Multitool TLC
-
WD40 in a pressurized can,fine brush,and Q-tips works for most crud.
-
Def, whatever happened to the graphite/aluminum experiment?
-
-
Is there an echo in here? :P
Absolutely nothing happened. I don't have any pictures of the arrangement I had set up, but basically I had an aluminum liner on a plate, inside a Rubbermaid cake thing- the kind used for transporting cakes. I put water in the inverted Rubbermaid lid, put the plate in the center (the plate kept the scale from actually being in the water), then put the graphite all over the scale. I had even scuffed the scale somewhat to make sure if there was any coating on it, the aluminum would be exposed. I then put the clear lid over the whole thing and let it sit in my kitchen, where the temperature varies greatly depending on the time of day, or whether I am cooking anything. I figured different temps might have different effects.
After about six weeks I gave up on it and cleaned the mess up- the liner had no issues whatsoever.
Def
-
Reading the TLC thread, it seems there are 4 schools of camp when it comes to lubricating multitools:
- WD-40
- Various oils, like 3-in -1, gun oils, etc. either all over on just on joints
- Mineral oil and Inox on joints
- Nothing
I don't know anything about this stuff, but I was instinctively leaning toward nothing, and perhaps using mineral oil or graphite only if the joints became stiff. (That graphite is amazing stuff. I was a convert the first time it miraculously repaired a completely frozen lock with a small squirt.)
Anyway, the majority seem to favour WD-40 or oil of some sort. Is coating the entire tool really necessary? Doesn't it make it greasy and slippery?
-
Since this thread is fresh in my mind, I thought I'd also post a quick summary of cleaning methods for future readers.
This is just off the top of my head, so please excuse any ommissions:
Cleaning:
-
Most people either use WD-40, or water with some sort of soap.
-
For cleaning utensils, people often use rags, toothbrushes, q-tips, & toothpicks
-
Special cleaning methods include:
- Blowing out dirt with a can of compressed air
- Sticking blue tac inside grooves to picks up little bits of dirt, etc.
- Using unwaxed dental floss to clean inside joints of pliers and tools
- Putting SAKs and Vic MTs in the dishwasher
- Opening & closing joints under running water, or while swishing the tool around in water
-
Drying is extremely important. Some people leave the tool opened to air dry. Some use a hair dryer or something similar.
-
-
@max6166 said:
Anyway, the majority seem to favour WD-40 or oil of some sort. Is coating the entire tool really necessary? Doesn't it make it greasy and slippery?I've never done extensive testing or anything, so I can't really say what's entirely necessary. But... I've been using WD-40 for serious cleaning and 3-in-1 for general lube. I just put a small drop on most of the pivots and work it in a bit. Sometimes I wipe some on the blades/tools, but not much. When I'm done I wipe the whole thing off with a cloth (just cut up t-shirts...). It doesn't seem slippery or overly oily to me, though the next couple of times I use the tool I might notice a little oil seeping out. I usually go a while between cleaning/lubing, so that doesn't bother me too much.
-
That's easy, buy it, decide the two of you don't gel, then sell it before the factory oil even wears off. Hmmm, sounds a lot like mickyd. :D
Mike
-
dential floss! I would have never thought about that.
see, I've already learned something new!
ironhand
-
-
I'll be honest. I don't really do much cleaning on my multi tools. I sharpen the knife if it gets dull. I haven't oiled the Pulse in I don't know how long. I oil the blades on the Wave every once in a while with some FP-10 gun oil.
I've used carb & choke cleaner to blast out grit before, or just over-oil the joint and work the pliers for a while. ALl kinds of black stuff comes out every time I do that.
-
I just soak them in warm soapy water over night and then using either a pick or toothpick and pipe cleaners. I get the yucky stuff out.
Using a combo of M3 pads or steel eraser and paste.
But for oil I use olive oil on the pivots and blades. That way when one cuts food they don't get the WD 40 taste.
-
I have found that Buck honing oil cleans up LM diamond files like new!
-
anyone use Remington gun oil with Teflon? I take my tools out and regrease them every month as i live in Houston. Seriously living here is like going to a sauna and spraying a bottle of hot piss in your face. Dirty shady town. >:D
-
I haven't tried RemOil.. :( I try to stay away from any oils in my multi-tools as they attract gunk.. I use dry film lubricants like Tuf Glide. Tuf glide is waterproof, it doesn't attract gunk, and it lasts a LONG time! Not to mention that it basically seals the steels pores so it makes it have a much better rust resistant finish. I would never use anything else!
-
@Leatherman123 said:
I haven't tried RemOil.. :( I try to stay away from any oils in my multi-tools as they attract gunk.. I use dry film lubricants like Tuf Glide. Tuf glide is waterproof, it doesn't attract gunk, and it lasts a LONG time! Not to mention that it basically seals the steels pores so it makes it have a much better rust resistant finish. I would never use anything else!YAY Tuf Glide user!!!
I bought a little tuf glide kits for my edc bag...good stuff!
-
Tuf glide eh? where uall getting this stuff? I'll try it.

-
Here's the kit I have: http://www.denverdiscoun[url=http://forum.multitool.org]multitool[/url].com/KNIVES/KNIVES---ACCESSORIES/MOSS91200.html
An excellent price indeed! :)
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
:D