Compact double ended bits
-
Not a daft question as they will not attach to many bit holders. Wiha who makes these naturally also makes tools that hold these. I suspect a magnetic holder with some depth will also work. I don't know if they have the ratcheting style of tool your prefer. I think I've seen short double ended bits like this from others too, so there might be more sources.
As for only imperial the 1/4 inch hex bits standard size is indeed imperial, and I've only seen these for the 1/4" standard. Other double sided bits exists for 4mm hex precision bit standard. I'm not aware of any double sided bits for the 8mm hex bit standard. Leatherman and Nextool (and maybe more) make their own non-standardized flat holder double ended driver bits.
(Nice pictures Grand Banana - somehow I've overlooked this until now. Interesting tiny bits!)
-
@Vidar said:
Not a daft question as they will not attach to many bit holders. Wiha who makes these naturally also makes tools that hold these. I suspect a magnetic holder with some depth will also work. I don't know if they have the ratcheting style of tool your prefer. I think I've seen short double ended bits like this from others too, so there might be more sources.As for only imperial the 1/4 inch hex bits standard size is indeed imperial, and I've only seen these for the 1/4" standard. Other double sided bits exists for 4mm hex precision bit standard. I'm not aware of any double sided bits for the 8mm hex bit standard. Leatherman and Nextool (and maybe more) make their own non-standardized flat holder double ended driver bits.
(Nice pictures Grand Banana - somehow I've overlooked this until now. Interesting tiny bits!)
Great answers, thanks! Had a peek at the wiha website but no obvious bit holders specifically for their double ended bits. I think trial and error will have to be the solution.
Another space-saving rabbithole I'm going to look at is the precision 4mm bits, available up to PH2, 4mm hex, 4mm flat and T20 torx. Not found a source for PZ2 yet. I figure the 4mm can replace at least 8 of my 1/4" bits if I'm putting together a "comprehensive" kit Vs "minimalist". Would need an adaptor, which subtracts points..... I can see a spreadsheet coming along

-
4mm precision bits typically come in big sets with lots of bits of all kinds. I'm sure the sites of Primes and Alis have plenty to offer. And there are some nice handles with double ended bits inside available too. (There is a 24 in 1 with double ended bits in the handle that is quite nice. Not the cheapest, but nice, and rotating top which tend to be helpful in actual use with these).
As for holders for those 1/4" double ended ones a 1/4" hex socket with holding function will likely do the trick too. (I only have those in metric so I can't check).
A note about a 4mm bit holder adaptor is that they can often do double duty as a 4mm hex socket driver as well. (Not uncommon size in electronic sized parts).
-
-
-
Been looking for these as I want to fit Torx in my Ozark Trail Multiforce without adapters. I'm guessing these don't have ball bearing retention, though? The Multiforce has a magnet in its extension, but not the driver itself.
The Industrial set should do nicely for what I need. Also, getting a 3D printer next month (assuming the FlashForge prices stay low in July), so I'll probably print up a holder.
-
I know this is a bit of a zombie thread, but thought some might like to know. These fit the newer Milwaukee Fastback 6 in 1, the model where the bit driver has the ball detente, not the older style with the snap ring bit holder. The bits are slightly shorter than the one that comes with it, but stick out plenty and work just fine.
-
@ReamerPunch said:
There is a tiny driver branded Steinwhale with double-ended bits that are shorter than regular bits. I might get it.I have got that. The driver is nothing special but the bits are quite decent, though I havenโt used them a lot. You can put them in a standard bit socket but the head does not protrude much and it can be a chore pulling them out with fingers, as there is not much to grip. Life is easier if you use them when pliers are to hand.
EDIT: I somehow missed Grand_Bananaโs far more comprehensive post on this. Oh well.
-
-
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better ๐
Register Login



