Multitool TLC
-
-
@Pablo O'Brien said:
Spoiler alert: Pabs was in the tumble weed.Seeing how many turns it made...
Plausible -
After over half a decade last week my Charge ALX got minor service. Sprayed with WD-40. Cleaned out using a paper towel, q-tips, and a Gum soft pick. Then I coated with WD-40 silicone spray and wiped off with a rag.
-
@MastyrOfPuppitz said:
After over half a decade last week my Charge ALX got minor service. Sprayed with WD-40. Cleaned out using a paper towel, q-tips, and a Gum soft pick. Then I coated with WD-40 silicone spray and wiped off with a rag.Good choice in lubricant
The water resistant WD-40 SpeSmurfpillst silicone is fantastic! I really like it because is not as heavy as lithium lubricant. Barely spritzed on my multi-tools and pocket knives and they open/close super smooth. A great product for small tools. -
Just read the WD40 comment, and just wanna share some of my experience.
Long ago I stored a Wave in a plastic drawer, thinking with the WD40 bath it took and the dry weather, it should be safe for long term storage.
I kinda forgot about that Wave in the drawer, and many months later, it developed rust across the entire handle and within the tools. All the other LMs have survived more humid weather with no lube(except joints), but how wrong I was about WD40 and its 'rust prevention'.
Till this day, I still don't thoroughly understand what might have happened, but hardly any rust spots have developed ever since I abandoned using WD40.
-
To clean out tight spaces I twist up a small scrap of paper into a rigid swab. Occasionally I rinse out my SAKs and GAK with water. For my every day MTs and knives I use what ever oil is handy, very often it's cooking oil. The tools and knives that get stuck in drawers I grease with Sil Glyde. I use compressed shop air to blow out dirt and grime a couple times a year. I have never encountered a knife or multi tool that required chemicals to clean, but I would use brake clean spray if I did.
-
@comis said:
Just read the WD40 comment, and just wanna share some of my experience.Long ago I stored a Wave in a plastic drawer, thinking with the WD40 bath it took and the dry weather, it should be safe for long term storage.
I kinda forgot about that Wave in the drawer, and many months later, it developed rust across the entire handle and within the tools. All the other LMs have survived more humid weather with no lube(except joints), but how wrong I was about WD40 and its 'rust prevention'.
Till this day, I still don't thoroughly understand what might have happened, but hardly any rust spots have developed ever since I abandoned using WD40.
I had a similar experience with WD 40. I stored tools coated with WD 40 inside a sealed ammo can 6 months later they were covered in rust. I won't buy it any more and only use it as a last resort.
-
@Scorpion Regent said:
I have never encountered a knife or multi tool that required chemicals to clean, but I would use brake clean spray if I did.I'll just add that one need to be careful with brake cleaning products, and in particular those for spraying which disperses all around in the air. Quite a few brake cleaning products contain hydrofluoric acid. While that no doubt makes them effective it also puts them firmly in the dangerous category.
Hydrofluoric acid is not only an acid and a poison if you eat or breath it, but also a contact poison. Thus if you get some on your skin it will go into your system. Once entered in some way it does the full range from flu sympoms and skin destruction, via serious diseases and bone dissolving, to causing cardiac arrest or internal organ failure. Hydrofluoric acid do maim and kill people so please be aware of it and treat it with respect if you have to use it.
Personally I don't consider cleaning wheels or anything else important enough to risk exposure, so I make sure any such products don't contain hydrofluoric acid before I get them. (To the degree I trust the brand product label in the first place that is).
-
After adding a cable cutting tool to my Leatherman Surge, I decided to modify it to fit my needs. I will be adding and modifying several things going forward in the hope of building my perfect multi tool.
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login