Bit driver vs 3d phillips
-
I haven't tried the bit adaptor yet. I need to get one.
It would be a nice addition to Little Boy and the Fat man thread. :)
You know what ITGeek
I think you may be right.
But
I don't think I have any room left in my skinith for it.
then again
it might be just the thing for the little boy kit in trying to make up for this summer.I got to do some thinking.
-
I haven't tried the bit adaptor yet. I need to get one.
It would be a nice addition to Little Boy and the Fat man thread. :)
You know what ITGeek
I think you may be right.
But
I don't think I have any room left in my skinith for it.
then again
it might be just the thing for the little boy kit in trying to make up for this summer.I got to do some thinking.
What can you do without from the Skinth to make room for the bit adapter and bit card? It may be worth it to drop a dedicated folder for it and use the MT's blade instead... Hmm.
-
I haven't tried the bit adaptor yet. I need to get one.
It would be a nice addition to Little Boy and the Fat man thread. :)
You know what ITGeek
I think you may be right.
But
I don't think I have any room left in my skinith for it.
then again
it might be just the thing for the little boy kit in trying to make up for this summer.I got to do some thinking.
What can you do without from the Skinth to make room for the bit adapter and bit card? It may be worth it to drop a dedicated folder for it and use the MT's blade instead... Hmm.
I'm pretty happy with my fat man skinith setup the way it is.
I do think it would work awesome with my rebar kit.
I should be able to slid it in the sheath that came with it.
I just posted a topic for one in the tools wanted thread.
I need to get the rebar kit ready. Summer is coming fast.
-
@ITGeek said:
Dnyc, i like the sound of your wave mod!Does the lock still work with the rebar phillips? Do you think the rebar awl could also replace the small bit driver?
I see a set of security torx bits as my next purchase.
ITGeek -- yes, the Rebar tools fit nicely in the Wave/Charge, and the locks work as intended. :)
however, there will be some grinding/minor modifications required to allow the Wave/Charge to close fully. here's a pic of a Wave with Rebar drivers in the handles... notice the gap between the handles.

and here's a shot that shows a stock Rebar awl on top, and a Rebar awl that I put in a Wave and ground down to allow the Wave to close properly:

hope this helps!
-
Breezy, would the choice of rebar or wave plier head affect the ability to close fully?
Looks like it's time for me to start hanging out in the mods forum.
-
@ITGeek said:
Breezy, would the choice of rebar or wave plier head affect the ability to close fully?Looks like it's time for me to start hanging out in the mods forum.
maybe... but I'm pretty sure you'd have to do some grinding either way. the Wave in the first pic I posted has the Wave plier head in it; the awl in the second pic was ground down to fit in a Wave with the Rebar plier head.
I'm not sure if anyone has been able to get a Rebar Phillips driver into a Wave as just a straight drop-in without any modification (with either plier head).
-
I wouldn't really say that I prefer one over the other, but both definitely have their places. I carried a Surge for several years, and found myself needing a 3D Phillips for recessed screws. That's why I recently got a ST300 to pair with it. Now I use the Phillips on the ST300 for recessed screws or screws that really need torquing down, and the Surge for stuff that requires more specialized bits.
-
I have both, across several LM tools. Versatility is the name of the game for me, so the flat bits can't be beat. Although I find I don't use it often, I EDC a coin purse with the full suite of flat bits. It rides light, flat and comfy, in a pocket that I normally never use anyway.
I rarely have to deal with recessed screws, but it seems like when I do, it isn't the same size as the ST300/Crunch phillips anyway so I still have to get a dedicated tool. The bit kit extender can also improve depth access in some situations. And for true diehards, the MUT bits will get you down deep.
Of course, a blend of your own past experiences and tool expectations will dictate what is right for you.
-
I like the flat bit. And if I need a long driver, I use the Mutt bits.
live from Nate's mobile
-
I see now that carrying extra bits does not necessarily mean sheath or bag carry. my assumption was that if you are carrying extra flat bits you probably wouldn't mind carrying the bit adapter for the 3d phillips.
But the long mutt bits and the coin purse sound like pocket friendly carry methods for extra bits.After a bit more reading on MTO i also see that for anyone likely to see screw heads beyond phillips and slotted, like Canadians, the bit holder would be superior to the 3d phillips, even for pocket carry.
That being said, i'd still love to see LM sell a tool with the rebar drivers, awl, and plier head and the wave outside tools. I'm probably not looking to try my hand at modding one,after hearing how much grinding is needed.
-
I like having both, so my Rebar does.
-
The coin purse idea works really well for me. It's not obtrusive at all and doesn't make your sheath feel like a 90's cell phone hanging off your belt with all those bit cards jammed in there.
I took some inspirational photos for you. Well, inspirational to me at least

P1020738 by climbercraig66, on Flickr
P1020739 by climbercraig66, on Flickr
P1020741 by climbercraig66, on Flickr
P1020743 by climbercraig66, on Flickr -
@ITGeek said:
After a bit more reading on MTO i also see that for anyone likely to see screw heads beyond phillips and slotted, like Canadians, the bit holder would be superior to the 3d phillips, even for pocket carry.I use phillips a lot, but semi regularly come across square drive and torx and others. Even so I prefer the 3d phillips because it's better at its job than the 2d counterpart. I always wonder just how much my Wave'll take before it snaps that little driver holder. It's only thin metal.
Plus carrying the 1.5" (or whatever it is) adapter isn't really a problem as it rides with my bit kit all the time anyway since I never know what LM I'll have on me day to day. I can still use the bits regardless so it doesn't bother me much.
-
I would also add that the flat bit extender can be a nice stand-alone tool on low-torque screws, whereas I rarely carry my 3D adapter and wouldn't find it useful for anything other than its intended use.
Additionally, I would not carry any MUT bits or adapters in my coin purse; I think they would all be too long or too thick.
-
When comparing screwdrivers, especially the very commonly used Phillips bits, I see a number of performance factors.
Size range. Phillips bits don't have to be the perfect size to fit the fastener the way Allen and Torx do, so one bit will fit a number of sizes. I've seldom had a problem with this using multitools.
Torque limits. The nature of the driver tip puts a practical limit on the torque that can be applied. True 2D drivers like that found in the Micra doesn't "index" in the screw head, so it wants to "hinge" out of the screw head. That and it will apply torque to only some of the grooves in the screw head and is more likely to strip the screw out under load. "Squished" drivers like the Wingman index and grip the head better, and can apply more torque. Full size drivers like the Juice line and the Rebar are better still.
Shank length. This gives knuckle clearance to the work surface and the ability to turn recessed screws. Of course, the usefulness of this metric is related to
Shank width. The Wingman has a nice, long Phillips driver, but the shank is so wide that it won't go into screw recesses. This is a problem with any bit set, because the bits are usually 1/4" in at least one dimension and must be set into a driver that's wider than that. However, sometimes you want a short driver to reach a screw in a crevice. A partially-opened Juice might serve in that capacity.
Variety of sizes/types. Multis with fixed drivers almost always have one Phillips driver and at least one slot driver, usually several. Tools with bit drivers are usually compatible with a wide variety of bits--Leatherman has their proprietary bits, almost every other company uses standard 1/4" bits or other standard hex sizes. They usually come with a +/- bit, others can be purchased separately.
These factors effect the ability to fit whatever fastener you must turn, the ability to reach it, and the ability to provide adequate torque without damaging the fastener or camming out.
How about this: Take the Charge AL, scrap the flat blade and tiny driver, and replace with the Phillips from the Rebar. Phillips screws are so common that a dedicated, low compromise driver is worth it, leaving the bit driver to handle all the "strange" stuff. One bit card with metric allens, torx, a couple slot drivers and that #3/#0 Phillips bit would get you through basically anything. I'd probably package it with the full bit kit anyway though.
-
Craiger, those are some cool pics!!!
live from Nate's mobile
-
I'm liking this coin purse idea more and more. Then I could actually carry all the bits. Hmmm :P
-
Problem with the coin purse is that the bits will get all jumbled up, so finding the right one will be a pain.
Anyone else want Leatherman to make a double-sided bit card?
-
@av8r1 said:
Problem with the coin purse is that the bits will get all jumbled up, so finding the right one will be a pain.Anyone else want Leatherman to make a double-sided bit card?
A 2-sided bit card is a great idea but more so they need to make their sheath hold it. I can only fit one card in my rebar sheath forcing me to choose my most likely 10 needed.
-
The new sheaths for the Surge kinda suck. The older ones had a place for the bit card and one for the saw and file. New ones don't. Just for the file and saw or the bit card.
live from Nate's mobile
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login