Spyderco Byrd Wrench
-
The screwdriver can be used in both the 180 degree position or even with the tool taken apart in two. This allows holding a nut with the adjustable wrench while tightening the screw with the screwdriver bit.
-
Using the screwdriver in both 180 position & taken apart.
-
There are plastic friction holders to hold the bits in. Note the bunged screw at the bottom of the adjustable wrench at right. :(
-
The adjustable wrench opens smoothly to 3/4". I don't think you get much torque at 3/4, but at 5/8 it should be fine.
-
Showing inserting the rasp into the spring & also the flat part resting against the bits.
-
The blade is easily opened one handed & looks like the typical Spyderco Byrd blade - very nice. With the tool taken apart the Blade & handle are very sleek.
-
Here you can see how the blade rests against the detached plier jaw & also how the blade fits onto the pivot point.
-
The blade seems a little undersized for the tool when the tool is fully assembled. It's a bit of a handful to use this way, but it is fairly comfortable.
-
The finish is not perfect by any means. You can see welds & missed sanding points in some places.
-
Again the finish scratches fairly easily - a little steel wool would make it fine again though. Hey - it's a tool!
-
The blade is CR13 steel. I'm not extremely familiar with this steel. I'm told it is a higher carbon version of 440.
-
I'm fairly pleased with this tool even with the surface imperfections & quirky design. I need to use it a bit to really find out how useful it is. I've read where some folks consider it a novel playtoy & others get some serious work out of it.
It has a good clip & fits nicely in my pocket even though the rasp could chew up your pants if you aren't careful when inserting & pulling it out of your pocket.
It's no heavier than the Wave it was pictured with at the beginning of the review.
So far I'd give it a 4-4.5 out of 5. I'm looking forward to getting to know this little Byrd.
-
After re-reading this I can see it's not the best review I've written - I'm a little tired after 4 gigs today, but I wanted to get it posted before the night was out since I promised I would. On the other hand, if a picture is worth a thousand words there should be 70,000 words or so here.
-
Great review! I'll get it transferred to the main site as soon as I get a chance...
Def
-
I've finally gotten the hang of the macro lens & settings on my Nikon. I wish I had a better flash now.
-
Wonderful pictures and descriptions Tom. Don't sell yourself short, I think it was worth at least 75,000 words, maybe 80,000. ;)
I was holding my SpydeRench in my hand as I read through your review. I see a few minor differences, like the Byrd logo instead of the Spyderco spider. I think the only significant differences are the magnetic bit driver (instead of the Spydie's detent driver) and the round rasp.
It seems like the rasp would be limited in it's usefullness, to put it politely. I suspect the old three-sided diamond file was deemed too expensive, but a fine-toothed file seems like it would have been more useful?
-
I was thinking about the rasp too & was lamenting that it didn't have the diamond file. As I thought of it for my uses I may end up using the rasp more often than a diamond file though, so I'll be okay with it. I did think of modding a diamond sharpening rod to fit into the same spot though.
One question - does your SpyderWrench have a lot of friction in the outer of the two positions in the slip-joint of the pliers? Mine binds quite a bit in that position, but I thought it might be to keep it from rattling. In the inner position it moves very freely as you would expect.
-
Mine swivels freely in both positions. However, I just am now noticing that the pivot T-stud on mine has been ground down (very slightly) around the edges. This work looks to have been done by hand, probably in order to allow it to move without binding in the round pockets.
Can you see any shiny spots on yours where it is rubbing?

-
Mine binds quite a bit so there are definite shiny spots. I'd be more likely to file the round part rather than the T-stud to make mine move more freely. It doesn't bother me too much now though.
-
@Tom Munch said:
I was thinking about the rasp too & was lamenting that it didn't have the diamond file. As I thought of it for my uses I may end up using the rasp more often than a diamond file though, so I'll be okay with it. I did think of modding a diamond sharpening rod to fit into the same spot though.That would be interesting. Or how about maybe a firestarter ferro rod?
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login