Single-wing Wingman
-
That's a really cool mod. I wonder if you could do the same kind of thing with a wave or surge?
-
Great mods guys. Nice way to make the tool slim yet still functional.
-
Just a thought: Single-wing Wingman = Swing-man?
-
@Kampfer said:
... then discovered that the SE blade became a real hazard as its tip stick out from the opening of handle. So SE blade is not more.You can add the box cutter from your spare Wingman (unless you got rid of it) instead of that small SE blade you removed.
The non-interference between the tools is unfortunately only possible with 4 tools or less. Add the 5th (like Wave scissors or Rebar awl or similar) and it will have to cover at least one if not two tools on the opposite side when closing. I wouldn't worry about that. The emphasis should be on a tool load you can comfortably install inside the handle's cavity not so much the tools covering each other, in this case. Well at least to me ;)
-
That is a cool mod!
-
I have zero spare parts. :-[ But now I do. ;)
-
Love the mod. Looks very..........departs to buy yet another multi ;)
-
@babola said:
I was pretty sure this had been done before by some of the modders here, as it's such a logical and straightforward way to finish up with by following the Mini-Surge mod. I am currently collecting bits for my own Mini-Surge mod, Wingman scissors being one of them.This left me with a scissor-less Wingman, and since I am OCD and cannot stand Wingman pliers I decided to create a 'mini-tool folder' in a single Wingman handle.
What made this mod easier was the fact the top (pliers-end) and bottom (tools-end) pivot sizes on Wingman are the same size, allowing me to install the tools from a bottom of one handle into the top of the other, basically combining the Wingman's tool load into a single handle. To top it all off, I also added scissors from the Wave.
The result was quite surprising to me as it required very little modding while creating almost a perfect small 'MT-folder' as an end result.
The top tools fit snugly into the handle and the Wave scissors fold in perfectly. The only rule of thumb is to fold the bottom tools into the handle first, and top tools second, on top of the bottom tools. This is required as there's simply not enough space for the tools to fold independently inside the main handle cavity due to their length.
Few details:
- I used a Wingman handle housing a 420HC combo blade
- Bottom tools in that handle were left untouched
- Internal pliers stop strip had to be removed by breaking a rivet, to allow the installation of the tools at the top of the handle. This is a must.
- Phillips and flat head screwdrivers from the second handle were installed at the top of this handle
- Wave scissors added and installed in a particular position (see photos below) over the bottle/can opener for correct fit
- After extensive play with different sized washers and spacers (all sourced from Wingman's second handle) I ended up with this combo.
- All button screw heads flattened. As much as I like button heads their prominent bulge was a little out of place for me personally on this tool, they are much bigger than the ones on Wave/Charge/Surge.












Hope you like it :)
I like this half a wingman better than a actual fully loaded wingman.
babola -
Neat mods!
-
thats fantastic!
-
So I started on this mod, but I had to take a work call. So I have a pile of drivers, washers, and handles on my desk. I'll have to finish in the morning.
-
great idea and execution -
kamp I have a few wave/charge scissors laying around...
Josh
-
@firefightingjosh said:
kamp I have a few wave/charge scissors laying around...Josh
Thanks man!
PM in bond . -
WOW, this almost convinces me that a wingman/sidekick is a tool worth having if only as a donor for this mod.
THIS is a LM folder done right.
and I'm sure a little bit of effort could shoehorn a pair of Vic scissors in there somewhere. maybe the size from a 74mm like an Executive

-
That's incredible. I kinda sorta hope A Leatherman Tool Rep is looking at this post. Maybe they could do some damage to coughcough*** saks....
I for one have never owned a real SAK....but making one out of a Leatherman is now on my todo list.
-
That is one sexy mod!
How is the ergonomics? Could it benefit from some thin scales?
That would be perfect for the MTO 3d printing project. MTO Swingman scales.Sent from a device made from star dust using tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login