Northern Industrial Multitools 'Mountain Edition' ... take one
-
Me likey :D
Cheap,
Scissors AND awl AND bit driver
Outboard and non-lockingSometimes I wish the bigger manufacturers would emulate the cheapo's instead of the other way round

-
I got one similar to this used, on Ebay, for $5.43, including shipping, with a case. The brand on the knife base is Fury and it seems to have been sold by Capitol Supply. For a "cheapo", this thing is solid!!. I Was able to put a pretty good edge on the knife, and, at least in my case, the pliers are solid, with no play. I like the fact that the pliers have a wire stripper at at the base of the cutter, and that all of the tools are outboard deployable. Having a magnetic bit holder with common size bases gives you the ability to mix and match 10 of your most used bits. I like solid tools and this one fits the bill. At the very least, you could bludgeon someone with it. I'm not a small guy, so a little extra weight doesn't bother me at all. Goes to show that not having a "Big Dog" name doesn't always mean you have to stay on the porch!!..........in mho..........

-
I think this thing would be a pretty good bargain at $6 shipped.
I had a few more comments I thought I'd add after a little more time playing with this thing. I took a file to the sharp edges of the handle, and knocked it down to just 'uncomfortable' instead of 'painful'. I can honestly live with it. I'd suspect that most of the time when you're applying excessive force to an MT would be while clamping the plier head closed, not while using the externally accessible tools. This design is fine in plier configuration.
A few notes on the bit holder: First, I closed it with the largest flathead still in the holder, and there was no obstruction. So, along with the bits in the little plastic carrier, you could stow another bit in the holder itself, and not interfere with the tool's function. Next, the strong magnet of the bit holder transmits its magnetism through the bit. This means you could use a bit to pick up small items made of ferrous metals, like small screws or other bits. The weight of a hex bit is right on the edge of what can be lifted. The strength of the magnet holding the bit in the tool will hold (I'm guessing) about a pound. That doesn't sound like a lot, but when you try to pull the tapered philips bit out, it seems like a ton. The magnet is strong enough that if you hold the tool only by the bit, it won't pull out. Very, VERY impressive retention. The case is large enough to allow another set of hex bits to be stuffed in with the set included, so you could have a good deal more than are even supplied with the tool.
I would have liked to see a saw on this tool. The tool that holds the bits has a base that is considerably wider (maybe 2mm) than the barrel that holds the bits. I think a little work with a file would make room on that side of the tool to squeeze in a modified hacksaw blade.
-
that would be a really useful mod. Post some pictures if you are able to make it work, and you might inspire me to try the same on mine. :sak:
-
@50ft-trad said:
Me likey :DCheap,
Scissors AND awl AND bit driver
Outboard and non-lockingSometimes I wish the bigger manufacturers would emulate the cheapo's instead of the other way round

Exactly. I suspect that if this was made by LM it would be hailed as a sucess.
Nice review Lynn, cheers.

-
I have this same tool as was given too me
it reminds me of bears & sons mt's my only gripe I found was some of the tools are fiddly too open,but a very well made tool and UK legal, nice review lynn 
-
Pics of mine lynn



-
Few more


-
Nice! Does yours get any actual use?
Mine, sadly, is not likely to live a very adventurous life.
-
Just wondering...any comparison shots of the size of the plier head on this compared to any other well-known tools? I've always wanted an oversized pair of plier jaws like on a Super Bear Jaws, but I'm suspecting this isn't quite that big...
-
I'm afraid I don't have a lot of full size big-name tools at the moment.
Here's what I DID have for comparison. The Sheffield PST clone (which as I recall was pretty dead on to scale with the PST).
Then the Mountain MT in question.
The Victorinox Spirit X.
The Kobalt 15-in-1
and the Gerber Bear Grylls 'Strata'Comparing it to the picture in this post by Neal...
</post/192241>I think the head is about the same length as the Super Bear Jaws, but with smaller standard plier area, and more needle nose section.
Hope this helps somewhat.

-
Yeah, I think you're right on that. We have a Northern store up here, so I might go take a look in person. Thanks for the pic!
-
Feel free to enter the give-away for one of these that I'm running right now (drawing on April 17, 2013). Here's the thread...
</topic/44144
-
An update here. The giveaway mentioned in the previous post has finished. Now, I hope AdmSlc will give us his thoughts on the tool once he's had a chance to play with it a bit.
-
I have two of these multi tools! I have had them for years, maybe 10 or so. I got them at a gas station when we lived in Raleigh, and liked the first one so much, I went back and bought a second! Mine have no brand name on them though. I will agree that for a cheap tool, it is very well made. I mainly like the way the bit holder is made on it. I actually like that better than any multi tool I have, and I own a ton of them!
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login