Wood Scaled SAK pictures thread.
-
That Spartan is
!@Sags said:
Just curious what kind of finish you guys are using on your wood.I've always used polyurethane, just wondering what the advantages of different finishes are... mineral oil, linseed, waxes, etc...
You know, I get paid for this sort of info.... ;)Wax - Very limited protection, not very durable. Needs frequent reapplication. Not what I'd recommend for knife handles.
Linseed oil - Limited protection to the wood, will darken the wood. It can be fairly durable depending on how many coats are applied.
Tung oil - More water resistant than linseed oil, not as dark as linseed. Again, fairly durable with multiple coats.
Oil based polyurethane - Very tough finish, almost plastic-looking. Oil based polys will yellow over time. Requires some sanding between coats, and usually takes about 30 days to cure fully and achieve full hardness.
Water based polyurethane - More transparent than oil based, will not yellow. Needs more coats than oil based for the same level of durability. Requires some sanding between coats, and takes about 10-15 days to fully cure. This is what I've used to refinish the handles on several Opinels. If going this route, I'd recommend finding one rated for floors. There are a lot of brands out there that are not.....
Lacquer - Very hard but brittle. Lacquers are less durable than you'd expect, especially on something that's going to be riding around in a pocket. Higher quality lacquers require spray equipment to apply.
Hope this helps anyone looking to do a project like this. If anyone has refinishing questions, feel free to PM me.

-
@ Subterranean & jerseydevil: Thank you guys for your positive feedback! :)
-
@jerseydevil said:
That Spartan is
!Just curious what kind of finish you guys are using on your wood.
I've always used polyurethane, just wondering what the advantages of different finishes are... mineral oil, linseed, waxes, etc...
You know, I get paid for this sort of info.... ;)(...)
Hope this helps anyone looking to do a project like this. If anyone has refinishing questions, feel free to PM me.

Thx for your overview. I'm currently trying a recommendation of a carpenter. In Germany we call it "Hartöl". But I don't find any reference in English wikipedia.
That Hartöl is some kind of cooked linseed oil (cooked without air supply / vent). Making it more viscous. With that Oil you treat your wood and (in my case) wait for 8 hours and polish it using cotton tissues.
-
Sounds like Boiled Linseed Oil, which is what I use on my wood scales.
I prefer oiled finish to "Polyurine" as my late father used to call it.
He was a boatbuilder and preferred oil or natural varnish on nice timber because "parrotpiss" made it look like wood-grained plastic.
-
@PTRSAK said:
Sounds like Boiled Linseed Oil, which is what I use on my wood scales.Ah, found it. Thanks to your reference. Look here (Wikipedia)
For me it sounds, that "Hartöl" is something like Stand Oil or Boiled Linseed Oil. But I'm no expert and just got that oil from the Carpenter (Father in Law) and it works. That finish now still feels like wood also looks like it's more durable. Long term evaluation will show if it's really good.
-
Has anyone ever used Tru Oil?
-
-
-
-
-
and last but by no means least,
Grevillea
These have all (except the Yellow Box) been built on BNIB SAKs, stripped down and rebuilt with exposed rivets through the scales. The wood is finished with multiple coats of Linseed oil.
They will all be for sale, along with numerous 84mm Tourist and Sportsman models also in various exotic woods.
I just have to work out a price...
-
Very nice knifes. I like the different woods and exposed rivets! :D (Just one little thing. It's important to flatten the rivets very exactly before peening. One or two had cracks
:) )Price calculation is very difficult here. You don't have scale tools, but the work is quite accurate and the phases are hand made. Chris (from custom works) sells some wooden knifes for 40-60€s which is ok but imho still to less. Looking at his techniques which allows him quick work it seems reasonable, however.
But such knifes with peening ... I don't know. I don't want to ask, how many hours you spent on one knife. Would be nice to see, how much you can get.
-
Loving these wodden scales!
Here's one I picked up a week or so ago, a Super Tinker in Kingwood/Ash Burl with leather spacer:

-
@HankSolon said:
Very nice knifes. I like the different woods and exposed rivets! :D (Just one little thing. It's important to flatten the rivets very exactly before peening. One or two had cracks
:) )If you mean cracks in the rivets, I think it is more a "trick of the light". There may be a couple of rivets where the wood didn't sand down quite flush with the end of the rivet. One is where i used my last piece of 2.2 rod and it was a tiny bit shorter than I would have liked.
It is hard to see in person but the camera shows it up quite markedly.
It's also hard in a photo to show the grain looking as good as it does "in the flesh".Still, overall I am very happy with the way these have turned out and as far as price goes, I'm not looking at making a living off these, but more hoping for them to be a self funding hobby.
If I can cover my costs and make a bit extra to buy more materials I'm happy.
-
Did this as a Fathers' Day gift, Wenger Ranger 61 in Maple. Also personalized with the family brand opposite the shield/button.



Ignore the finger smudges on the blade, was to lazy to polish it before pictures.
-
This thread makes me


-
They look very nice Peter

I would like to have a go at a Spartan with exposed rivets, do you have any tips for getting the tension correct?

I’ve been known to over do my peening :-[
-
@sparky415 said:
They look very nice Peter
I would like to have a go at a Spartan with exposed rivets, do you have any tips for getting the tension correct?

I’ve been known to over do my peening :-[
I slide a piece of 5 or 10 thou shim brass in between the layers on the pin that I'm preening.
Peen it up snug but not mashed toghther and when you slide the shim out afterwards it leaves a little clearance and the blades open easily. -
They look very nice Peter

I would like to have a go at a Spartan with exposed rivets, do you have any tips for getting the tension correct?

I’ve been known to over do my peening :-[
I slide a piece of 5 or 10 thou shim brass in between the layers on the pin that I'm preening.
Peen it up snug but not mashed toghther and when you slide the shim out afterwards it leaves a little clearance and the blades open easily.Thanks Mate

I will keep my eyes open for an old feeler gauge or something at the carboot sales
[](http://s112.photobucket.com/user/sparky_415/media/hammerc.gif.html) -
Old knives in a new dress: Victorinox Vintage Olive


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

















