The Hacked Leatherman Owners Club.
-
@kkokkolis said:
I was just checking and found that the scissors and blade exchanger plus blade are too long to fit. The scissors are also too wide. I was interested in a simple exchange. I'll have to continue using my Swisschamp's scissors and awl. But good luck to you and don't forget to update.will do.


-
@kkokkolis said:
I was just checking and found that the scissors and blade exchanger plus blade are too long to fit. The scissors are also too wide. I was interested in a simple exchange. I'll have to continue using my Swisschamp's scissors and awl. But good luck to you and don't forget to update.The scissor out of a 91mm SAK will fit in a Wave or charge. You will have to do some grinding.
Nate
-
I was just checking and found that the scissors and blade exchanger plus blade are too long to fit. The scissors are also too wide. I was interested in a simple exchange. I'll have to continue using my Swisschamp's scissors and awl. But good luck to you and don't forget to update.
The scissor out of a 91mm SAK will fit in a Wave or charge. You will have to do some grinding.
Nate
yup!
I mostly want to try the Surge scissors just to see if I can pull it off. :D -
I was just checking and found that the scissors and blade exchanger plus blade are too long to fit. The scissors are also too wide. I was interested in a simple exchange. I'll have to continue using my Swisschamp's scissors and awl. But good luck to you and don't forget to update.
The scissor out of a 91mm SAK will fit in a Wave or charge. You will have to do some grinding.
Nate
yup!
I mostly want to try the Surge scissors just to see if I can pull it off. :DI'm not liking the Wingman scissors very well just yet. May have to find some 91mm or Surge scissors and try this. I already put my spare Surge scissors in the ST300.
-
@Breezy12 said:
yup!
I mostly want to try the Surge scissors just to see if I can pull it off. :D@zoidberg said:
I'm not liking the Wingman scissors very well just yet. May have to find some 91mm or Surge scissors and try this. I already put my spare Surge scissors in the ST300.It's been done by one of the members of another forum, if memory serves me right it was over at British Blades.
The mod while functional, left a lot to be desired. The Surge scissors were just too long for Wave/Charge, so the modder had to saw off quite of bit of the tips leaving the unsightly and stumpy looking implement. The problem with Surge scissors isn't so much the length of its blades but the long handles. As a result a scissor pivot is too far down and blade tips need to be almost cut in half to fit the Wave/Charge cavity.
If I was doing this mod I would rather focus on the handle bottom stop and remove the little nub to add few more mm in total cavity length.
-
yup!
I mostly want to try the Surge scissors just to see if I can pull it off. :D@zoidberg said:
I'm not liking the Wingman scissors very well just yet. May have to find some 91mm or Surge scissors and try this. I already put my spare Surge scissors in the ST300.It's been done by one of the members of another forum, if memory serves me right it was over at British Blades.
The mod while functional, left a lot to be desired. The Surge scissors were just too long for Wave/Charge, so the modder had to saw off quite of bit of the tips leaving the unsightly and stumpy looking implement. The problem with Surge scissors isn't so much the length of its blades but the long handles. As a result a scissor pivot is too far down and blade tips need to be almost cut in half to fit the Wave/Charge cavity.
If I was doing this mod I would rather focus on the handle bottom stop and remove the little nub to add few more mm in total cavity length.
Move the pivot back to make up for the tip cut, use the old pivot as a paracord cutting notch?
-
If I was doing this mod I would rather focus on the handle bottom stop and remove the little nub to add few more mm in total cavity length.
Move the pivot back to make up for the tip cut, use the old pivot as a paracord cutting notch?
Hmm, not sure, it may turn a bit ugly, but be my guest. :P
You have my moral support, mate

-
:D Thanks but due to a lack of funds and parts I won't be trying anything for a while.
-
yup!
I mostly want to try the Surge scissors just to see if I can pull it off. :D@zoidberg said:
I'm not liking the Wingman scissors very well just yet. May have to find some 91mm or Surge scissors and try this. I already put my spare Surge scissors in the ST300.It's been done by one of the members of another forum, if memory serves me right it was over at British Blades.
The mod while functional, left a lot to be desired. The Surge scissors were just too long for Wave/Charge, so the modder had to saw off quite of bit of the tips leaving the unsightly and stumpy looking implement. The problem with Surge scissors isn't so much the length of its blades but the long handles. As a result a scissor pivot is too far down and blade tips need to be almost cut in half to fit the Wave/Charge cavity.
If I was doing this mod I would rather focus on the handle bottom stop and remove the little nub to add few more mm in total cavity length.
that's pretty much what I had in mind... I think I'd also have to shorten the pivot if I remove/grind down the bottom handle piece on the Wave.

zoidberg, I agree with you about the Wingman scissors. they work well enough in my skinny ReCharge because I use them for a very specific purpose (cutting open small plastic packages in the lab at work), but for general purpose use, they're certainly not the best scissors. :(
I picked up a couple used 91mm Vics on ebay awhile back, I think I'll try those scissors next.
-
that's a lot of hacking going on
-
-
-
Very cool!
-
@hiraethus said:
A bit of grinding, sanding and layer swapping later:

Nice lightweight, UK friendly multi tool now. Just need a pocket clip and it'll be done.looking good!
did you have to grind the plier head at all to allow clearance for the Vic scissors, or were the scissors thin enough to allow clearance? -
Thanks! Not the pliers, but I did sand down the plastic liner next to the scissors and ground about 0.5mm of the thickness of the Phillips driver to give the scissors more space. I had to add a thicker washer between the pliers and the liner to take up the gap - I should have left a thicker portion at the pliers end.
-
Just a hint on something nice I've been working on... ;)
Still adding final few touches, not sure when will I be able to complete it, work is currently hectic.

-
:D

That reminds me i have to work on the refurbish of my polishing machine (atm still a big bad 12" grinder).

-
Would love to have a go at polishing my Wave once I get home.
Anyone know of a thread or guide how to go about something like this?
-
@hiraethus said:
Hacked Wave with Wingman scissors, small bit driver removed and awl/small flat driver added:

Not sure how I missed this but did all the parts you added come from the Wingman?
Also is the Scissors mod a simple drop in?
Thanks.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login

