Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE NOTIFICATIONS 0 MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

How to build a modern golfer (84mm cellidor)

Scheduled Pinned Locked Moved The Mod Squad
24 Posts 1 Posters 17.0k Views
  1. Home
  2. Tool Talk
  3. The Mod Squad
  4. How to build a modern golfer (84mm cellidor)
How to build a modern golfer (84mm cellidor)
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Gareth Offline
    Gareth
    Admin Team
    Posts: 37,725
    Gareth Offline
    Gareth
    Admin Team
    wrote on last edited by
    #20 Quote Reply

      @hiljentaa said:

      @Syph007 said:

      @hiljentaa said:

      Nice! You should do an Apprentice like this. I can't seem to find one anywhere...

      Ah the apprentice would be a quick build as its basically a waiter with the phillips instead of corkscrew. So you can just buy a waiter and swap in the phillips. The back phillips and corkscrews are identical between the 84 and 91 size.

      TIL. Thanks! I'll put that on the 'to-do' list. :)

      there's even a "how-to" thread for Phillips/corkscrew; </post/166447>

      :)

      1 Reply Last reply
      • nuphoria Offline
        nuphoria
        Admin Team
        Posts: 15,038
        nuphoria Offline
        nuphoria
        Admin Team
        wrote on last edited by
        #21 Quote Reply

          Outstanding job Syph - thanks for the great walk through :salute:

          1 Reply Last reply
          • hiljentaa Offline
            hiljentaa
            Posts: 314
            hiljentaa Offline
            hiljentaa
            wrote on last edited by
            #22 Quote Reply

              @Gareth said:

              @hiljentaa said:

              @Syph007 said:

              @hiljentaa said:

              Nice! You should do an Apprentice like this. I can't seem to find one anywhere...

              Ah the apprentice would be a quick build as its basically a waiter with the phillips instead of corkscrew. So you can just buy a waiter and swap in the phillips. The back phillips and corkscrews are identical between the 84 and 91 size.

              TIL. Thanks! I'll put that on the 'to-do' list. :)

              there's even a "how-to" thread for Phillips/corkscrew; </post/166447>

              :)

              :facepalm:

              Endless amounts of excellent information here! Thanks.

              1 Reply Last reply
              • Helvetica Bold Offline
                Helvetica Bold
                Posts: 891
                Helvetica Bold Offline
                Helvetica Bold
                wrote on last edited by
                #23 Quote Reply

                  @Syph007 said:
                  Ok this is how I make my backsprings. The modern backspring will become the scissor rest and the older backspring will become the body of the spring.

                  Now... since the stock hole in the modern rest is 2.5mm and I want it to be 2.2mm for an 84mm mod, what do we do?

                  We use a bushing! Now since the difference between 2.5 and 2.2 mm is not very much material for a bushing, I started by drilling out the hole to 1/8 inch since thats the size of carbide bit I had handy. The size isnt important at all, as long as its bigger.

                  Then take a small piece of brass (or nickel silver) and beat it into the hole, hit it hard on both sides so it is good and stuck into the hole. Then cut the excess off each side and sand flat and you end up with this.

                  I only have non carbide 2.2 mm drill bits, but since we are now drilling through soft brass it's no big deal, so center punch to mark and drill away. It isnt even critical at this stage to get it dead center as you will see later on.

                  And test to make sure the 2.2mm brass stock fits, and we have successfully reduced the hole size to what we need.

                  Love to have a go at this but just wondering if it is easily achievable just using the old style scissor spring? I do have both available but would rather keep the newer one for another build if possible. I do have two old ones though if that could work too?

                  1 Reply Last reply

                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                  With your input, this post could be even better 💗

                  Register Login

                  1. Home
                  2. Tool Talk
                  3. The Mod Squad
                  4. How to build a modern golfer (84mm cellidor)
                  Reply
                  • Reply as topic
                  Log in to reply
                  COMMUNITY LINKS
                  EDC-TV SAKWiki GearFeed SAKSelector
                  Operational Funds

                  Help us keep the Unworkable working!

                  Make A Donation
                  November Goal: $300.00
                  Due Date: Nov 30
                  Total Receipts: $0.00
                  Below Goal: $300.00
                  0% funded
                  • Login

                  • Don't have an account? Register

                  • Login or register to search.
                  • First post
                    Last post
                  0