NEW Leatherman SURGE owners club.
-
For those still crying about no Eyeglass Screwdriver on New Surge.
-
@Lam.Kampfer said:
For those still crying about no Eyeglass Screwdriver on New Surge.+1

-
Absolutely brilliant idea. As I have the small bit in my bit kit I used it once or twice in a pinch by holding it with the pliers. But it's a pain to use it that way, you have solved my problem :)
Please write to leatherman with this idea, also post it in the mod squad. Many people sacrifice the small driver for other tools, but with your solution all you need is to drill a small hole with dremel somewhere on the tool to accomodate the bit. -
@Lam.Kampfer said:
For those still crying about no Eyeglass Screwdriver on New Surge.So simple in just putting the eyeglass driver bit in the slot where the belt/lanyard clip goes in with the spring lock holding it in place. No need for any drilling or anything and just removing it and putting it back in the bit card when done. I just tried it with my Wave and it works just as well.
-
By "drill a hole in any tool" I meant that you can do this even on mt without the pocket clip slot. Like rebar or wingman.
-
For those still crying about no Eyeglass Screwdriver on New Surge.
So simple in just putting the eyeglass driver bit in the slot where the belt/lanyard clip goes in with the spring lock holding it in place. No need for any drilling or anything and just removing it and putting it back in the bit card when done. I just tried it with my Wave and it works just as well.
Exactly, no modification.
Fine for driving small screws, but not for poking or drilling. -
@BigMatt said:
By "drill a hole in any tool" I meant that you can do this even on mt without the pocket clip slot. Like rebar or wingman.Depending on how much torque you would need to tighten an eyeglass screw, the tension on the Rebar locking tab should be strong enough to hold the bit and tighten/loosen a tiny screw. Just tried it with my Rebar and it held enough to loosen and then tighten a screw on a pair of sunglasses. :D
You're right though, on a Wingman/Sidekick there isn't a locking tab, hole, or any slot to slide the eyeglass driver bit into. :(
On another note, I'm going to have to make a trip over to the Army Exchange to see if they got any New Surge BO versions in. Haven't seen any New Surge (SS or BO) at the Navy Exchange yet. :o
-
DIY file / saw blade sleeve -> </topic/50191
-
I am still very pissed about they did not fix the pock clip issue.
-
I love the new surge
. so much better for a few reasons i even started edcing it in my back pocket. My old surge rattled even with the blade ex-changer empty. If I picked the tool up and let one side hang down it would open a tiny bit it wasn't bad or faulty and didn't ruin function. But I have handled other LM tools with nice tight lock ups and solid construction not a hint of change jangle. plus the end caps looked over tightened and warped.This Updated Surge is fantastic its build solid all my old concerns are addressed and i got less BO rub off than my first one. Now if they would make a better pocket clip that didn't wobble in the surge they would have covered all bases for everyone. I didn't mind they ditched the little eye glass driver i always figured if you dropped that tool on your glasses it would smash them any way. -
Welcome to MTO and the new Surge club.
-
@Lam.Kampfer said:
Welcome to MTO and the new Surge club.Thanks :)
-
While there is a smurf storm on east coast, it is beautiful out here on west. 6 Hours hiking trip with the heaviest MT, no problem.
-
I am in 2x!!!


There is always a way, hack on!
-
-
@Metropolicity said:
I am in 2x!!!

There is always a way, hack on!
So much rubber. :ahhh
Did you get a retail store contract to make slingshots? ;)
Glad you finnaly got an SS one, Dan.

-
Thank you. It was a lot harder then it needed to be. Thankfully there are a lot of awesome folks on here who are willing to help when they can.

-
I am in 2x!!!


There is always a way, hack on!
So much rubber. :ahhh
Did you get a retail store contract to make slingshots? ;)
Glad you finnaly got an SS one, Dan.

I got a huge box of off cuts from a friend who makes slings full time. A lot of thinner stuff but it still makes for great lightweight bands!
There is always a way, hack on!
-
All those bands...you can rig one of those surges to be a sling shot. Open it up and hold it upside down
-
@SublimetalMsG said:
All those bands...you can rig one of those surges to be a sling shot. Open it up and hold it upside downYou mean like this :)



Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


