Surge Owners Club
-

Get a load of this poor soul. Been through hell and back and still works great. It has loosened up almost to the point of being too much but the locks hold true. I do edc other tools when not in uniform and when smaller tools are more appropriate but for the big stuff nothing beats a surge except an actual wrench with a bag of screwdrivers.....
-
Looks like a well used and trusted companion mate

-
Today I bought the Bit Extension and my Surge is now almost complete (I'll get a set of T- shank saws from Bosch next). But I had some problems.
The extension is very loose in the holder. For the time being I improvised a simple solution; I used a rubber band that provides friction in the holder and now it is impossible to slip off. The rubber band (black in the picture but a simple beige rubber was also tested and works) can be used on the pliers head in order to make it a vise-grip. But I wonder about your solutions. A mini Maglite fits better there but mine is modificated for astronomy and I use my iPhone as a torch.
Second, the Leatherman bits fit tight and the thin ones are difficult to remove. But the Hex bits are even more difficult. I realized that there is no magnet inside but a kind of spring. Will it get lose with time? If you push the bit more it dives inside (because it isn't double) and it can be removed only with the pliers with some difficulty (thankfully the pliers is available). So, is this normal and usual?
Far from these the extension works very well, also as a standalone driver. I am thinking about an accessory that would provide more torque in order to use it more as a standalone. Do you have a proposition for how could I do it?
Thank you!

-
I don't know how you would get more torque out of the extension - so, sorry. However, I do know that the extension should fit in there pretty tightly. I mean, I just checked mine and there is some wobble, but it should be reasonably tight.
Hex bits are rather tight and I've had to, at times, do a shirt-over-pliers move to take them out without gouging the bits.
I don't know; hope that helps...
-
Get a load of this poor soul. Been through hell and back and still works great. It has loosened up almost to the point of being too much but the locks hold true. I do edc other tools when not in uniform and when smaller tools are more appropriate but for the big stuff nothing beats a surge except an actual wrench with a bag of screwdrivers.....
Is your serrated blade worn

-
I've had my surge for awhile now and I've noticed quite a bit of movement in the scissor hinge (rivot)?) , the point at which the scissor action actually is. The blades have quite a bit of slop in them. It still cuts just fine, but I was wondering if this was normal. It has been like this since it was new.
NOTErized!
-
@ Kukamunga
In my case the extension can't stay in place without the rubber.
I've seen somewhere an add on that provides a better grip. I'll search for it. -
@ carlb
My scissors have a play that vanishes when the spring is engaged.
The blades had some play, a great part of which is fixed with adjustment of the screws (10 Hex safety bit needed). When locked there's no play.
My Surge doesn't rattle as I've read at Grant Lamontagne's review. Perhaps they fixed that problem now (it is a 12/12 model and the review is a few years old). -
I found a way, very easy.
Now,will the MIT bits fit?

-
@kkokkolis said:
@ KukamungaIn my case the extension can't stay in place without the rubber.
I've seen somewhere an add on that provides a better grip. I'll search for it.Well, I'm no LM expert, but to my mind you shouldn't have to mess with a brand new bit extender on a brand new Surge, right? However, if it's a pain to send back, etc., etc. - then I guess you jury rig it. But you shouldn't have to; seems something's wrong with the tolerances there.
-
found a Like New Surge on Craigslist for $20. To bad its a bit to far to make it worth getting.

-
The extender is OK, although there is some play. The holder in the seath seems a bit wider than what it should be. But I am happy with the solution I've found.
-
Here is an idea for using and storing the MUT bits, bypassing the loose holder at the same time:
And here a modification of the pry blade

http://www.themodguys.com/2009/05/leatherman-punchdown-tool.html
I don't have the tools for either though.

-
Clever idea for carrying the bits

-
I just bought some Bosch compatible jigsaw blades. As already mentioned by others, they are almost half compared to the Leatherman saws. Can anyone explain his solution for minimizing blade play? Pictures are much welcomed!
Thanks. -
@kkokkolis said:
I just bought some Bosch compatible jigsaw blades. As already mentioned by others, they are almost half compared to the Leatherman saws. Can anyone explain his solution for minimizing blade play? Pictures are much welcomed!
Thanks.I heard a lot of things with tape... Ducttape, electrical tape, stuff like that ;)
-
I tried it. It gets better but it still has some play. The new Surge will be having the best solution perhaps. If they would be selling the new holder we could upgrade our older tools.
-
Heat shrink. Works great for me. Sorry, was gonna take some pics for you today but forgot.
-
Email response from Leatherman.co.uk
Thank you for your email and interest in the Leatherman products.
We have been in contact with our Suppliers and they are looking at the new Surge been available around June. -

Sam works for leatherman.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login