Wanted: Detailed Diagram of the 91mm Plus Scales
-
try mixing up a little of your epoxy and thin it with some metho or rubbing alcohol, not too much, just enough to make it runny so you can paint it on.
-
@PTRSAK said:
try mixing up a little of your epoxy and thin it with some metho or rubbing alcohol, not too much, just enough to make it runny so you can paint it on.Awesome idea! Wouldn't of thought about that.
Someone posted some feedback on Dremel's facebook page. These look nice but think am going to pass on them for now. The information might help others.
Lee Valley - Carbide Burr Set, Set of 8
These eight small carbide burrs can be used on any steel, steel alloy, or non-ferrous metal.
Useful for detail work on hardwoods, tagua, bone, etc. 3/32" shanks. 1-3/4" long.

-
The miniature neodymium magnets arrived!! The shipper sent 60 of the lil' buggers!

Along with some natural Tagua Nut. Think the vegetable ivory will be too pale for the Silk Oak wood am using though. May have to stash them for another time, or find a home for them. :D
Now the fun begins. Hopefully the 100% Tung Oil will arrive by the weekend.
Oh, after measuring the scales, seems the second set is at 4mm. That's going to be a close call to sneak a pen slot in since a pen is 2.5 mm thick. Will see. The grain is more attractive than my first set too.For future reference:
Since the polarity is across the flat surface of a magnet, keep the width down to 2mm or less. 3mm wide means a 3mm deep hole into the scale material if you want a specific polarity.
To maneuver the magnet use the end of a straight pin or a fine finishing nail. File the head to a more flat surface if needed, as straight pins have a ^ type of head. -
Fist set of scales are about done past sealing and finishing, but I am not satisfied with them being so thin. Both scales are around 4.5mm to 5mm. The pen is really close to the surface, can feel the pressure when working that channel. Feeling the file is not a good sign. There should be more space there.
However the tweezers side is about good on space. But want to keep both scales the same width, yet don't want a fat knife either. What to do...Other scales are 5mm thick on average, which are ready to be worked out. this means the top & bottom of one scale would be very light sanding if am going to make the clearance.
Another option would be is to kick the toothpick out and just go with tweezers on one scale, pen on the other scale. May go with that and see how it holds up.Blank is 11mm thick. Have no mechanical means of reducing the width to 7mm.
What the issue was trying to save the wood by trying to get two sets of scales out it. Giving the saw blade width that cut things way too close. Ended up having to add side strips. Adding material to the sides was not hard, but it still entailed using glue.
Width on the other hand. 11mm, cut in half, 1mm thick saw blade, gave 5mm. Once on starts flattening and sanding that 5mm turned to near 4mm, and thus there's just not enough material to last years down the road. One bad fall would result in a cracked scale.Corkscrew is 7.5mm wide. From the spacer to the outside it is 4.5mm. Shouldn't the scale should be at least 4.5mm to match, or 5mm?
Anyone have a 91mm Plus scale laying around, and could measure it's average thickness for me?
have found out the neodymium magnets can be files down with a diamond file. :D
-
Showing the current status of the first set of 91mm Plus 'Silk Oak' scales, average 4.5mm thickness.
Top View

Inside Overview

Inside - Low Profile

-
Basic shape roughed in. Burled Yellow Box. (not oiled yet, just a bit of water on them to show the grain)
These are for a sportsman/tourist/small-tinker, not decided which they are going on yet.Got these and another pair out of one slab with enough to do several 58mms as well.
Will cut some 91mm scales out of the other slab.
-
How thick are your scales?
-
Going to bed aggravated. The second set was too thin. Have another 11m blank that am going to stagger cut and somehow take down 4mm while working with it. So smurfin' let-down, broke the scales.
The diagonal pen idea was working out but it also made the 4mm scale too weak. 1.5 mm is not enough room for structural integrity.
RIP secondary set.
-
Not sure if it is to any use right now, but I glue the scales on very rough shaped. Don't bother getting the outer shape exact at this point. Just the rivet holes need to be precise. I'm leaving 1 or 2 mm wood around the edges and plenty thick. Once the epoxy is set start shaping the scales from coarse to fine. I do leave the T&T out, making it an even simpler job.
-
@Wootz said:
Not sure if it is to any use right now, but I glue the scales on very rough shaped. Don't bother getting the outer shape exact at this point. Just the rivet holes need to be precise. I'm leaving 1 or 2 mm wood around the edges and plenty thick. Once the epoxy is set start shaping the scales from coarse to fine. I do leave the T&T out, making it an even simpler job.Your idea helped. Also one fellow at Home Depot suggested the idea I had in mind to use, was to cut what was needed first the size it down.
Had set the holes, whacked the raw scales in with a light-weight rubber mallet, shaped them from a raw 11mm blank. Added channels to fit the scale tools, got them within tolerance.
Looked around the tool, decided on 7mm thickness. Cut small sections with a coping saw, and a my Charge TTi's S30v blade for slicing the sections off from the end to the other. Shaped it down with a Dremel sand roller.
Mounted them on the Climber again, decided to take the middle down to 6mm, giving a small flat face on the side. Sanded down that down, filled some holes. Waiting for them to cure in before I proceed further.Been using the small driver on a Squirt S4 as a chisel to cut square holes for the magnets. Then have to epoxy them in. Haven't put the pin in yet.
Was thinking of heating another pin and pressure burn a hole through into the wood. Not sure how this will work. Cutting a thin pin channel on the other scales was iffy. If there is the slightest gap between the scale & knife the pin just will <u>not</u> doesn't cooperate.
Could cut a deeper channel, then glue a toothpick or sliver of scrap wood over the back & sand it down. This reverse frame idea might work better. Least it looks good on paper. :D -
Something I was thinking about. Keep seeing these branches/trunks of wood with their bark still attached to furniture, cabinets, even house trim. The knots, limbs, and other imperfections are only cut off. They are shaped to remove rough edges, looking like either a clean slice with rounded corners or chopped segments.
People buy this rustic look. Why not get some limbs and make rustic wood knife handles too? Am sure someone's already down that to other fixed knives, but not seen a SAK handle like that yet. Would definitely make for a unique look - maybe for display or gift.
-
You want a comfortable grip, no limbs sticking out for me.
-
@Wootz said:
You want a comfortable grip, no limbs sticking out for me.Oh, I agree. Get a load of these bed posts. /shakes head

Cut a pin groove, flipped a blade over on the spine, skived that out slowly. Wished could somehow secure the pin to staying in the groove I cut for it. Put a magnet, north facing towards the pin, and have it setting up in the clamp.
Have a magnet in the tweezers, and another at the head of the pen channel. They are tiny lil' rascals and are only powerful at close proximity. So they have to be touching or close to hold any metal in the grooves.Was crazy, the first scales I made are at 4mm and are waiting for the tung oil to arrive. The third set is at 6mm, and gluing magnets in and touching up some areas.
Not sure what else to use to seal the wood. Tried mixing the gel epoxy, but that stuff doesn't come out of the tubes evenly. Was no individual epoxy tubes available. All were the double-chambered one-piece syringes. One comes out easy and too much, the other sits there then comes out at once - in small amount. Cut it with nail polish remover (acetone). It is still drying.
Our area seriously lack a hobby & craft shop.Picked up this Locktite Gel epoxy for what it bonds to. 6 minute setup though.


-
Hate mixing epoxy. Rarely do I actually get the right mixture to where it sets up like it should. Have a sealant layer on the 3rd set of scales. Had to redo the sealant mixture on the 1st set as the epoxy was still tacky after 8 hours.
Note: Looks like it is setting up. :whew:
The 1st set is ready for the tung oil, and the 2nd will be ready if this sealant mixture sets up.
Black spots are the teeny neodymium magnets. May have to add a secondary south-touching magnet for the pin groove since was unable to burn a straight groove through the wood, and that testing is showing the pin wants to launch upwards. If there's a slight gap between the scale and the knife, that will cause issues. Better to get it right the first time.
3rd set of scales is 6mm.
-
Now I haven't used tung oil in ages.

Guess the Tung oil application is going to take days, or a week. :ahhh
-
Read an interesting article on oil finishes, and how various finished came about, were blended, other forms that came into play, and label trickery. Oil Finishes: Their History and Use
It is a very good read.

-
There's much to discover on this board, grasshopper. :D
</topic/42415
-
Scales look good to go. Had a few minor finishing repairs, mostly to the sidewall of the mounting hole that lies between the toothpick & pen grooves. Applied two thin coats of epoxy thinned down with rubbing alcohol to seal the wood. Removed the epoxy from the mounting holes before it fully cured.
Hoping I can get an equal amount of epoxy mix to mount the scales on. Which color/half of the epoxy should get the most of, since they do not always come out equally: white or the colored-yellow gel? Doesn't say which one is the hardener. Don't want a runny mix. :ahhh
In the past, many many years ago, had mixed a tad more hardener to get a firmer grip. So do not like mixing as if not enough of one or the other then it never hardens. Should of looked elsewhere and picked up separate tubes instead of a syringe container.
Should I epoxy the scales on first, or does it matter if I oil them up before application? Reason why I ask is the first coat of oil is suggested to keep applying till the wood soaks up all it can hold. Then buff out the risen wood particles and dried finish before applying a second coat. Was told this could take up to five subsequent thin coats to get the maximum benefit from the Tung oil.
-
Both sets 1 & 3 are ready for the finishing process. First set on the Spartan is at 4mm, 3rd set on the Climber at 6mm. :D
Corkscrew side

Awl side

Edit: The texture on my very first set looks terrific! Am anxious to see how the Tung oil will look on them. :D
-
In the dunny (great place to multitask at) looking at the transparent blue sapphire scales of my Climber, and how I had abused them in such a short time. Looked at the plain scale and noticed that Victorinox had polished their name on the inside, left most everything else dulled down.
Looked at a recess of a possible button area, a + area, and then a tiny bit of shiny caught the light. Pulled out the short blade, and looky at what I got!
Looks like I get to add a small metal Victorinox shield logo in my knife handle now. :D

Too bad it is so thin. Thought it might make for a neat wood burning emblem maker. Only soldering iron I have is a portable butane one with a catalyst chamber. A Rat Shack version.

So I got a little surprise this evening. The one time wishing I had a small exact-o knife set.

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login