. I'll see how it goes. :)

                                          1 Reply Last reply
                                          • Metropolicity Offline
                                            Metropolicity
                                            Posts: 3,797
                                            Metropolicity Offline
                                            Metropolicity
                                            wrote on last edited by
                                            #179 Quote Reply

                                              @scorpion008 said:
                                              Your mods just get better and better. wow.

                                              This isn't even in mod territory anymore...it's more like product design! :) finally, full circle (wayyyyy to much design school NOT to have some kind of result).

                                              1 Reply Last reply
                                              • scorpion008 Offline
                                                scorpion008
                                                Posts: 139
                                                scorpion008 Offline
                                                scorpion008
                                                wrote on last edited by
                                                #180 Quote Reply

                                                  You're right. This is brilliant design, plain and simple.

                                                  1 Reply Last reply
                                                  • enki_ck Offline
                                                    enki_ck
                                                    Global Moderators
                                                    Posts: 20,936
                                                    enki_ck Offline
                                                    enki_ck
                                                    Global Moderators
                                                    wrote on last edited by
                                                    #181 Quote Reply

                                                      I just got a new monitor today and am catching up with past threads. There are some amazing updates here. :tu:

                                                      1 Reply Last reply
                                                      • Metropolicity Offline
                                                        Metropolicity
                                                        Posts: 3,797
                                                        Metropolicity Offline
                                                        Metropolicity
                                                        wrote on last edited by
                                                        #182 Quote Reply

                                                          A tiny update.

                                                          I wanted to prep some new back springs for the second or even 3rd Splash I may make when the other parts come in. I looked at how I removed the material step by step on the current modified back springs and I did the entire material removal with my prized 6 flute solid carbide 5/8" end mill.

                                                          The end result is a set of uniform frame and back springs that have a nice cut out for the knife or tool access.

                                                          1 Reply Last reply
                                                          • legtu Offline
                                                            legtu
                                                            Posts: 119
                                                            legtu Offline
                                                            legtu
                                                            wrote on last edited by
                                                            #183 Quote Reply

                                                              impressive work! i've been following this and every revision just gets better and better. :tu:

                                                              1 Reply Last reply
                                                              • Metropolicity Offline
                                                                Metropolicity
                                                                Posts: 3,797
                                                                Metropolicity Offline
                                                                Metropolicity
                                                                wrote on last edited by
                                                                #184 Quote Reply

                                                                  Serrated Blade, MKII

                                                                  I was bored tonite and I had a free hour. I took one of my busted old P4's and took a stab at making another more refined SE blade for my Splash MKII.

                                                                  Instead of showing you the final product I decided to document how I did it from start to finish. I've researched high and low and I've come up with my best method. BUT ask 10 people how to make a SE, and you'll get 10 different answers. This is all done with exactly 3 Dremel bits. The large orange stone bit, a 1/8" diamond bit and a 1/16" diamond bit.

                                                                  First you start with measurements. I use a length of 3/8" for the large scallops and 1/8" for the small scallops. This keeps things easy because the Dremel bit is sized for the small scallops. You could go all croco teeth like my first try but this is just as good.

                                                                  Then using the orange bit and bracing your hands and fingers on the table and work, slowly kiss the edge of the blade to establish the profile of the large scallops.

                                                                  Then it's time to give those large scallops and edge. Using the same orange stone, and touching down in the middle of the curve and slide the spinning up and down the edge, stopping to make checks every 4 strokes. Don't worry too much about getting it perfect. This is to remove some material. I freehand this, but it's ABOUT 15 degrees.

                                                                  The key point here is to make all of the large scallops even, you'll be able to tighten them up after the smaller scallops and don't worry about the burr.

                                                                  Repeat the same process with the smaller scallops. Touch down in the middle, stroke up and down 4 times and check your work. If it's off center, make the next 4 strokes to compensate for it. The idea is to make these two even side by side and for the edges to touch the tips of the other scallops. Again, if you see a burr forming, and see it scallop, you are on the right track.

                                                                  By stopping and checking, it gives the blade time to cool off, if need be, let it cool for 30 seconds or if you are super paranoid, have a cool damp rag with an ice cube in it near by.

                                                                  here are all the scallops roughed in. You'll notice that I also marked a 1/8" point above the edge, this gives me a point of reference on how far I want the scallop to go.

                                                                  From here, I go back to the orange stone and touch up the big scallops, creeping closer to make the points meet on the smaller scallops. This is a touch and check, touch and check kind of procedure. Take your time, you are half way down at this point, don't want to ruin the blade.

                                                                  Heres a shot of the back side, you see all that burr and the clearly defined serrated edge. We need to reveal it now.

                                                                  I take a standard 1x30 belt sander and turn it on it's side, so the belt runs away from you. You'll have to brace tour fingers on the sander and whereever else it's safe. SLOWLY kiss the blades back side edge and you'll see the burr grind away. Careful not to grind the blade flat, just the edge. This may take 5-6 very light passes. Take breaks, dip in water if needed, but keep the blade moving while doing this, don't stop and let the belt eat too much of the blade.

                                                                  Post sander. The serrations are fully revealed, but now the burr has been reversed. It's now on the side where you ground the profiles. Time for a polish.

                                                                  With a buffing wheel, you can quickly zip away that burr, while giving the new edges and great shine.

                                                                  Once that is done, it's time for a real sharpening. A diamond cone file will give the final edge, just a few strokes will get rid of any remaining burrs. Then a stropping on the corner of a leather strop loaded with diamond.

                                                                  Sling! razor sharp.

                                                                  This step, I chose to do only because on a tiny brick of steel parallels, it's tough to tell what's what. Some file work gives a visual indication it's the SE. I went with a 2x1/16" jimps and 1x1/8" jimps, then repeat.

                                                                  Here's a comparison pic between my first go at this pattern and this latest iteration. The large scallops on the previous blade where un even, I didn't use the orange stone to grind the bevel in. I also removed a lot less material by using the orange stone to do the bevel. When you are dealing with a blade this small, you want to remove as little material as you can!

                                                                  That's all for now. I am still waiting on a huge batch of Squirts to come in. When they do, I'll tackle the other blades and document how to do those too.

                                                                  1 Reply Last reply
                                                                  • Syph007 Offline
                                                                    Syph007
                                                                    Global Moderators
                                                                    Posts: 9,842
                                                                    Syph007 Offline
                                                                    Syph007
                                                                    Global Moderators
                                                                    wrote on last edited by
                                                                    #185 Quote Reply

                                                                      Looking good. :tu:

                                                                      BTW I remembered where I found the tool to grind serrations.. but.. its 300 bucks! so.. never mind!

                                                                      1 Reply Last reply
                                                                      • Metropolicity Offline
                                                                        Metropolicity
                                                                        Posts: 3,797
                                                                        Metropolicity Offline
                                                                        Metropolicity
                                                                        wrote on last edited by
                                                                        #186 Quote Reply

                                                                          @Syph007 said:
                                                                          Looking good. :tu:

                                                                          BTW I remembered where I found the tool to grind serrations.. but.. its 300 bucks! so.. never mind!

                                                                          Yah, but that's not fun enough. It's locked to one pattern and eventually it'll wear down :)

                                                                          Thanks Rob!

                                                                          1 Reply Last reply
                                                                          • nuphoria Offline
                                                                            nuphoria
                                                                            Admin Team
                                                                            Posts: 15,038
                                                                            nuphoria Offline
                                                                            nuphoria
                                                                            Admin Team
                                                                            wrote on last edited by
                                                                            #187 Quote Reply

                                                                              Cool.... really enjoying your mini blade modding :D

                                                                              1 Reply Last reply
                                                                              • Metropolicity Offline
                                                                                Metropolicity
                                                                                Posts: 3,797
                                                                                Metropolicity Offline
                                                                                Metropolicity
                                                                                wrote on last edited by
                                                                                #188 Quote Reply

                                                                                  Got the LEDs in today!

                                                                                  Red, blue, yellow, amber and most important white.

                                                                                  These are going to be grrrrreat when they are diffused with that pseudo lens.

                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 7
                                                                                  • 8
                                                                                  • 9
                                                                                  • 10
                                                                                  • 11
                                                                                  • 18
                                                                                  • 19
                                                                                  1. Home
                                                                                  2. Tool Talk
                                                                                  3. The Mod Squad
                                                                                  4. The Splash - LM Squirt Mod
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0